micropython/ports/stm32/boards/NUCLEO_F767ZI/mpconfigboard.h

// This board is only confirmed to operate using DFU mode and openocd.
// DFU mode can be accessed by setting BOOT0 (see schematics)
// To use openocd run "OPENOCD_CONFIG=boards/openocd_stm32f7.cfg" in
// the make command.

#define MICROPY_HW_BOARD_NAME       "NUCLEO-F767ZI"
#define MICROPY_HW_MCU_NAME         "STM32F767"

#define MICROPY_HW_HAS_SWITCH       (1)
#define MICROPY_HW_HAS_FLASH        (1)
#define MICROPY_HW_ENABLE_RNG       (1)
#define MICROPY_HW_ENABLE_RTC       (1)
#define MICROPY_HW_ENABLE_DAC       (1)
#define MICROPY_HW_ENABLE_USB       (1)

#define MICROPY_BOARD_EARLY_INIT    NUCLEO_F767ZI_board_early_init
void NUCLEO_F767ZI_board_early_init(void);

// HSE is 8MHz
#define MICROPY_HW_CLK_PLLM (4)
#define MICROPY_HW_CLK_PLLN (216)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (9)
#define MICROPY_HW_FLASH_LATENCY (FLASH_LATENCY_7) // 210-216 MHz needs 7 wait states

// UART config
#define MICROPY_HW_UART2_TX         (pin_D5)
#define MICROPY_HW_UART2_RX         (pin_D6)
#define MICROPY_HW_UART2_RTS        (pin_D4)
#define MICROPY_HW_UART2_CTS        (pin_D3)
#define MICROPY_HW_UART3_TX         (pin_D8)
#define MICROPY_HW_UART3_RX         (pin_D9)
#define MICROPY_HW_UART6_TX         (pin_G14)
#define MICROPY_HW_UART6_RX         (pin_G9)
#define MICROPY_HW_UART_REPL        PYB_UART_3
#define MICROPY_HW_UART_REPL_BAUD   115200

// I2C busses
#define MICROPY_HW_I2C1_SCL         (pin_B8)
#define MICROPY_HW_I2C1_SDA         (pin_B9)
#define MICROPY_HW_I2C3_SCL         (pin_H7)
#define MICROPY_HW_I2C3_SDA         (pin_H8)

// SPI
#define MICROPY_HW_SPI3_NSS         (pin_A4)
#define MICROPY_HW_SPI3_SCK         (pin_B3)
#define MICROPY_HW_SPI3_MISO        (pin_B4)
#define MICROPY_HW_SPI3_MOSI        (pin_B5)

// CAN busses
#define MICROPY_HW_CAN1_TX          (pin_B9)
#define MICROPY_HW_CAN1_RX          (pin_B8)
#define MICROPY_HW_CAN2_TX          (pin_B13)
#define MICROPY_HW_CAN2_RX          (pin_B12)

// USRSW is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN        (pin_C13)
#define MICROPY_HW_USRSW_PULL       (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED    (1)

// LEDs
#define MICROPY_HW_LED1             (pin_B0) // green
#define MICROPY_HW_LED2             (pin_B7) // blue
#define MICROPY_HW_LED3             (pin_B14) // red
#define MICROPY_HW_LED_ON(pin)      (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin)     (mp_hal_pin_low(pin))

// USB config (CN13 - USB OTG FS)
#define MICROPY_HW_USB_FS              (1)
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
#define MICROPY_HW_USB_OTG_ID_PIN      (pin_A10)