This applies to all machine modules which have pins as arguments. Since
machine_pin_get_id() calls pin_find(), these pin arguments may be at the
moment either integer objects or Pin objects. That allows for instance to
write
uart = UART(1, tx=Pin(4), rx=Pin(5))
instead of
uart = UART(1, tx=4, rx=5)
which is consistent with other ports. Since this handling is done at a
single place in the code, extending that scheme to accept strings for named
pins is easy.
Signed-off-by: robert-hh <robert@hammelrath.com>
This commit updates the esp32 port to work exclusively with ESP-IDF v5.
IDF v5 is needed for some of the newer ESP32 SoCs to work, and it also
cleans up a lot of the inconsistencies between existing SoCs (eg S2, S3,
and C3).
Support for IDF v4 is dropped because it's a lot of effort to maintain both
versions at the same time.
The following components have been verified to work on the various SoCs:
ESP32 ESP32-S2 ESP32-S3 ESP32-C3
build pass pass pass pass
SPIRAM pass pass pass N/A
REPL (UART) pass pass pass pass
REPL (USB) N/A pass pass N/A
filesystem pass pass pass pass
GPIO pass pass pass pass
SPI pass pass pass pass
I2C pass pass pass pass
PWM pass pass pass pass
ADC pass pass pass pass
WiFi STA pass pass pass pass
WiFi AP pass pass pass pass
BLE pass N/A pass pass
ETH pass -- -- --
PPP pass pass pass --
sockets pass pass pass pass
SSL pass ENOMEM pass pass
RMT pass pass pass pass
NeoPixel pass pass pass pass
I2S pass pass pass N/A
ESPNow pass pass pass pass
ULP-FSM pass pass pass N/A
SDCard pass N/A N/A pass
WDT pass pass pass pass
Signed-off-by: Damien George <damien@micropython.org>
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Change UART clock source on S3/C3 so the UART can operate when CPU
frequency is below 80MHz. This allows the UART to remain operational when
using Dynamic Frequency Scaling (DFS).
Signed-off-by: Patrick Joy <patrick@joytech.com.au>
Instead of being an explicit field, it's now a slot like all the other
methods.
This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The goal here is to remove a slot (making way to turn make_new into a slot)
as well as reduce code size by the ~40 references to mp_identity_getiter
and mp_stream_unbuffered_iter.
This introduces two new type flags:
- MP_TYPE_FLAG_ITER_IS_ITERNEXT: This means that the "iter" slot in the
type is "iternext", and should use the identity getiter.
- MP_TYPE_FLAG_ITER_IS_CUSTOM: This means that the "iter" slot is a pointer
to a mp_getiter_iternext_custom_t instance, which then defines both
getiter and iternext.
And a third flag that is the OR of both, MP_TYPE_FLAG_ITER_IS_STREAM: This
means that the type should use the identity getiter, and
mp_stream_unbuffered_iter as iternext.
Finally, MP_TYPE_FLAG_ITER_IS_GETITER is defined as a no-op flag to give
the default case where "iter" is "getiter".
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
uart.flush()
flush() will wait until all characters have been sent.To
avoid a permanent lock, a timeout applies depending on the
size of txbuf and the baud rate.
ret = uart.txdone()
ret is True if no transfer is in progress.
ret is False otherwise.
It used to be 10 bit times, which is too short. The break state must be
longer than a regular character time, at least 13 bit times. This is now
implemented by reducing the baudrate while sending the "0". The break time
will now vary with data length and parity setting, but will at least be 15
bit times.
Tested with a GENERIC_SPIRAM, GENERIC_C3 and UM_TINYS2 board.
Using it for the rx-timeout. The value is given as ms, which is then
converted to character times. A value of less than a character time will
cause the rx call to return immediately after 1 character, which may be
inefficient at high transmission rates.
Addresses #8778.
This replaces occurences of
foo_t *foo = m_new_obj(foo_t);
foo->base.type = &foo_type;
with
foo_t *foo = mp_obj_malloc(foo_t, &foo_type);
Excludes any places where base is a sub-field or when new0/memset is used.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This enables optional support for the hardware UART to use the RTS and/or
CTS pins for flow control.
The new "flow" constructor keyword specifies a bitmask of RTS and/or CTS.
This matches the interface used by machine.UART on stm32 and rp2.
Previously on ESP32 it was possible to specify which pins to use for the
RTS and CTS signals, but hardware flow control was never functional: CTS
was not checked before transmitting bytes, and RTS was always driven high
(signalling no buffer space available). With this patch, CTS and RTS both
operate as expected.
