For now, this implements the functionality required for esp32 and rp2,
including support for numeric pins, rp2 alternate functions, and rp2
extended pins.
This also updates the rp2 port to use the same structure for pins.h and
pins.csv as for esp32, and moves the pin definitions directly into the
table (rather than having a table of pointers), which is a small code size
improvement.
Support for "hidden" pins in pins.csv is added (matching the stm32
implementation).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
All ports now use `--board-csv`, `--prefix`, `--output-souce`,
`--output-header` and no longer write to stdout. This matches the esp32
implementation.
Ports that have an AF input use `--af-csv` (to match `--board-csv`).
Any additional output files are now prefixed with `output-` (e.g.
`--output-af-const`).
Default arguments are removed (all makefiles should always specify all
arguments, using default values is likely an error).
Replaced the `af-defs-cmp-strings` and `hdr-obj-decls` args for stm32 with
just `mboot-mode`. Previously they were set on the regular build, now the
logic is reversed so mboot sets it.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Commit c4e63ace66 enabled the SPI Ethernet
driver and that cost about 13k of firwmare size, pushing the firmware over
the limit of the D2WD and OTA board variants available size.
To fix, disable SPI Ethernet on the D2WD variant, and build the OTA variant
with size optimisation rather than performance optimisation.
Signed-off-by: Damien George <damien@micropython.org>
SPI support was not enabled, and was not adapted for esp-idf v5.x. This
change enables SPI ethernet for all boards and adapts the code for esp-idf
v5.x. The change follows the sample implementation of @hemakumarm72, but
adds the changes for the other adapters as well. Further, it simplifies
the code by removing actions from netwwork_lan.c which are done in the
esp-idf drivers later, like setting the default values for .command_bits
and .address_bits, and registering the SPI interface.
Tested with a Wiznet W5500 breakout.
Signed-off-by: robert-hh <robert@hammelrath.com>
The machine_i2c_type, machine_spi_type and machine_timer_type symbols are
already declared in extmod/modmachine.h and should not be declared anywhere
else.
Also move declarations of machine_pin_type and machine_rtc_type to the
common header in extmod.
Signed-off-by: Damien George <damien@micropython.org>
Also remove corresponding commented line from esp8266/boards/manifest.py.
It doesn't have enough flash to have this frozen by default.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
The IDF-provided version of TinyUSB defaults to Espressif's standard
VID:PID unless specific sdkconfig options are present. The numbers
already defined for the CUSTOM_* config options were ignored otherwise.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Add "CONFIG_BOOTLOADER_APP_ROLLBACK_ENABLE=y" to
ports/esp32/boards/sdkconfig.base so that all micropython esp32 images
support OTA rollback in the bootloader. These images can then be converted
to OTA-capable images as required by user tools.
Also remove CONFIG_BOOTLOADER_APP_ROLLBACK_ENABLE=y from board-specific
sdkconfig files as this is now the default.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
Applies to newly-added ARDUINO_PORTENTA_C33 and UM_NANOS3.
Makes the list match the standard features defined in
24a6e951ec.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
sdkconfig.base: Add CONFIG_BOOTLOADER_SKIP_VALIDATE_IN_DEEP_SLEEP=y.
This reduces time to boot from deepsleep by at least 200ms and can
provide significant power savings for deepsleep-based battery
applications.
docs/library/esp32.rst: Add note cautioning not to enter deepsleep after
changing the boot partition, without first performing a hard reset.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
This should have been added in 4815af75bc
when the variants were combined. The original non-USB variant got this
implicitly, and therefore was not in mpconfigvariant.h
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Board names need to be unique across ports, and GENERIC clashes with
the ESP8266 (which will be renamed to ESP8266_GENERIC).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This was used to override the firmware filename generated by the build
server (to match the historical name before board definitions existed).
