2015-12-08 14:41:47 +00:00
|
|
|
#include STM32_HAL_H
|
|
|
|
|
|
2015-11-24 13:35:24 +00:00
|
|
|
#define MICROPY_HW_BOARD_NAME "F429I-DISCO"
|
|
|
|
|
#define MICROPY_HW_MCU_NAME "STM32F429"
|
|
|
|
|
|
|
|
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
2016-02-06 12:48:58 +00:00
|
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
2015-11-24 13:35:24 +00:00
|
|
|
#define MICROPY_HW_HAS_SDCARD (0)
|
|
|
|
|
#define MICROPY_HW_HAS_MMA7660 (0)
|
|
|
|
|
#define MICROPY_HW_HAS_LIS3DSH (0)
|
|
|
|
|
#define MICROPY_HW_HAS_LCD (0)
|
|
|
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
|
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
|
|
|
#define MICROPY_HW_ENABLE_TIMER (1)
|
|
|
|
|
#define MICROPY_HW_ENABLE_SERVO (0)
|
|
|
|
|
#define MICROPY_HW_ENABLE_DAC (0)
|
|
|
|
|
#define MICROPY_HW_ENABLE_CAN (1)
|
|
|
|
|
|
|
|
|
|
// HSE is 8MHz
|
|
|
|
|
#define MICROPY_HW_CLK_PLLM (8)
|
|
|
|
|
#define MICROPY_HW_CLK_PLLN (336)
|
|
|
|
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
|
|
|
|
|
#define MICROPY_HW_CLK_PLLQ (7)
|
|
|
|
|
|
|
|
|
|
// UART config
|
|
|
|
|
#define MICROPY_HW_UART1_PORT (GPIOA)
|
|
|
|
|
#define MICROPY_HW_UART1_PINS (GPIO_PIN_9 | GPIO_PIN_10)
|
|
|
|
|
#define MICROPY_HW_UART2_PORT (GPIOD)
|
|
|
|
|
#define MICROPY_HW_UART2_PINS (GPIO_PIN_8 | GPIO_PIN_9)
|
|
|
|
|
|
|
|
|
|
// I2C busses
|
2016-08-01 10:47:39 +01:00
|
|
|
#define MICROPY_HW_I2C3_SCL (pin_A8)
|
|
|
|
|
#define MICROPY_HW_I2C3_SDA (pin_C9)
|
2015-11-24 13:35:24 +00:00
|
|
|
|
2015-12-08 14:41:47 +00:00
|
|
|
// SPI busses
|
|
|
|
|
//#define MICROPY_HW_SPI1_NSS (pin_A4)
|
|
|
|
|
//#define MICROPY_HW_SPI1_SCK (pin_A5)
|
|
|
|
|
//#define MICROPY_HW_SPI1_MISO (pin_A6)
|
|
|
|
|
//#define MICROPY_HW_SPI1_MOSI (pin_A7)
|
|
|
|
|
#if defined(USE_USB_HS_IN_FS)
|
|
|
|
|
// The HS USB uses B14 & B15 for D- and D+
|
|
|
|
|
#else
|
|
|
|
|
#define MICROPY_HW_SPI2_NSS (pin_B12)
|
|
|
|
|
#define MICROPY_HW_SPI2_SCK (pin_B13)
|
|
|
|
|
#define MICROPY_HW_SPI2_MISO (pin_B14)
|
|
|
|
|
#define MICROPY_HW_SPI2_MOSI (pin_B15)
|
|
|
|
|
#endif
|
|
|
|
|
//#define MICROPY_HW_SPI4_NSS (pin_E11)
|
|
|
|
|
//#define MICROPY_HW_SPI4_SCK (pin_E12)
|
|
|
|
|
//#define MICROPY_HW_SPI4_MISO (pin_E13)
|
|
|
|
|
//#define MICROPY_HW_SPI4_MOSI (pin_E14)
|
|
|
|
|
#define MICROPY_HW_SPI5_NSS (pin_F6)
|
|
|
|
|
#define MICROPY_HW_SPI5_SCK (pin_F7)
|
|
|
|
|
#define MICROPY_HW_SPI5_MISO (pin_F8)
|
|
|
|
|
#define MICROPY_HW_SPI5_MOSI (pin_F9)
|
|
|
|
|
//#define MICROPY_HW_SPI6_NSS (pin_G8)
|
|
|
|
|
//#define MICROPY_HW_SPI6_SCK (pin_G13)
|
|
|
|
|
//#define MICROPY_HW_SPI6_MISO (pin_G12)
|
|
|
|
|
//#define MICROPY_HW_SPI6_MOSI (pin_G14)
|
|
|
|
|
|
2015-11-24 13:35:24 +00:00
|
|
|
// USRSW is pulled low. Pressing the button makes the input go high.
|
|
|
|
|
#define MICROPY_HW_USRSW_PIN (pin_A0)
|
|
|
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
|
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
|
|
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
|
|
|
|
|
|
|
|
|
// LEDs
|
|
|
|
|
#define MICROPY_HW_LED1 (pin_G14) // red
|
|
|
|
|
#define MICROPY_HW_LED2 (pin_G13) // green
|
|
|
|
|
#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP)
|
|
|
|
|
#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask)
|
|
|
|
|
#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask)
|
|
|
|
|
|
|
|
|
|
// USB config
|
|
|
|
|
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_B13)
|
|
|
|
|
#define MICROPY_HW_USB_OTG_ID_PIN (pin_B12)
|