This also includes an update to the machine.UART documentation.
Signed-off-by: Will Sowerbutts <will@sowerbutts.com>
This event queue has UART events posted to it and they need to be drained
for it to operate without error. The queue is not used by the uPy UART
class so it should be removed to prevent the IDF emitting errors.
Fixes#3704.
This commit is a combination of 216 commits from the initial stages of
development of this port, up to and including the point where the code was
moved to the ports/esp32 directory. These commits were mostly concerned
with setting up the build system and getting a reliable port working with
basic features. The following is a digest of the original commits in their
original order (most recent listed first), grouped where possible per
author. The list is here to give credit for the work and provide some
level of traceability and accountability. For the full history of
development please consult the original repository.
All code is MIT licensed and the relevant copyright holders are listed in
the comment-header of each file.
Damien George <damien.p.george@gmail.com>
esp32: Update to latest ESP IDF.
esp32: Update module symlinks now that code lives under the ports dir.
esp32: Update to compile with new ports/esp32 directory structure.
esp32: Move it to the ports/ directory.
esp32/machine_uart: Don't save baudrate but compute it instead.
esp32/modsocket: Add socket.readinto() method.
esp32/modesp: Add esp.gpio_matrix_in and esp.gpio_matrix_out functions.
esp32/machine_uart: Wait for all data to be tx'd before changing config.
NyxCode <moritz.bischof1@gmail.com>
esp32: Add note to README.md about updating the submodules of ESP IDF.
Anthony Briggs <anthony.briggs@gmail.com>
esp32: Update README.md installation and flashing instructions.
Javier Candeira <javier@candeira.com>
esp32: Raise error when setting input-only pin to output.
With help from Adrian Smith (fon@thefon.net)
Javier Candeira <javier@candeira.com>
esp32: Replace exception raising with corresponding mp_raise_XXX funcs.
Tisham Dhar <whatnickd@gmail.com>
esp32: Add some specific notes about building on Windows using WSL.
Ben Gamari <ben@smart-cactus.org>
esp32: Provide machine.Signal class.
Damien George <damien.p.george@gmail.com>
esp32/modnetwork: Implement AP version of network.isconnected().
Eric Poulsen <eric@zyxod.com>
esp32/README.md: Add note about btree submodule initialization.
Damien George <damien.p.george@gmail.com>
esp32: Make firmware.bin start at 0x1000 to allow flash size autodetect.
esp32: Changes to follow latest version of upstream uPy.
esp32/Makefile: Separate ESP-specific inc dirs to avoid header clashes.
esp32: Enable "btree" database module.
esp32: Update to latest ESP IDF.
Roosted7 <thomasroos@live.nl>
esp32: Update to latest ESP-IDF.
Alex King <alex_w_king@yahoo.com>
esp32/machine_timer: Add support for esp32 hardware timer.
Code lineage:
Timer() is based loosely on the version in esp8266, although the
implementation is differs significantly because of the change in
the underlying platform.
Damien George <damien.p.george@gmail.com>
esp32/machine_uart: Increase UART TX buffer size to 64.
esp32/modules: Update dht symlink.
esp32/mpconfigport.h: Enable utimeq module, needed for uasyncio.
esp32: Changes to follow latest version of upstream uPy.
esp32: Update to latest ESP-IDF.
esp32/machine_uart: Add uart.any() method.
esp32/machine_uart: Uninstall the UART driver before installing it.
Thomas Roos <mail@thomasroos.nl>
esp32: Update to latest ESP-IDF.
Eric Poulsen <eric@zyxod.com>
esp32/modsocket: Make read/write return None when in non-blocking mode.
esp32/modsocket.c: Fix send/sendto/write for non-blocking sockets.
Odd Stråbø <oddstr13@openshell.no>
esp32: Initial working implementation of machine.UART.
Code lineage (as seen by previous commits): I copied the ESP8266 code,
renamed pyb -> machine, and used esp-idf as a reference while implementing
minimal functionality. I provide all of my changes under the MIT license.
Odd Stråbø <oddstr13@openshell.no>
esp32/machine_uart: Rename pyb to machine.
esp32: Copy machine_uart.c from esp8266 port.
Damien George <damien.p.george@gmail.com>
esp32/moduos: Add uos.ilistdir() function.
esp32: Mount filesystem at the root of the VFS, following esp8266.
Andy Valencia <vandyswa@gmail.com>
esp32: Add hardware SHA1/SHA256 support via mbedtls API.
Code lineage: a copy of extmod/moduhashlib with the API invocation details
edited. Total derivative work.