Now we're making everything use the board definition name (i.e. the
directory name).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is to support a future change to add the variant name to the build
directory and therefore should be the same style as the board name.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
To be consistent with the other partitions files (which have the "-
{2,8,16,32}MiB" suffix). Also renames partitions-ota.csv.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Unsure of the history of the ESP32_S2_WROVER board (and why it wasn't
named GENERIC_S2_...) but now it's a variant of the generic S2 board.
Also removes the non-existent CONFIG_USB_AND_UART from all S2 boards.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
As the IDF no longer supports earlier revisions of the C3 by default, we
now just explicitly support rev 3+ and enable USB (which wasn't supported
in earlier revisions).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Also shrinks the "prefer internal" threshold to 8KB, any allocation larger
than this will try PSRAM first.
Change the mbedTLS config to use regular malloc() as well, instead of
internal only. The default is set to internal-only due to to potential
physical security issue of readout via PSRAM on the original ESP32.
However, as MicroPython runs from plaintext flash and all other context is
in the MP heap of PSRAM then it's hard to see how worsens physical security
for MP.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This commit:
- Finds a common set of board feature tags and maps existing features to
that reduced set.
- Removes some less-useful board feature tags.
- Ensures all MCUs are specified correctly.
- Ensures all boards have a vendor (and fixes some vendor names).
This is to make the downloads page show a less intimidating set of filters.
Work done in conjunction with Matt Trentini <matt.trentini@gmail.com>.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Listing the IDF version number in the board description is not as important
as it once was, when the IDF was still undergoing a lot of changes. Now,
all builds use IDF 5.x and it's possible to query the exact version with
platform.platform().
Signed-off-by: Damien George <damien@micropython.org>
This adds named-pins support to the esp32 port, following other ports.
Since the name of esp32 CPU pins is just GPIOx, where x is an integer, the
Pin.cpu dict is not supported and CPU pins are just retrieved via their
existing integer "name" (the cost of adding Pin.cpu is about 800 bytes,
mostly due to the additional qstrs).
What this commit supports is the Pin.board dict and constructing a pin by
names given by a board. These names are defined in a pins.csv file at the
board level. If no such file exists then Pin.board exists but is empty.
As part of this commit, pin and pin IRQ objects are optimised to reduce
their size in flash (by removing their gpio_num_t entry). The net change
in firmware size for this commit is about -132 bytes.
Signed-off-by: Damien George <damien@micropython.org>
The legacy driver was deprecated in IDF v5, and crashes when the ISR
handler is called. Instead of fixing the legacy code, this commit reworks
the machine.Timer class to use the low-level HAL driver.
Tested on ESP32, ESP32S2, ESP32S3 and ESP32C3. Behaviour is the same as it
was before this commit, except the way the Timer object is printed, it now
gives more useful information (timer id, mode, period in ms).
Fixes issue #11970.
Signed-off-by: Damien George <damien@micropython.org>
Enabling mDNS put this firmware over the limit of the OTA partition size,
so tweak the compiler settings to reduce the firmware size.
Signed-off-by: Damien George <damien@micropython.org>
This commit updates the esp32 port to work exclusively with ESP-IDF v5.
IDF v5 is needed for some of the newer ESP32 SoCs to work, and it also
cleans up a lot of the inconsistencies between existing SoCs (eg S2, S3,
and C3).
Support for IDF v4 is dropped because it's a lot of effort to maintain both
versions at the same time.
The following components have been verified to work on the various SoCs:
ESP32 ESP32-S2 ESP32-S3 ESP32-C3
build pass pass pass pass
SPIRAM pass pass pass N/A
REPL (UART) pass pass pass pass
REPL (USB) N/A pass pass N/A
filesystem pass pass pass pass
GPIO pass pass pass pass
SPI pass pass pass pass
I2C pass pass pass pass
PWM pass pass pass pass
ADC pass pass pass pass
WiFi STA pass pass pass pass
WiFi AP pass pass pass pass
BLE pass N/A pass pass
ETH pass -- -- --
PPP pass pass pass --
sockets pass pass pass pass
SSL pass ENOMEM pass pass
RMT pass pass pass pass
NeoPixel pass pass pass pass
I2S pass pass pass N/A
ESPNow pass pass pass pass
ULP-FSM pass pass pass N/A
SDCard pass N/A N/A pass
WDT pass pass pass pass
Signed-off-by: Damien George <damien@micropython.org>
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The asyncio module now has much better CPython compatibility and
deserves to be just called "asyncio".
