Prior to this commit, only sector 0 was erase/write protected, which may
not be enough to protect all of mboot (especially if mboot lives at a
higher address than the start of flash).
This commit makes sure all internal flash sectors that mboot lives in are
protected from erasing and writing. The linker script must define
_mboot_writable_flash_start for this to work.
Signed-off-by: Damien George <damien@micropython.org>
For STM32L4, hardware I2C can be implemented by using TIMINGR.
This commit enables:
- Use of hardware I2C in machine.I2C.
- Specifying a frequency greater than or equal to 400KHz with pyb.I2C.
For STM32L4 series, the internal sensors are connected to:
- ADC1_IN0: Internal voltage reference
- ADC1_IN17: Temperature sensor
- ADC1_IN18: VBAT battery voltage monitoring
but ADC_CHANNEL_VREFINT, ADC_CHANNEL_VBAT, ADC_CHANNEL_TEMPSENSOR are not
defined as 0, 17, 18.
This commit converts channel 0, 17, 18 to ADC_CHANNEL_x in
adc_get_internal_channel().
Prior to this commit, the actual I2C frequency can be faster than specified
one and it may exceed the I2C's specification for Fast Mode. The frequency
of SCL should be less than or equal to 400KHz in Fast Mode.
This commit fixes this issue for F4 MCUs by rounding up the division in the
frequency calculation.
Excuting the code:
i2c = I2C(1, I2C.CONTROLLER, dma=True)
tmp = i2c.recv(1, i2c_addr)
recv_data = bytearray(56)
i2c.recv(recv_data, i2c_addr)
The second i2c.recv() fails with OSError: [Errno 110] ETIMEDOUT. When
receiving greater than or equal to 2 bytes at first i2c.recv(), the second
i2c.recv() succeeds. This issue does not occur without DMA.
Details of change: when executing I2C with DMA:
- Bit 11 of I2Cx_CR2 (DMA Request Enable) should be 1 to indicate that DMA
transfer is enabled. This bit is set after I2C event interrupt is
enabled in HAL_I2C_Master_Transmit_DMA()/HAL_I2C_Master_Receive_DMA(), so
DMA Request Enable bit might be 0 in IRQHandler.
- In case of data receive:
- When only 1 byte receiption, clear I2Cx_CR1's bit 10 (ACK).
- When only 2 byte receiption, clear I2Cx_CR1's bit 10 (ACK) and set
bit 11 (POS).
- When greater than or equal to 2 byte receiption, bit 12 of I2Cx_CR2
(DMA Last Transfer) should set to generate NACK when DMA transfer
completed.
Otherwise, the I2C bus may be busy after received data from peripheral.
A board can now name the CDC ports, eg:
#define MICROPY_HW_USB_CDC_NUM (3)
#define MICROPY_HW_USB_INTERFACE_CDC0_STRING "REPL"
#define MICROPY_HW_USB_INTERFACE_CDC1_STRING "GDB Server"
#define MICROPY_HW_USB_INTERFACE_CDC2_STRING "UART Port"
Signed-off-by: Damien George <damien@micropython.org>
Seems unused outside of spi.c, spi_obj[] array is the expected way to
iterate these.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This is necessary to access sites that only support these protocols.
The rp2 port already has ECDH enabled, so this just adds ECDSA there. The
other ports now gain both ECDH and ECDSA. The code size increase is:
- rp2 (PICO_W): +2916 bytes flash, +24 bytes BSS
- stm32 (PYBD_SF6): +20480 bytes flash, +32 bytes data, +48 bytes BSS
- mimxrt (TEENSY41): +20708 bytes flash, +32 bytes data, +48 bytes BSS
- unix (standard x86-64): +39344 executable, +1744 bytes data, +96 BSS
This is obviously a large increase in code size. But there doesn't seem to
be any other option because without elliptic curve cryptography devices are
partially cut off from the internet. For use cases that require small
firmware size, they'll need to build custom firmware with a custom mbedtls
config.
Signed-off-by: Damien George <damien@micropython.org>
The following multi-tests pass (eg with PYBD_SF6+LEGO_HUB_NO6):
ble_gap_advertise.py
ble_gap_connect.py
ble_gap_device_name.py
ble_gattc_discover_services.py
ble_gatt_data_transfer.py
perf_gatt_char_write.py
perf_gatt_notify.py
stress_log_filesystem.py
These are the same tests that passed prior to this BTstack update.
Also tested on the unix port using H4 transport.
Signed-off-by: Damien George <damien@micropython.org>
This makes it so that all a port needs to do is set the relevant variables
and "include extmod.mk" and doesn't need to worry about adding anything to
OBJ, CFLAGS, SRC_QSTR, etc.
Make all extmod variables (src, flags, etc) private to extmod.mk.
Also move common/shared, extmod-related fragments (e.g. wiznet, cyw43,
bluetooth) into extmod.mk.
Now that SRC_MOD, CFLAGS_MOD, CXXFLAGS_MOD are unused by both extmod.mk
(and user-C-modules in a previous commit), remove all uses of them from
port makefiles.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This applies to nimble, btstack, axtls, mbedtls, lwip.
Rather than having the ports individually manage GIT_SUBMODULES for these
components, make extmod.mk append them when the relevant feature is
enabled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Removes the need for the port to add anything to OBJS or SRC_QSTR.
