2018-02-20 22:35:05 +00:00
|
|
|
#define MICROPY_HW_BOARD_NAME "NUCLEO_H743ZI"
|
|
|
|
|
#define MICROPY_HW_MCU_NAME "STM32H743"
|
|
|
|
|
|
|
|
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
|
|
|
#define MICROPY_HW_ENABLE_ADC (0)
|
|
|
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
|
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
|
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
|
|
|
|
|
|
|
|
#define MICROPY_BOARD_EARLY_INIT NUCLEO_H743ZI_board_early_init
|
|
|
|
|
void NUCLEO_H743ZI_board_early_init(void);
|
|
|
|
|
|
|
|
|
|
// The board has an 8MHz HSE, the following gives 400MHz CPU speed
|
|
|
|
|
#define MICROPY_HW_CLK_PLLM (4)
|
|
|
|
|
#define MICROPY_HW_CLK_PLLN (400)
|
|
|
|
|
#define MICROPY_HW_CLK_PLLP (2)
|
|
|
|
|
#define MICROPY_HW_CLK_PLLQ (4)
|
|
|
|
|
#define MICROPY_HW_CLK_PLLR (2)
|
|
|
|
|
|
|
|
|
|
// 4 wait states
|
|
|
|
|
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4
|
|
|
|
|
|
|
|
|
|
// UART config
|
|
|
|
|
#define MICROPY_HW_UART3_TX (pin_D8)
|
|
|
|
|
#define MICROPY_HW_UART3_RX (pin_D9)
|
|
|
|
|
#define MICROPY_HW_UART_REPL PYB_UART_3
|
|
|
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
|
|
|
|
|
|
|
|
|
// I2C busses
|
2018-03-19 13:10:57 +00:00
|
|
|
#define MICROPY_HW_I2C1_SCL (pin_B8)
|
|
|
|
|
#define MICROPY_HW_I2C1_SDA (pin_B9)
|
|
|
|
|
#define MICROPY_HW_I2C2_SCL (pin_F1)
|
|
|
|
|
#define MICROPY_HW_I2C2_SDA (pin_F0)
|
2018-02-20 22:35:05 +00:00
|
|
|
|
|
|
|
|
// SPI
|
|
|
|
|
//#define MICROPY_HW_SPI2_NSS (pin_I0)
|
|
|
|
|
//#define MICROPY_HW_SPI2_SCK (pin_I1)
|
|
|
|
|
//#define MICROPY_HW_SPI2_MISO (pin_B14)
|
|
|
|
|
//#define MICROPY_HW_SPI2_MOSI (pin_B15)
|
|
|
|
|
|
|
|
|
|
// USRSW is pulled low. Pressing the button makes the input go high.
|
|
|
|
|
#define MICROPY_HW_USRSW_PIN (pin_C13)
|
|
|
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
|
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
|
|
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
|
|
|
|
|
|
|
|
|
// LEDs
|
|
|
|
|
#define MICROPY_HW_LED1 (pin_B0) // green
|
|
|
|
|
#define MICROPY_HW_LED2 (pin_B7) // blue
|
|
|
|
|
#define MICROPY_HW_LED3 (pin_B14) // red
|
|
|
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
|
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
|
|
|
|
|
|
|
|
|
// USB config
|
|
|
|
|
#define MICROPY_HW_USB_FS (1)
|
|
|
|
|
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
|
|
|
|
|
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
|
