For builds with DEBUG=1 and MICROPY_HW_ENABLE_UART_REPL=1, calling
stdio_init_all() in main() detaches the UART input from REPL. This change
suppresses calling stdio_init_all() then.
Previously, setting MICROPY_HW_ENABLE_USBDEV to 0 caused build errors. The
change affects the nrf and samd ports as well, so MICROPY_HW_ENABLE_USBDEV
had to be explicitly enabled there.
The configuration options MICROPY_HW_ENABLE_USBDEV and
MICROPY_HW_ENABLE_UART_REPL are independent, and can be enabled or disabled
by a board.
Signed-off-by: Damien George <damien@micropython.org>
Changes in this commit:
- Add the timeout and timeout_char keyword options.
- Make uart.read() non-blocking.
- Add uart.any().
- Add ioctl MP_STREAM_POLL handling.
- Change uart.write() into non-busy waiting. uart.write() still waits until
all data has been sent, but calls MICROPY_EVENT_POLL_HOOK while waiting.
uart.write() uses DMA for transfer. One option would be to add a small
local buffer, such that transfers up to the size of the buffer could be
done without waiting.
- As a side effect to the change of uart.write(), uart.txdone() and ioctl
flush now report/wait correctly for the end of transmission.
- Change machine_hard_uart_buf_t in machine_hard_uart_obj_t to an instance
of that struct, rather than a pointer to one.
Even if boards do not have a clock crystal. In that case, the clock
quality will be very poor.
Always having machine.RTC means that the date/time can be set in a way that
is consistent with other ports.
This commit also removes the special code in modutime.c for devices without
the RTC class.
Signed-off-by: Damien George <damien@micropython.org>
These have the same frequency, but can have different duty cycle and
polarity.
pwm.deinit() stops all channels of a module, but does not release the
module. pwm.init() without arguments restarts all outputs.
Using extmod/machine_pwm.c for the Python bindings and the existing
softpwm.c driver, by just adding the interface.
Properties:
- Frequency range 1-3906 Hz.
- All PWM outputs run at the same frequency but can have different duty
cycles.
- Limited to the P0.x pins.
Since it uses the existing softpwm.c mechanism, it will be affected by
playing music with the music class.
This is a breaking change, making the hardware PWM on the nrf port
compatible with the other ports providing machine.PWM.
Frequency range 4Hz - ~5.4 MHz. The base clock range is 125kHz to 16 MHz,
and the divider range is 3 - 32767.
The hardware supports up to four outputs per PWM device with different duty
cycles, but only one output is (and was) supported.
Borrowing an idea from the mimxrt port (also stm32 port): in the loader
input file memmap_mp.ld calculate __GcHeapStart and __GcHeapEnd as the
unused RAM. Then in main.c use these addresses as arguments to gc_init().
The benefits of this change are:
1) When libraries are added or removed in the future changing BSS usage,
main.c's sizing of the GC heap does not need to be changed.
2) Currently these changes make the GC area about 30 KBytes larger, eg on
PICO_W the GC heap increases from 166016 to 192448 bytes. Without that
change this RAM would never get used.
3) If someone wants to disable one or more SRAM blocks on the RP2040 to
reduce power consumption it will be easy: just change the MEMORY section
in memmap_mp.ld. For instance to not use SRAM2 and SRAM3 change it to:
MEMORY
{
FLASH(rx) : ORIGIN = 0x10000000, LENGTH = 2048k
RAM(rwx) : ORIGIN = 0x21000000, LENGTH = 128k
SCRATCH_X(rwx) : ORIGIN = 0x20040000, LENGTH = 4k
SCRATCH_Y(rwx) : ORIGIN = 0x20041000, LENGTH = 4k
}
Then to turn off clocks for SRAM2 and SRAM3 from MicroPython, set the
appropriate bits in WAKE_EN0 and SLEEP_EN0.
Tested by running the firmware.uf2 file on PICO_W and displaying
micropython.mem_info(). Confirmed GC total size approximately matched the
size calculated by the loader.
Signed-off-by: cpottle9 <cpottle9@outlook.com>
This function seems to work fine in multi-core applications now.
The delay is now in units of microseconds instead of depending on the clock
speed, and is adjustable by board configuration headers.
Also added documentation.
These changes allow the firmware to support both the REV-1 and REV-2
versions of the board:
- Freeze the new device drivers used in REV-2.
- Add a board-level module that abstracts the IMU chipset.
Changes are:
- Freeze micropython-lib time module to get strftime.
- Reserve the last 1MB of QSPI flash for (optional) WiFi firmware storage.
- Disable SD card mount on boot.
- Enable high-speed BLE firmware download.
Damien George
robert-hh
iabdalkader
pmendham
IhorNehrutsa
Christian Clauss
cpottle9
David Grayson
Tomofumi Inoue
Andrew Leech