Also makes it possible for user-C-modules to differentiate between code
that should be processed for QSTR vs other files (e.g. helpers and
libraries).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Instead of being an explicit field, it's now a slot like all the other
methods.
This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The goal here is to remove a slot (making way to turn make_new into a slot)
as well as reduce code size by the ~40 references to mp_identity_getiter
and mp_stream_unbuffered_iter.
This introduces two new type flags:
- MP_TYPE_FLAG_ITER_IS_ITERNEXT: This means that the "iter" slot in the
type is "iternext", and should use the identity getiter.
- MP_TYPE_FLAG_ITER_IS_CUSTOM: This means that the "iter" slot is a pointer
to a mp_getiter_iternext_custom_t instance, which then defines both
getiter and iternext.
And a third flag that is the OR of both, MP_TYPE_FLAG_ITER_IS_STREAM: This
means that the type should use the identity getiter, and
mp_stream_unbuffered_iter as iternext.
Finally, MP_TYPE_FLAG_ITER_IS_GETITER is defined as a no-op flag to give
the default case where "iter" is "getiter".
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Since L4 HAL version 1.17.0, HAL_TIM_IC_Start_IT() checks whether specified
channel of timer is busy or not, which is the case if this function is
called more than once without first calling HAL_TIM_IC_Stop_IT(). The fix
in this commit is to call the stop function before calling start. The PWM
and OC modes have the same issue with the same fix.
Fixes issue #8732.
Prior to this commit, excuting this code:
i2c = I2C(1, I2C.CONTROLLER, dma=True)
i2c.send(data, addr=i2c_addr)
the call to i2c.send() does not return and the board needs a reset. This
code works when dma=False.
According to the specification, I2Cx_EV_IRQHandler should:
- Write DR to address when Start condition generated.
- Clear ADDR by reading SR2 after reading SR2 when address sent.
These processes are included in HAL_I2C_EV_IRQHandler(), however the
firmware size increses about 2KB if HAL_I2C_EV_IRQHandler is called. This
commit adds above processes to i2c_ev_irq_handler, and increases firmware
by less than 100 bytes.
Fixes issue #2643.
pyb.ADC(channel) checks whether specified channel is valid or have ADC
capability but pyb.ADCAll().read_channel() does not.
This change adds checking whether specified channel is valid and throw
ValueError if channel is invalid. This is same as pyb.ADC().
Although this driver and associated hardware can be used on any board, it
makes to only freeze it for PYB and PYBD boards. It can be easily copied
to any board if needed.
Fixes issue #8056.
Signed-off-by: Damien George <damien@micropython.org>
Changes in this commit:
- Manifest include's now use the directory path where possible (no longer
necessary to include the manifest.py file explicitly).
- Add manifest.py for all drivers and components that are referenced by
port/board manifests.
- Replace all uses of freeze() with package()/module(), except for port and
board modules.
- Use opt=3 everywhere, for consistency and to reduce code size.
- Use require() instead of include() for all micropython-lib references.
- Remove support for optional board-level manifest.py in mimxrt port, to
make it behave the same as other ports (the board must set
FROZEN_MANIFEST to a custom manifest.py, which can optionally include the
default, port-level manifest).
- Also reinstates modules that were accidentally removed from the esp8266
512k build in fbe9417b90.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
Since uart.write() of the STM32 port waits until all bytes have
been sent, uart.flush() and uart.txdone() are implemented as empty
functions to provide API consistency.
uart.flush()
flush() will always return immediately.
ret = uart.txdone()
uart.txdone() will always return True.
Previously the desired output type was specified. Now make the type part
of the function name. Because this function is used in a few places this
saves code size due to smaller call-site.
This makes `mp_obj_new_str_type_from_vstr` a private function of objstr.c
(which is almost the only place where the output type isn't a compile-time
constant).
This saves ~140 bytes on PYBV11.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
It has been about 8 years since support for this chip was added. Reasons
to remove it are:
- It is no longer easy to obtain this part.
- There are now many other options for WiFi.
- It's not a good use of developer time to maintain it.
Signed-off-by: Damien George <damien@micropython.org>
Not safe to use mp_hal_delay_ms before boot if threading is enabled,
because threading will not have been initialised, and
MICROPY_EVENT_POLL_HOOK assumes threading is initialised.
HAL_Delay doesn't call MICROPY_EVENT_POLL_HOOK, but is still
power-efficient like mp_hal_delay_ms (unlike mp_hal_delay_us).
Fixes#7816.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Rather than having the autobuild know about the particular variants, have
the mpconfigboard.mk describe them and make autobuild discover them
automatically.
Adds a "query-variants" target to stm32/Makefile to allow the set of
possible variants to be queried.
Removes pybv3 from the autobuild as this isn't use by the downloads page.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
If mboot is built with support for packing (signing/encryption) it needs up
to 32KiB. So for simplicity increase the mboot region to 32KiB
unconditionally for WB55 boards (custom WB55 board configurations can still
provide their own linker scripts to override this).
Damien George
yn386
Jim Mussared
Koen De Vleeschauwer
iabdalkader
Angus Gratton
robert-hh
Jatty_
Andrew Leech