This fixes the case where e.g.
struct foo_t {
mp_obj_t x;
uint16_t y;
char buf[];
};
will have `sizeof(struct foo_t)==8`, but `offsetof(struct foo_t, buf)==6`.
When computing the size to allocate for `m_new_obj_var` we need to use
offsetof to avoid over-allocating. This is important especially when it
might cause it to spill over into another GC block.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Instead of being an explicit field, it's now a slot like all the other
methods.
This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The goal here is to remove a slot (making way to turn make_new into a slot)
as well as reduce code size by the ~40 references to mp_identity_getiter
and mp_stream_unbuffered_iter.
This introduces two new type flags:
- MP_TYPE_FLAG_ITER_IS_ITERNEXT: This means that the "iter" slot in the
type is "iternext", and should use the identity getiter.
- MP_TYPE_FLAG_ITER_IS_CUSTOM: This means that the "iter" slot is a pointer
to a mp_getiter_iternext_custom_t instance, which then defines both
getiter and iternext.
And a third flag that is the OR of both, MP_TYPE_FLAG_ITER_IS_STREAM: This
means that the type should use the identity getiter, and
mp_stream_unbuffered_iter as iternext.
Finally, MP_TYPE_FLAG_ITER_IS_GETITER is defined as a no-op flag to give
the default case where "iter" is "getiter".
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Rather than reserving a full 12-slot mp_obj_type_t, reserve enough room for
seven and cast as necessary.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
In all cases other than where you have a native base with a protocol, it
now fits into 4 GC blocks (like it did before the slots representation).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The empty tuple is usually a constant object, but named tuples must be
allocated to allow modification. Added explicit allocation to fix this.
Also added a regression test to verify creating an empty named tuple works.
Fixes issue #7870.
Signed-off-by: Lars Haulin <lars.haulin@gmail.com>
This introduces a new option, MICROPY_ERROR_REPORTING_NONE, which
completely disables all error messages. To be used in cases where
MicroPython needs to fit in very limited systems.
Signed-off-by: Damien George <damien@micropython.org>
Note: the uncrustify configuration is explicitly set to 'add' instead of
'force' in order not to alter the comments which use extra spaces after //
as a means of indenting text for clarity.
Instead of compiler-level if-logic. This is necessary to know what error
strings are included in the build at the preprocessor stage, so that string
compression can be implemented.
Both bool and namedtuple will check against other types for equality; int,
float and complex for bool, and tuple for namedtuple. So to make them work
after the recent commit 3aab54bf43 they would
need MP_TYPE_FLAG_NEEDS_FULL_EQ_TEST set. But that makes all bool and
namedtuple equality checks less efficient because mp_obj_equal_not_equal()
could no longer short-cut x==x, and would need to try __ne__. To improve
this, this commit splits the MP_TYPE_FLAG_NEEDS_FULL_EQ_TEST flags into 3
separate flags to give types more fine-grained control over how their
equality behaves. These new flags are then used to fix bool and namedtuple
equality.
Fixes issue #5615 and #5620.
These macros could in principle be (inline) functions so it makes sense to
have them lower case, to match the other C API functions.
The remaining macros that are upper case are:
- MP_OBJ_TO_PTR, MP_OBJ_FROM_PTR
- MP_OBJ_NEW_SMALL_INT, MP_OBJ_SMALL_INT_VALUE
- MP_OBJ_NEW_QSTR, MP_OBJ_QSTR_VALUE
- MP_OBJ_FUN_MAKE_SIG
- MP_DECLARE_CONST_xxx
- MP_DEFINE_CONST_xxx
These must remain macros because they are used when defining const data (at
least, MP_OBJ_NEW_SMALL_INT is so it makes sense to have
MP_OBJ_SMALL_INT_VALUE also a macro).
For those macros that have been made lower case, compatibility macros are
provided for the old names so that users do not need to change their code
immediately.
Header files that are considered internal to the py core and should not
normally be included directly are:
py/nlr.h - internal nlr configuration and declarations
py/bc0.h - contains bytecode macro definitions
py/runtime0.h - contains basic runtime enums
Instead, the top-level header files to include are one of:
py/obj.h - includes runtime0.h and defines everything to use the
mp_obj_t type
py/runtime.h - includes mpstate.h and hence nlr.h, obj.h, runtime0.h,
and defines everything to use the general runtime support functions
Additional, specific headers (eg py/objlist.h) can be included if needed.
Prior to this patch there were 2 paths for creating the namedtuple, one for
when no keyword args were passed, and one when there were keyword args.
