It should be up to the NIC itself to decide if the network interface is
removed upon soft reset. Some NICs can keep the interface up over a soft
reset, which improves usability of the network.
Pins with multiple alt-funcs for the same peripheral (eg USART_CTS_NSS)
need to be split into individual alt-funcs for make-pins.py to work
correctly.
This patch changes the following:
- Split `..._CTS_NSS` into `..._CTS/..._NSS`
- Split `..._RTS_DE` into `..._RTS/..._DE`
- Split `JTDO_SWO` into `JTDO/TRACESWO` for consistency
- Fixed `TRACECK` to `TRACECLK` for consistency
If no block devices are defined by a board then storage support will be
disabled. This means there is no filesystem provided by either the
internal flash or external SPI flash. But the VFS system can still be
enabled and filesystems provided on external devices like an SD card.
Mboot is a custom bootloader for STM32 MCUs. It can provide a USB DFU
interface on either the FS or HS peripherals, as well as a custom I2C
bootloader interface.
These files provide no additional information, all the version and license
information is captured in the relevant files in these subdirectories.
Thanks to @JoeSc for the original patch.
This patch allows to use lwIP as the implementation of the usocket module,
instead of the existing socket-multiplexer that delegates the entire TCP/IP
layer to the NIC itself.
This is disabled by default, and enabled by defining MICROPY_PY_LWIP to 1.
When enabled, the lwIP TCP/IP stack will be included in the build with
default settings for memory usage and performance (see
lwip_inc/lwipopts.h). It is then up to a particular NIC to register itself
with lwIP using the standard lwIP netif API.
This patch makes it so that UART(0) can by dynamically attached to and
detached from the REPL by using the uos.dupterm function. Since WebREPL
uses dupterm slot 0 the UART uses dupterm slot 1 (a slot which is newly
introduced by this patch). UART(0) must now be attached manually in
boot.py (or otherwise) and inisetup.py is changed to provide code to do
this. For example, to attach use:
import uos, machine
uart = machine.UART(0, 115200)
uos.dupterm(uart, 1)
and to detach use:
uos.dupterm(None, 1)
When attached, all incoming chars on UART(0) go straight to stdin so
uart.read() will always return None. Use sys.stdin.read() if it's needed
to read characters from the UART(0) while it's also used for the REPL (or
detach, read, then reattach). When detached the UART(0) can be used for
other purposes.
If there are no objects in any of the dupterm slots when the REPL is
started (on hard or soft reset) then UART(0) is automatically attached.
Without this, the only way to recover a board without a REPL would be to
completely erase and reflash (which would install the default boot.py which
attaches the REPL).
Add CONFIG_NET_DHCPV4, which, after
https://github.com/zephyrproject-rtos/zephyr/pull/5750 works as follows:
static addresses are configured after boot, and DHCP requests are sent
at the same time. If valid DHCP reply is received, it overrides static
addresses.
This setup works out of the box for both direct connection to a
workstation (DHCP server usually is not available) and for connection
to a router (DHCP is available and required).
This patch adds the configuration MICROPY_HW_USB_ENABLE_CDC2 which enables
a new USB device configuration at runtime: VCP+VCP+MSC. It will give two
independent VCP interfaces available via pyb.USB_VCP(0) and pyb.USB_VCP(1).
The first one is the usual one and has the REPL on it. The second one is
available for general use.
This configuration is disabled by default because if the mode is not used
then it takes up about 2200 bytes of RAM. Also, F4 MCUs can't support this
mode on their USB FS peripheral (eg PYBv1.x) because they don't have enough
endpoints. The USB HS peripheral of an F4 supports it, as well as both the
USB FS and USB HS peripherals of F7 MCUs.
Damien George
rolandvs
Nick Moore
Daniel Shaulov
Paul Sokolovsky
Tobias Badertscher
Ryan Shaw