mirrors
/
micropython
mirror of https://github.com/micropython/micropython.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
micropython/stmhal/boards/STM32F4DISC/mpconfigboard.h

74 lines
2.6 KiB
C
Raw Normal View History

Initial checkin with STM HAL This compiles and links, but hasn't been tested on a board yet and even if it was run, it doesn't currently do anything.
2014-03-12 06:55:41 +00:00
#define STM32F4DISC
#define MICROPY_HW_BOARD_NAME "F4DISC"
Change MCU name config micro
2014-06-26 23:35:53 +01:00
#define MICROPY_HW_MCU_NAME "STM32F407"
Initial checkin with STM HAL This compiles and links, but hasn't been tested on a board yet and even if it was run, it doesn't currently do anything.
2014-03-12 06:55:41 +00:00
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_SDCARD (0)
#define MICROPY_HW_HAS_MMA7660 (0)
#define MICROPY_HW_HAS_LIS3DSH (1)
#define MICROPY_HW_HAS_LCD (0)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_TIMER (1)
#define MICROPY_HW_ENABLE_SERVO (0)
stmhal: Enable DAC on STM32F4DISC. Addresses issue #987.
2014-11-25 11:42:26 +00:00
#define MICROPY_HW_ENABLE_DAC (1)
stmhal: Add config option to disable/enable CAN driver.
2014-10-05 18:05:26 +01:00
#define MICROPY_HW_ENABLE_CAN (1)
Initial checkin with STM HAL This compiles and links, but hasn't been tested on a board yet and even if it was run, it doesn't currently do anything.
2014-03-12 06:55:41 +00:00
stmhal: Make HSE PLL parameters configurable per board.
2015-04-18 15:30:04 +01:00
// HSE is 8MHz
#define MICROPY_HW_CLK_PLLM (8)
#define MICROPY_HW_CLK_PLLN (336)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (7)
stmhal: Allow to configure UART pins completely via mpconfigboard.h.
2015-05-02 17:31:39 +01:00
// UART config
#define MICROPY_HW_UART1_PORT (GPIOA)
#define MICROPY_HW_UART1_PINS (GPIO_PIN_9 | GPIO_PIN_10)
#define MICROPY_HW_UART2_PORT (GPIOA)
#define MICROPY_HW_UART2_PINS (GPIO_PIN_2 | GPIO_PIN_3)
#define MICROPY_HW_UART2_RTS (GPIO_PIN_1)
#define MICROPY_HW_UART2_CTS (GPIO_PIN_0)
#define MICROPY_HW_UART3_PORT (GPIOD)
#define MICROPY_HW_UART3_PINS (GPIO_PIN_8 | GPIO_PIN_9)
#define MICROPY_HW_UART3_RTS (GPIO_PIN_12)
#define MICROPY_HW_UART3_CTS (GPIO_PIN_11)
#define MICROPY_HW_UART4_PORT (GPIOA)
#define MICROPY_HW_UART4_PINS (GPIO_PIN_0 | GPIO_PIN_1)
#define MICROPY_HW_UART6_PORT (GPIOC)
#define MICROPY_HW_UART6_PINS (GPIO_PIN_6 | GPIO_PIN_7)
stmhal: Make I2C busses and their pins configurable in mpconfigboard.h.
2015-04-18 16:12:57 +01:00
// I2C busses
#define MICROPY_HW_I2C1_SCL (pin_B6)
#define MICROPY_HW_I2C1_SDA (pin_B7)
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)
stmhal: For SPI config, use HW_SPIx_SCK instead of HW_ENABLE_SPIx. Previously, SPI was configured by a board defining MICROPY_HW_ENABLE_SPIx to 0 or 1. Now, the board should define MICROPY_HW_SPIx_SCK, MISO, MOSI and NSS. This makes it the same as how I2C is configured.
2015-12-12 15:02:02 +00:00
// SPI busses
#define MICROPY_HW_SPI1_NSS (pin_A4)
#define MICROPY_HW_SPI1_SCK (pin_A5)
#define MICROPY_HW_SPI1_MISO (pin_A6)
#define MICROPY_HW_SPI1_MOSI (pin_A7)
#define MICROPY_HW_SPI2_NSS (pin_B12)
#define MICROPY_HW_SPI2_SCK (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
Initial checkin with STM HAL This compiles and links, but hasn't been tested on a board yet and even if it was run, it doesn't currently do anything.
2014-03-12 06:55:41 +00:00
// USRSW is pulled low. Pressing the button makes the input go high.
stmhal: Unify naming of HW config; make SD detect configurable. All board config macros now begin with MICROPY_HW_. Renamed PYBv10 to PYBV10, since macros should be all uppercase. Made SDCARD_DETECT configurable in mpconfigport.h, so that the SD detect pin can be easily configured.
2014-03-30 12:30:35 +01:00
#define MICROPY_HW_USRSW_PIN (pin_A0)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED (1)
Initial checkin with STM HAL This compiles and links, but hasn't been tested on a board yet and even if it was run, it doesn't currently do anything.
2014-03-12 06:55:41 +00:00
stmhal: Unify naming of HW config; make SD detect configurable. All board config macros now begin with MICROPY_HW_. Renamed PYBv10 to PYBV10, since macros should be all uppercase. Made SDCARD_DETECT configurable in mpconfigport.h, so that the SD detect pin can be easily configured.
2014-03-30 12:30:35 +01:00
// LEDs
#define MICROPY_HW_LED1 (pin_D14) // red
#define MICROPY_HW_LED2 (pin_D12) // green
#define MICROPY_HW_LED3 (pin_D13) // orange
#define MICROPY_HW_LED4 (pin_D15) // blue
#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP)
#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask)
#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask)
stmhal: Add MICROPY_HW_USB_VBUS_DETECT_PIN option, for boards without it Since all currently supported boards use pin A9 for this function, the value of the macro MICROPY_HW_USB_VBUS_DETECT_PIN is not actually used, just the fact that it is defined. Addresses issue #1048.
2015-01-07 23:54:57 +00:00
stmhal: Add MICROPY_HW_USB_OTG_ID_PIN config, set for relevant boards. This config option is for the USB OTG pin, pin A10. This is used on some boards but not others. Eg PYBv3 uses PA10 for LED(2), so it shouldn't be used for OTG ID (actually PA10 is multiplexed on this board, but defaults to LED(2)). Partially addresses issue #1059.
2015-01-12 16:13:29 +00:00
// USB config
stmhal: Add MICROPY_HW_USB_VBUS_DETECT_PIN option, for boards without it Since all currently supported boards use pin A9 for this function, the value of the macro MICROPY_HW_USB_VBUS_DETECT_PIN is not actually used, just the fact that it is defined. Addresses issue #1048.
2015-01-07 23:54:57 +00:00
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
stmhal: Add MICROPY_HW_USB_OTG_ID_PIN config, set for relevant boards. This config option is for the USB OTG pin, pin A10. This is used on some boards but not others. Eg PYBv3 uses PA10 for LED(2), so it shouldn't be used for OTG ID (actually PA10 is multiplexed on this board, but defaults to LED(2)). Partially addresses issue #1059.
2015-01-12 16:13:29 +00:00
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)