And alloca was used in the keyword-arg path to temporarily create the array
of elements for the namedtuple, which would then be copied to a
heap-allocated object (the namedtuple itself).
This patch simplifies the code by combining the no-keyword and keyword
paths, and removing the need for the alloca by constructing the namedtuple
on the heap before populating it.
Heap usage in unchanged, stack usage is reduced, use of alloca is removed,
and code size is not increased and is actually reduced by between 20-30
bytes for most ports.
The common cases for inheritance are 0 or 1 parent types, for both built-in
types (eg built-in exceptions) as well as user defined types. So it makes
sense to optimise the case of 1 parent type by storing just the type and
not a tuple of 1 value (that value being the single parent type).
This patch makes such an optimisation. Even though there is a bit more
code to handle the two cases (either a single type or a tuple with 2 or
more values) it helps reduce overall code size because it eliminates the
need to create a static tuple to hold single parents (eg for the built-in
exceptions). It also helps reduce RAM usage for user defined types that
only derive from a single parent.
Changes in code size (in bytes) due to this patch:
bare-arm: -16
minimal (x86): -176
unix (x86-64): -320
unix nanbox: -384
stmhal: -64
cc3200: -32
esp8266: -108
This patch changes mp_uint_t to size_t for the len argument of the
following public facing C functions:
mp_obj_tuple_get
mp_obj_list_get
mp_obj_get_array
These functions take a pointer to the len argument (to be filled in by the
function) and callers of these functions should update their code so the
type of len is changed to size_t. For ports that don't use nan-boxing
there should be no change in generate code because the size of the type
remains the same (word sized), and in a lot of cases there won't even be a
compiler warning if the type remains as mp_uint_t.
The reason for this change is to standardise on the use of size_t for
variables that count memory (or memory related) sizes/lengths. It helps
builds that use nan-boxing.
Passing an mp_uint_t to a %d printf format is incorrect for builds where
mp_uint_t is larger than word size (eg a nanboxing build). This patch
adds some simple casting to int in these cases.
The first argument to the type.make_new method is naturally a uPy type,
and all uses of this argument cast it directly to a pointer to a type
structure. So it makes sense to just have it a pointer to a type from
the very beginning (and a const pointer at that). This patch makes
such a change, and removes all unnecessary casting to/from mp_obj_t.
This patch changes the type signature of .make_new and .call object method
slots to use size_t for n_args and n_kw (was mp_uint_t. Makes code more
efficient when mp_uint_t is larger than a machine word. Doesn't affect
ports when size_t and mp_uint_t have the same size.
This allows the mp_obj_t type to be configured to something other than a
pointer-sized primitive type.
This patch also includes additional changes to allow the code to compile
when sizeof(mp_uint_t) != sizeof(void*), such as using size_t instead of
mp_uint_t, and various casts.
Previous to this patch the printing mechanism was a bit of a tangled
mess. This patch attempts to consolidate printing into one interface.
All (non-debug) printing now uses the mp_print* family of functions,
mainly mp_printf. All these functions take an mp_print_t structure as
their first argument, and this structure defines the printing backend
through the "print_strn" function of said structure.
Printing from the uPy core can reach the platform-defined print code via
two paths: either through mp_sys_stdout_obj (defined pert port) in
conjunction with mp_stream_write; or through the mp_plat_print structure
which uses the MP_PLAT_PRINT_STRN macro to define how string are printed
on the platform. The former is only used when MICROPY_PY_IO is defined.
With this new scheme printing is generally more efficient (less layers
to go through, less arguments to pass), and, given an mp_print_t*
structure, one can call mp_print_str for efficiency instead of
mp_printf("%s", ...). Code size is also reduced by around 200 bytes on
Thumb2 archs.
This simplifies the API for objects and reduces code size (by around 400
bytes on Thumb2, and around 2k on x86). Performance impact was measured
with Pystone score, but change was barely noticeable.
- namedtuple was wrongly using MP_OBJ_QSTR_VALUE instead of mp_obj_str_get_qstr,
so when passed a non-interned string it would segfault; fix this by using mp_obj_str_get_qstr
- store the namedtuple field names as qstrs so it is not needed to use mp_obj_str_get_qstr
everytime the field name has to be accessed. This also slighty increases performance when
fetching attributes
We are not word-for-word compatible with CPython exceptions, so we are
free to make them short but informative in order to reduce code size.
Also, try to make messages the same as existing ones where possible.
Jim Mussared
Lars Haulin
Damien George
stijn
Damien George
Paul Sokolovsky
Alexander Steffen
Antonin ENFRUN
stijn