led_init() was not called, and therefore the machine.LED class seemed not
to work. led_init() now uses mp_hal_pin_output() to configure the pin.
Signed-off-by: robert-hh <robert@hammelrath.com>
This commit adds the necessary configuration and hooks to get the CYW43
driver working with the mimxrt port.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
The call to machine_uart_deinit_all() is needed to avoid a crash after soft
reset, if a UART had been used and data arrives before it is instantiated
again.
Signed-off-by: robert-hh <robert@hammelrath.com>
Updates all `help()` output to use the phrase:
`For online docs please visit http://docs.micropython.org/`
Some ports previously used different wording, some pointed to the wrong
link. Also make all ports use `help.c` for consistency.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Helps prevent the filesystem from getting formatted by mistake, among other
things. For example, on a Pico board, entering Ctrl+D and Ctrl+C fast many
times will eventually wipe the filesystem (without warning or notice).
Further rationale: Ctrl+C is used a lot by automation scripts (eg mpremote)
and UI's (eg Mu, Thonny) to get the board into a known state. If the board
is not responding for a short time then it's not possible to know if it's
just a slow start up (eg in _boot.py), or an infinite loop in the main
application. The former should not be interrupted, but the latter should.
The only way to distinguish these two cases would be to wait "long enough",
and if there's nothing on the serial after "long enough" then assume it's
running the application and Ctrl+C should break out of it. But defining
"long enough" is impossible for all the different boards and their possible
behaviour. The solution in this commit is to make it so that frozen
start-up code cannot be interrupted by Ctrl+C. That code then effectively
acts like normal C start-up code, which also cannot be interrupted.
Note: on the stm32 port this was never seen as an issue because all
start-up code is in C. But now other ports start to put more things in
_boot.py and so this problem crops up.
Signed-off-by: David Grayson <davidegrayson@gmail.com>
The RT1176 has two cores, but the actual firmware supports only the CM7.
There are currently no good plans on how to use the CM4.
The actual MIMXRT1170_EVK board is on par with the existing MIMXRT boards,
with the following extensions:
- Use 64 MB RAM for the heap.
- Support both LAN interfaces as LAN(0) and LAN(1), with LAN(1)
being the 1GB interface.
The dual LAN port interface can eventually be adapted as well for the
RT1062 MCU.
This work was done in collaboration with @alphaFred.
This commit adds support for machine.I2S on the mimxrt port. The I2S API
is consistent with the existing stm32, esp32, and rp2 implementations.
I2S features:
- controller transmit and controller receive
- 16-bit and 32-bit sample sizes
- mono and stereo formats
- sampling frequencies from 8kHz to 48kHz
- 3 modes of operation:
- blocking
- non-blocking with callback
- uasyncio
- configurable internal buffer
- optional MCK
Tested with the following development boards:
- MIMXRT1010_EVK, MIMXRT1015_EVK, MIMXRT1020_EVK, MIMXRT1050_EVK
- Teensy 4.0, Teensy 4.1
- Olimex RT1010
- Seeed ARCH MIX
Tested with the following I2S hardware peripherals:
- UDA1334
- GY-SPH0645LM4H
- WM8960 codec on board the MIMXRT boards and separate breakout board
- INMP441
- PCM5102
- SGTL5000 on the Teensy audio shield
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
If MICROPY_PY_SYS_PATH_ARGV_DEFAULTS is enabled (which it is by default)
then sys.path and sys.argv will be initialised and populated with default
values. This keeps all bare-metal ports aligned.
Signed-off-by: Damien George <damien@micropython.org>
Frozen modules will be searched preferentially, but gives the user the
ability to override this behavior.
This matches the previous behavior where "" was implicitly the frozen
search path, but the frozen list was checked before the filesystem.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Frequency range 15Hz/18Hz to > 1 MHz, with decreasing resolution of the
duty cycle. The basic API is supported as documentated, except that
keyword parameters are accepted for both the instatiaton and the
PWM.init() call.
Extensions: support PWM for channel pairs. Channel pairs are declared by
supplying 2-element tuples for the pins. The two channels of a pair must
be the A/B channel of a FLEXPWM module. These form than a complementary
pair.
Additional supported keyword arguments:
- center=value Defines the center position of a pulse within the pulse
cycle. The align keyword is actually shortcut for center.
- sync=True|False: If set to True, the channels will be synchronized to a
submodule 0 channel, which has already to be enabled.
- align=PWM.MIDDLE | PMW.BEGIN | PWM.END. It defines, whether synchronized
channels are Center-Aligned or Edge-aligned. The channels must be either
complementary a channel pair or a group of synchronized channels. It may
as well be applied to a single channel, but withiout any benefit.
- invert= 0..3. Controls ouput inversion of the pins. Bit 0 controls the
first pin, bit 1 the second.