This will avoid people having to write `from uasyncio import asyncio`.
Renames all files, and updates port manifests to use the new path. Also
renames the built-in _uasyncio to _asyncio.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This change enables the ULP (FSM) for all ESP32 variants rather than
requiring it to be enabled for each board specifically.
It also ensures the correct header file is included for each variant.
Lastly, it updates the IDF version we're builing against to v4.4.2, as that
version contains important fixes to make the ULP actually work on S2/S3
chips. See: https://github.com/espressif/esp-idf/commit/a0e3d48
Signed-off-by: Wilko Nienhaus <wilko.nienhaus@gmail.com>
ESP-NOW is a proprietary wireless communication protocol which supports
connectionless communication between ESP32 and ESP8266 devices, using
vendor specific WiFi frames. This commit adds support for this protocol
through a new `espnow` module.
This commit builds on original work done by @nickzoic, @shawwwn and with
contributions from @zoland. Features include:
- Use of (extended) ring buffers in py/ringbuf.[ch] for robust IO.
- Signal strength (RSSI) monitoring.
- Core support in `_espnow` C module, extended by `espnow.py` module.
- Asyncio support via `aioespnow.py` module (separate to this commit).
- Docs provided at `docs/library/espnow.rst`.
Methods available in espnow.ESPNow class are:
- active(True/False)
- config(): set rx buffer size, read timeout and tx rate
- recv()/irecv()/recvinto() to read incoming messages from peers
- send() to send messages to peer devices
- any() to test if a message is ready to read
- irq() to set callback for received messages
- stats() returns transfer stats:
(tx_pkts, tx_pkt_responses, tx_failures, rx_pkts, lost_rx_pkts)
- add_peer(mac, ...) registers a peer before sending messages
- get_peer(mac) returns peer info: (mac, lmk, channel, ifidx, encrypt)
- mod_peer(mac, ...) changes peer info parameters
- get_peers() returns all peer info tuples
- peers_table supports RSSI signal monitoring for received messages:
{peer1: [rssi, time_ms], peer2: [rssi, time_ms], ...}
ESP8266 is a pared down version of the ESP32 ESPNow support due to code
size restrictions and differences in the low-level API. See docs for
details.
Also included is a test suite in tests/multi_espnow. This tests basic
espnow data transfer, multiple transfers, various message sizes, encrypted
messages (pmk and lmk), and asyncio support.
Initial work is from https://github.com/micropython/micropython/pull/4115.
Initial import of code is from:
https://github.com/nickzoic/micropython/tree/espnow-4115.
Rather than duplicating the implementation of `network`, this allows ESP32
to use the shared one in extmod. In particular this gains access to
network.hostname and network.country.
Set default hostnames for various ESP32 boards.
Other than adding these two methods and the change to the default hostname,
there is no other user-visible change.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This will ensure that any board with networking support gets:
- webrepl
- mip
- urequests
- ntptime
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The major setting is about the PHY interface configuration. The
configuration matches the Olimex ESP32 Gateway as well.
Tested with esp-idf v4.2.4 and Olimex ESP32 POE boards.
Jim Mussared
Damien George
robert-hh
Daniël van de Giessen
Seon Rozenblum
Glenn Moloney
Luca Burelli
Sebastian Romero
Angus Gratton
iabdalkader
Wilko Nienhaus
Clayton Cronk
Red_M