This improves (decreases) the latency on stdin, on SoCs with built-in USB
and using TinyUSB, like S2 and S3.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
CONFIG_USB_OTG_SUPPORTED is automatically set by the ESP-IDF when the chip
supports USB-OTG, which is the case for the ESP32-S2 and ESP32-S3.
When trying to use the JTAG console with these chips, it would not work
because our USB implementation will take over control over the USB port,
breaking the JTAG console in the process.
Thus, when the board is configured to use the JTAG console, we should not
enable our USB console support.
Additionally, this change also frees up UART0 when an USB-based console is
configured, since there's no reason to prevent (re)configuration of UART0
for other uses in that case.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
This commit updates the esp32 port to work exclusively with ESP-IDF v5.
IDF v5 is needed for some of the newer ESP32 SoCs to work, and it also
cleans up a lot of the inconsistencies between existing SoCs (eg S2, S3,
and C3).
Support for IDF v4 is dropped because it's a lot of effort to maintain both
versions at the same time.
The following components have been verified to work on the various SoCs:
ESP32 ESP32-S2 ESP32-S3 ESP32-C3
build pass pass pass pass
SPIRAM pass pass pass N/A
REPL (UART) pass pass pass pass
REPL (USB) N/A pass pass N/A
filesystem pass pass pass pass
GPIO pass pass pass pass
SPI pass pass pass pass
I2C pass pass pass pass
PWM pass pass pass pass
ADC pass pass pass pass
WiFi STA pass pass pass pass
WiFi AP pass pass pass pass
BLE pass N/A pass pass
ETH pass -- -- --
PPP pass pass pass --
sockets pass pass pass pass
SSL pass ENOMEM pass pass
RMT pass pass pass pass
NeoPixel pass pass pass pass
I2S pass pass pass N/A
ESPNow pass pass pass pass
ULP-FSM pass pass pass N/A
SDCard pass N/A N/A pass
WDT pass pass pass pass
Signed-off-by: Damien George <damien@micropython.org>
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This was introduced by 35fb90bd57, but
it is much simpler and essentially the same to just use
`tud_cdc_n_connected()`.
The only difference is that tud_cdc_n_connected() only checks for DTR,
but this is correct anyway: DTR indicates device presence, RTS indicates
that the host wants to receive data.
Signed-off-by: Damien Tournoud <damien@platform.sh>
If USB CDC is connected and the board sends data, but the host does not
receive the data, the device locks up. This is fixed in this commit by
having a timeout of 500ms, after which time the transmission is skipped.
Following on from ba940250a5, the change here
makes output about 15 times faster (now up to about 550 kbytes/sec).
tinyusb_cdcacm_write_queue will return the number of bytes written, so
there's no need to use tud_cdc_n_write_available.
Signed-off-by: Damien George <damien@micropython.org>
This callback allows detecting if there is a USB host connected to the CDC
or not, in which case the stdout_tx should skip CDC TX writing and
flushing or the system will block.
Fixes issue #7820.
Andrew Leech
Daniël van de Giessen
Luca Burelli
Damien George
Damien Tournoud
robert-hh
Seon Rozenblum