This patch adds quickref documentation for the change in commit
afd0701bf7. This commit added the ability to
disable the REPL and hence use UART0 for serial communication on the
esp8266, but was not previously documented anywhere.
The text is largely taken from the commit message, with generic information
on using the UART duplicated from the Wipy quickref document.
This enables warnings as errors and fixes all current errors, namely:
- reference to terms in the glossary must now be explicit (:term:)
- method overloads must not be declared as a separate method or must
use :noindex:
- 2 cases where `` should have been used instead of `
This commit makes sure that all discovery complete and read/write status
events set the status to zero on success.
The status value will be implementation-dependent on non-success cases.
This commit allows the user to set/get the GAP device name used by service
0x1800, characteristic 0x2a00. The usage is:
BLE.config(gap_name="myname")
print(BLE.config("gap_name"))
As part of this change the compile-time setting
MICROPY_PY_BLUETOOTH_DEFAULT_NAME is renamed to
MICROPY_PY_BLUETOOTH_DEFAULT_GAP_NAME to emphasise its link to GAP and this
new "gap_name" config value. And the default value of this for the NimBLE
bindings is changed from "PYBD" to "MPY NIMBLE" to be more generic.
This commit adds several small items to improve the support for OTA
updates on an esp32:
- a partition table for 4MB flash modules that has two OTA partitions ready
to go to do updates
- a GENERIC_OTA board that uses that partition table and that enables
automatic roll-back in the bootloader
- a new esp32.Partition.mark_app_valid_cancel_rollback() class-method to
signal that the boot is successful and should not be rolled back at the
next reset
- an automated test for doing an OTA update
- documentation updates
This commit adds full support to the unix port for Bluetooth using the
common extmod/modbluetooth Python bindings. This uses the libusb HCI
transport, which supports many common USB BT adaptors.
This commit adds an idf_heap_info(capabilities) method to the esp32 module
which returns info about the ESP-IDF heaps. It's useful to get a bit of a
picture of what's going on when code fails because ESP-IDF can't allocate
memory anymore. Includes documentation and a test.
This commit adds Loop.new_event_loop() which is used to reset the singleton
event loop. This functionality is put here instead of in Loop.close() to
make it possible to write code that is compatible with CPython.
This commit changes the esp8266 boards to use littlefs v2 as the
filesystem, rather than FAT. Since the esp8266 doesn't expose the
filesystem to the PC over USB there's no strong reason to keep it as FAT.
Littlefs is smaller in code size, is more efficient in use of flash to
store data, is resilient over power failure, and using it saves about 4k of
heap RAM, which can now be used for other things.
This is a backwards incompatible change because all existing esp8266 boards
will need to update their filesystem after installing new firmware (eg
backup old files, install firmware, restore files to new filesystem).
As part of this commit the memory layout of the default board (GENERIC) has
changed. It now allocates all 1M of memory-mapped flash to the firmware,
so the filesystem area starts at the 2M point. This is done to allow more
frozen bytecode to be stored in the 1M of memory-mapped flash. This
requires an esp8266 module with 2M or more of flash to work, so a new board
called GENERIC_1M is added which has the old memory-mapping (but still
changed to use littlefs for the filesystem).
In summary there are now 3 esp8266 board definitions:
- GENERIC_512K: for 512k modules, doesn't have a filesystem.
- GENERIC_1M: for 1M modules, 572k for firmware+frozen code, 396k for
filesystem (littlefs).
- GENERIC: for 2M (or greater) modules, 968k for firmware+frozen code,
1M+ for filesystem (littlefs), FAT driver also included in firmware for
use on, eg, external SD cards.
This commit adds micropython.heap_locked() which returns the current
lock-depth of the heap, and can be used by Python code to check if the heap
is locked or not. This new function is configured via
MICROPY_PY_MICROPYTHON_HEAP_LOCKED and is disabled by default.
This commit also changes the return value of micropython.heap_unlock() so
it returns the current lock-depth as well.
This commit changes the BLE _IRQ_SCAN_RESULT data from:
addr_type, addr, connectable, rssi, adv_data
to:
addr_type, addr, adv_type, rssi, adv_data
This allows _IRQ_SCAN_RESULT to handle all scan result types (not just
connectable and non-connectable passive scans), and to distinguish between
them using adv_type which is an integer taking values 0x00-0x04 per the BT
specification.
This is a breaking change to the API, albeit a very minor one: the existing
connectable value was a boolean and True now becomes 0x00, False becomes
0x02.
Documentation is updated and a test added.
Fixes#5738.
The default value for MICROPYPATH used in unix/main.c is
"~/.micropython/lib:/usr/lib/micropython" which has 2 problems when used in
the Windows port:
- it has a ':' as path separator but the port uses ';' so the entire string
is effectively discarded since it gets interpreted as a single path which
doesn't exist
- /usr/lib/micropython is not a valid path in a standard Windows
environment
Override the value with a suitable default.
This fix can be demonstrated by the following:
b = bytearray(32)
f = framebuf.FrameBuffer(b, 32, 8, framebuf.MONO_HLSB)
f.pixel(0, 0, 1)
print('MONO_HLSB', hex(b[0]))
b = bytearray(32)
f = framebuf.FrameBuffer(b, 32, 8, framebuf.MONO_HMSB)
f.pixel(0, 0, 1)
print('MONO_HMSB', hex(b[0]))
Outcome:
MONO_HLSB 0x80
MONO_HMSB 0x1
This adds a -h option to print the usage help text and adds a new, shorter
error message that is printed when invalid arguments are given. This
behaviour follows CPython (and other tools) more closely.
Show how to send an HTTP response code and content-type. Without the
response code Safari/iOS will fail. Without the content-type Lynx/Links
will fail.
This adds a short paragraph on how to hook readthedocs.org up. The main
goal is to make people aware of the option, to help with contributing to
the documentation.
Nick Crabtree
Damien George
David Lechner
Jim Mussared
Andrew Leech
cccc
Thorsten von Eicken
Thorsten von Eicken
Thomas Friebel
Peter Hinch
Lars Kellogg-Stedman
Andrew Leech
stijn
Jesse Andrews
adzierzanowski
Peter Hinch
Jason Neal
Matt Trentini
ketograph