The amount of free IRAM in ESP32 SPIRAM builds is very small and went over
the limit due to commit 30b0ee34d3. This
commit enables further optimisations to reduce IRAM usage.
Signed-off-by: Damien George <damien@micropython.org>
Also shrinks the "prefer internal" threshold to 8KB, any allocation larger
than this will try PSRAM first.
Change the mbedTLS config to use regular malloc() as well, instead of
internal only. The default is set to internal-only due to to potential
physical security issue of readout via PSRAM on the original ESP32.
However, as MicroPython runs from plaintext flash and all other context is
in the MP heap of PSRAM then it's hard to see how worsens physical security
for MP.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This commit updates the esp32 port to work exclusively with ESP-IDF v5.
IDF v5 is needed for some of the newer ESP32 SoCs to work, and it also
cleans up a lot of the inconsistencies between existing SoCs (eg S2, S3,
and C3).
Support for IDF v4 is dropped because it's a lot of effort to maintain both
versions at the same time.
The following components have been verified to work on the various SoCs:
ESP32 ESP32-S2 ESP32-S3 ESP32-C3
build pass pass pass pass
SPIRAM pass pass pass N/A
REPL (UART) pass pass pass pass
REPL (USB) N/A pass pass N/A
filesystem pass pass pass pass
GPIO pass pass pass pass
SPI pass pass pass pass
I2C pass pass pass pass
PWM pass pass pass pass
ADC pass pass pass pass
WiFi STA pass pass pass pass
WiFi AP pass pass pass pass
BLE pass N/A pass pass
ETH pass -- -- --
PPP pass pass pass --
sockets pass pass pass pass
SSL pass ENOMEM pass pass
RMT pass pass pass pass
NeoPixel pass pass pass pass
I2S pass pass pass N/A
ESPNow pass pass pass pass
ULP-FSM pass pass pass N/A
SDCard pass N/A N/A pass
WDT pass pass pass pass
Signed-off-by: Damien George <damien@micropython.org>
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds support for a second supported hash (currently set to the
4.0-beta1 tag). When this hash is detected, the relevant changes are
applied.
This allows to start using v4 features (e.g. BLE with Nimble), and also
start doing testing, while still supporting the original, stable, v3.3 IDF.
Note: this feature is experimental, not well tested, and network.LAN and
network.PPP are currently unsupported.
Replaces the `SDKCONFIG` makefile variable with `BOARD`. Defaults to
BOARD=GENERIC. spiram can be enabled with `BOARD=GENERIC_SPIRAM`
Add example definition for TINYPICO, currently identical to GENERIC_SPIRAM
but with custom board/SoC names for the uPy banner.
Auto-detection of the crystal frequency is convenient and allows for a
single binary for many different boards. But it can be unreliable in
certain situations so in production, for a given board, it's recommended to
configure the correct fixed frequency.
Configuration for the build is now specified using sdkconfig rather than
sdkconfig.h, which allows for much easier configuration with defaults from
the ESP IDF automatically applied. sdkconfig.h is generated using the new
ESP IDF kconfig_new tool written in Python. Custom configuration for a
particular ESP32 board can be specified via the make variable SDKCONFIG.
The esp32.common.ld file is also now generated using the standard ESP IDF
ldgen.py tool.
Damien George
Angus Gratton
Jim Mussared
Damien George