- deadtime=time_ns time of complementary channels for delaying the rising
slope.
- xor=0|1|2 xor causes the output of channel A and B to be xored. If
applied to a X channel, it shows the value oif A ^ B. If applied to an A
or B channel, both channel show the xored signal for xor=1. For xor=2,
the xored signal is split between channels A and B. See also the
Reference Manual, chapter about double pulses. The behavior of xor=2 can
also be achieved using the center method for locating a pulse within a
clock period.
The output is enabled for board pins only.
CPU pins may still be used for FLEXPWM, e.g. as sync source, but the signal
will not be routed to the output. That applies only to FLEXPWM pins. The
use of QTMR pins which are not board pins will be rejected.
As part of this commit, the _WFE() statement is removed from
ticks_delay_us64() to prevent PWM glitching during calls to sleep().
This commit implements 10/100 Mbit Ethernet support in the mimxrt port.
The following boards are configured without ETH network:
- MIMXRT1010_EVK
- Teensy 4.0
The following boards are configured with ETH network:
- MIMXRT1020_EVK
- MIMXRT1050_EVK
- MIMXRT1060_EVK
- MIMXRT1064_EVK
- Teensy 4.1
Ethernet support tested with TEENSY 4.1, MIMRTX1020_EVK and MIMXRT1050_EVK.
Build tested with Teensy 4.0 and MIMXRT1010_EVK to be still working.
Compiles and builds properly for MIMXRT1060_EVK and MIMXRT1064_EVK, but not
tested lacking suitable boards.
Tested functions are:
- ping works bothway
- simple UDP transfer works bothway
- ntptime works
- the ftp server works
- secure socker works
- telnet and webrepl works
The MAC address is 0x02 plus 5 bytes from the manifacturing info field,
which can be considered as unique per device.
Some boards do not wire the RESET and INT pin of the PHY transceiver. For
operation, these are not required. If they are defined, they will be used.
This commit adds full support for a filesystem on all boards, with a block
device object mimxrt.Flash() and uos.VfsLfs2 enabled.
Main changes are:
- Refactoring of linker scripts to accomodate reserved area for VFS. VFS
will take up most of the available flash. 1M is reserved for code. 9K is
reserved for flash configuration, interrupts, etc.
- Addition of _boot.py with filesystem init code, called from main.c.
- Definition of the mimxrt module with a Flash class in modmimxrt.[ch].
- Implementation of a flash driver class in mimxrt_flash.c. All flashing
related functions are stored in ITCM RAM.
- Addition of the uos module with filesystem functions.
- Implementation of uos.urandom() for the sake of completeness of the uos
module.
It uses sample code from CircuitPython supplied under MIT license, which
uses the NXP SDK example code.
Done in collaboration with Philipp Ebensberger aka @alphaFred who
contributed the essential part to enable writing to flash while code is
executing, among other things.
SysTick cannot wake the CPU from WFI/WFE so a hardware timer is needed to
keep track of ticks/delay (similar to the nrf port).
Fixes issue #7234.
Signed-off-by: Damien George <damien@micropython.org>
This commit implements an LED class with rudimentary parts of a pin C API
to support it. The LED class does not yet support setting an intensity.
This LED class is put in the machine module for the time being, until a
better place is found.
One LED is supported on TEENSY40 and MIMXRT1010_EVK boards.
No functionality change is intended with this commit, it just consolidates
the separate implementations of GC helper code to the lib/utils/ directory
as a general set of helper functions useful for any port. This reduces
duplication of code, and makes it easier for future ports or embedders to
get the GC implementation correct.
Ports should now link against gchelper_native.c and either gchelper_m0.s or
gchelper_m3.s (currently only Cortex-M is supported but other architectures
can follow), or use the fallback gchelper_generic.c which will work on
x86/x64/ARM.
The gc_helper_get_sp function from gchelper_m3.s is not really GC related
and was only used by cc3200, so it has been moved to that port and renamed
to cortex_m3_get_sp.
This is an extremely minimal port to the NXP i.MX RT, in the style of the
SAMD port It's largely based on the TinyUSB mimxrt implementation, using
the NXP SDK. It currently supports the Teensy 4.0 board with a REPL over
the USB-VCP interface.
This commit also adds the NXP SDK submodule (also from TinyUSB) to
lib/nxp_driver.
Note: if you already have the tinyusb submodule initialized recursively you
will need to run the following as the tinyusb sub-submodules have been
rearranged (upstream):
git submodule deinit lib/tinyusb
rm -rf .git/modules/lib/tinyusb
git submodule update --init lib/tinyusb
Kwabena W. Agyeman
robert-hh
iabdalkader
Jim Mussared
David Grayson
MikeTeachman
Damien George
Philipp Ebensberger