75 lines
3.1 KiB
C
75 lines
3.1 KiB
C
|
#define MICROPY_HW_BOARD_NAME "NUCLEO-L152RE"
|
||
|
|
#define MICROPY_HW_MCU_NAME "STM32L152xE"
|
||
|
|
|
||
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
||
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
||
|
|
// This board has an external 32kHz crystal
|
||
|
|
#define MICROPY_HW_RTC_USE_LSE (1)
|
||
|
|
#define MICROPY_HW_ENABLE_SERVO (1)
|
||
|
|
#define MICROPY_HW_ENABLE_DAC (1)
|
||
|
|
|
||
|
|
// HSE is 8MHz, HSI is 16MHz CPU freq set to 32MHz
|
||
|
|
// Default source for the clock is HSI.
|
||
|
|
// For revisions of the board greater than C-01, HSE can be used as a
|
||
|
|
// clock source by removing the #define MICROPY_HW_CLK_USE_HSE line
|
||
|
|
#define MICROPY_HW_CLK_USE_HSI (1)
|
||
|
|
|
||
|
|
#if MICROPY_HW_CLK_USE_HSI
|
||
|
|
#define MICROPY_HW_CLK_PLLMUL (RCC_CFGR_PLLMUL6)
|
||
|
|
#define MICROPY_HW_CLK_PLLDIV (RCC_CFGR_PLLDIV3)
|
||
|
|
#else
|
||
|
|
#define MICROPY_HW_CLK_PLLMUL (RCC_CFGR_PLLMUL12)
|
||
|
|
#define MICROPY_HW_CLK_PLLDIV (RCC_CFGR_PLLDIV3)
|
||
|
|
#endif
|
||
|
|
|
||
|
|
// UART config
|
||
|
|
#define MICROPY_HW_UART1_TX (pin_A9)
|
||
|
|
#define MICROPY_HW_UART1_RX (pin_A10)
|
||
|
|
#define MICROPY_HW_UART2_TX (pin_A2)
|
||
|
|
#define MICROPY_HW_UART2_RX (pin_A3)
|
||
|
|
#define MICROPY_HW_UART3_TX (pin_B10)
|
||
|
|
#define MICROPY_HW_UART3_RX (pin_B11)
|
||
|
|
#define MICROPY_HW_UART4_TX (pin_C10)
|
||
|
|
#define MICROPY_HW_UART4_RX (pin_C11)
|
||
|
|
#define MICROPY_HW_UART5_TX (pin_C12)
|
||
|
|
#define MICROPY_HW_UART5_RX (pin_D2)
|
||
|
|
// UART 2 connects to the STM32F103 (STLINK) on the Nucleo board
|
||
|
|
// and this is exposed as a USB Serial port.
|
||
|
|
#define MICROPY_HW_UART_REPL PYB_UART_2
|
||
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
||
|
|
|
||
|
|
// I2C buses
|
||
|
|
#define MICROPY_HW_I2C1_SCL (pin_B8) // Arduino D15, pin 3 on CN10
|
||
|
|
#define MICROPY_HW_I2C1_SDA (pin_B9) // D14, pin 5 on CN10
|
||
|
|
#define MICROPY_HW_I2C2_SCL (pin_B10) // Arduino D6, pin 25 on CN10
|
||
|
|
#define MICROPY_HW_I2C2_SDA (pin_B11) // Arduino D3, pin 31 on CN10
|
||
|
|
|
||
|
|
// SPI buses
|
||
|
|
#define MICROPY_HW_SPI1_NSS (pin_A15) // pin 17 on CN7
|
||
|
|
#define MICROPY_HW_SPI1_SCK (pin_A5) // Arduino D13, pin 11 on CN10
|
||
|
|
#define MICROPY_HW_SPI1_MISO (pin_A6) // Arduino D12, pin 13 on CN10
|
||
|
|
#define MICROPY_HW_SPI1_MOSI (pin_A7) // Arduino D11, pin 15 on CN10
|
||
|
|
|
||
|
|
#define MICROPY_HW_SPI2_NSS (pin_B12) // pin 16 on CN10
|
||
|
|
#define MICROPY_HW_SPI2_SCK (pin_B13) // pin 30 on CN10
|
||
|
|
#define MICROPY_HW_SPI2_MISO (pin_B14) // pin 28 on CN10
|
||
|
|
#define MICROPY_HW_SPI2_MOSI (pin_B15) // pin 26 on CN10
|
||
|
|
|
||
|
|
#define MICROPY_HW_SPI3_NSS (pin_A4) // Arduino A2, pin 32 on CN7
|
||
|
|
#define MICROPY_HW_SPI3_SCK (pin_C10) // Arduino D3, pin 31 on CN10
|
||
|
|
#define MICROPY_HW_SPI3_MISO (pin_C11) // Arduino D5, pin 27 on CN10
|
||
|
|
#define MICROPY_HW_SPI3_MOSI (pin_C12) // Arduino D4, pin 29 on CN10
|
||
|
|
|
||
|
|
// USRSW is pulled low. Pressing the button makes the input go high.
|
||
|
|
#define MICROPY_HW_USRSW_PIN (pin_C13)
|
||
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
||
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
|
||
|
|
#define MICROPY_HW_USRSW_PRESSED (0)
|
||
|
|
|
||
|
|
// LEDs
|
||
|
|
#define MICROPY_HW_LED1 (pin_A5) // Green LD2 LED on Nucleo
|
||
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
||
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
||
|
|
|
||
|
|
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_1
|