Merge pull request #852 from techno/staccel_LIS3DSH

Add LIS3DSH accelometer support to staccel.py

stmhal/boards/STM32F4DISC/staccel.py

@@ -1,7 +1,6 @@
 """
 Driver for accelerometer on STM32F4 Discover board.
 
-Assumes it's a LIS302DL MEMS device.
 Sets accelerometer range at +-2g.
 Returns list containing X,Y,Z axis acceleration values in 'g' units (9.8m/s^2).
 
@@ -20,28 +19,46 @@ from pyb import SPI
 
 READWRITE_CMD = const(0x80) 
 MULTIPLEBYTE_CMD = const(0x40)
-LIS302DL_WHO_AM_I_ADDR = const(0x0f)
+WHO_AM_I_ADDR = const(0x0f)
+OUT_X_ADDR = const(0x29)
+OUT_Y_ADDR = const(0x2b)
+OUT_Z_ADDR = const(0x2d)
+OUT_T_ADDR = const(0x0c)
+
 LIS302DL_WHO_AM_I_VAL = const(0x3b)
 LIS302DL_CTRL_REG1_ADDR = const(0x20)
-LIS302DL_OUT_X = const(0x29)
-LIS302DL_OUT_Y = const(0x2b)
-LIS302DL_OUT_Z = const(0x2d)
 # Configuration for 100Hz sampling rate, +-2g range
 LIS302DL_CONF = const(0b01000111)
 
-def convert_raw_to_g(x):
-    if x & 0x80:
-        x = x - 256
-    return x * 18 / 1000
+LIS3DSH_WHO_AM_I_VAL = const(0x3f)
+LIS3DSH_CTRL_REG4_ADDR = const(0x20)
+LIS3DSH_CTRL_REG5_ADDR = const(0x24)
+# Configuration for 100Hz sampling rate, +-2g range
+LIS3DSH_CTRL_REG4_CONF = const(0b01100111)
+LIS3DSH_CTRL_REG5_CONF = const(0b00000000)
 
 class STAccel:
     def __init__(self):
         self.cs_pin = Pin('PE3', Pin.OUT_PP, Pin.PULL_NONE)
         self.cs_pin.high()
         self.spi = SPI(1, SPI.MASTER, baudrate=328125, polarity=0, phase=1, bits=8)
-        self.write_bytes(LIS302DL_CTRL_REG1_ADDR, bytearray([LIS302DL_CONF]))
-        if self.read_id() != LIS302DL_WHO_AM_I_VAL:
-            raise Exception('LIS302DL accelerometer not present')
+
+        self.who_am_i = self.read_id()
+
+        if self.who_am_i == LIS302DL_WHO_AM_I_VAL:
+            self.write_bytes(LIS302DL_CTRL_REG1_ADDR, bytearray([LIS302DL_CONF]))
+            self.sensitivity = 18
+        elif self.who_am_i == LIS3DSH_WHO_AM_I_VAL:
+            self.write_bytes(LIS3DSH_CTRL_REG4_ADDR, bytearray([LIS3DSH_CTRL_REG4_CONF]))
+            self.write_bytes(LIS3DSH_CTRL_REG5_ADDR, bytearray([LIS3DSH_CTRL_REG5_CONF]))
+            self.sensitivity = 0.06 * 256
+        else:
+            raise Exception('LIS302DL or LIS3DSH accelerometer not present')
+
+    def convert_raw_to_g(self, x):
+        if x & 0x80:
+            x = x - 256
+        return x * self.sensitivity / 1000
 
     def read_bytes(self, addr, nbytes):
         if nbytes > 1:
@@ -65,19 +82,16 @@ class STAccel:
         self.cs_pin.high()
 
     def read_id(self):
-        return self.read_bytes(LIS302DL_WHO_AM_I_ADDR, 1)[0]
+        return self.read_bytes(WHO_AM_I_ADDR, 1)[0]
 
     def x(self):
-        return convert_raw_to_g(self.read_bytes(LIS302DL_OUT_X, 1)[0])
+        return self.convert_raw_to_g(self.read_bytes(OUT_X_ADDR, 1)[0])
 
     def y(self):
-        return convert_raw_to_g(self.read_bytes(LIS302DL_OUT_Y, 1)[0])
+        return self.convert_raw_to_g(self.read_bytes(OUT_Y_ADDR, 1)[0])
 
     def z(self):
-        return convert_raw_to_g(self.read_bytes(LIS302DL_OUT_Z, 1)[0])
+        return self.convert_raw_to_g(self.read_bytes(OUT_Z_ADDR, 1)[0])
 
     def xyz(self):
-        val = self.read_bytes(LIS302DL_OUT_X, 5)
-        return [convert_raw_to_g(val[0]),
-                convert_raw_to_g(val[2]),
-                convert_raw_to_g(val[4])]
+        return (self.x(), self.y(), self.z())