Andy Valencia <vandyswa@gmail.com>
esp32: Add PWM support via machine.PWM class.
Code lineage:
I started by copying the esp8266 machine_pwm.c. I used information from the
ESP32 Technical Reference Manual, the esp-idf documentation, and the SDK's
sample ledc example code (but I did not copy that code, just studied it to
understand the SDK's API for PWM). So aside from the code copied from the
esp8266 PWM support, everything else you see is just new code I wrote.
I wasn't an employee of anybody when I wrote it, and I wrote it with the
understanding and intention that it's simply a derivative work of the
existing micropython code. I freely and willingly contribute it to the
project and intend that it not change the legal status of the micropython
code base in any way, even if it is included in that base in whole or part.
Damien George <damien.p.george@gmail.com>
esp32/modules: Add symlinks for upysh and upip.
Eric Poulsen <eric@zyxod.com>
esp32/modmachine: Add unique_id() function to machine module.
Damien George <damien.p.george@gmail.com>
esp32: Change dac_out_voltage to dac_output_voltage for new IDF API.
esp32: Update esp32.custom_common.ld to align with changes in ESP IDF.
Eric Poulsen <eric@zyxod.com>
esp32: Update to latest ESP IDF.
Damien George <damien.p.george@gmail.com>
esp32/modsocket: When resolving IP addr handle the case of host=''.
esp32: Update to latest ESP IDF.
Eric Poulsen <eric@zyxod.com>
esp32/Makefile: Change default FLASH_MODE to dio for WROOM-32 module.
esp32: Move FAT FS to start at 0x200000 and increase size to 2MiB.
Damien George <damien.p.george@gmail.com>
esp32: Remove enable_irq/disable_irq and use ATOMIC_SECTION instead.
esp32/mpconfigport.h: Provide ATOMIC_SECTION macros.
esp32/main: Restart the MCU if there is a failed NLR jump.
Daniel Campora <daniel@pycom.io>
esp32: Enable threading; be sure to exit GIL when a thread will block.
esp32: Trace the registers when doing a gc collect. Also make it thread ready.
esp32: Add threading implementation, disabled for the time being.
Damien George <damien.p.george@gmail.com>
esp32: Update to latest ESP IDF.
esp32/uart: Use high-level function to install UART0 RX ISR handler.
esp32/Makefile: Make FreeRTOS private include dir really private.
Eric Poulsen <eric@zyxod.com>
esp32: Add support for hardware SPI peripheral (block 1 and 2).
Sergio Conde Gómez <skgsergio@gmail.com>
esp32/modules/inisetup.py: Mount filesystem at /flash like ESP8266
Damien George <damien.p.george@gmail.com>
esp32: Convert to use core-provided KeyboardInterrupt exception.
esp32: Pump the event loop while waiting for rx-chr or delay_ms.
esp32: Implement Pin.irq() using "soft" scheduled interrupts.
esp32: Update to latest ESP IDF version.
Eric Poulsen <eric@zyxod.com>
esp32/README: Add troubleshooting section to the end.
tyggerjai <tyggerjai@gmail.com>
esp32: Add support for WS2812 and APA106 RGB LEDs.
Damien George <damien.p.george@gmail.com>
esp32: Add makeimg.py script to build full firmware; use it in Makefile.
esp32/modsocket: Make socket.read return when socket closes.
esp32/modsocket: Initialise the timeout on an accepted socket.
esp32/mphalport: Provide proper implementations of disable_/enable_irq.
esp32/modmachine: Add disable_irq/enable_irq functions.
Nick Moore <nick@zoic.org>
esp32/modsocket.c: add comment explaining timeout behaviour
esp32/modsocket.c: clean up send methods for retries too
esp32/modsocket.c: sockets always nonblocking, accept timeout in modsocket
esp32: Update to latest ESP IDF version.
esp32/modsocket.c: remove MSG_PEEK workaround on select ioctl.
esp32/modsocket.c: Initialize tcp when modsocket loads.
Damien George <damien.p.george@gmail.com>
esp32/main: Bump heap size from 64k to 96k.
esp32/modutime: Add time.time() function.
esp32/modsocket: Convert lwip errnos to uPy ones.
esp32/modules: Provide symlink to ds18x20 module.
esp32: Add support for onewire protocol via OneWire module.
esp32: Add support for DHT11 and DHT22 sensors.
esp32/mphalport: Improve delay and ticks functions.
esp32: Update to latest ESP IDF.
esp32/modules: Provide symlink to urequests from micropython-lib.
esp32: Populate sys.path.
Nick Moore <nick@zoic.org>
esp32/machine_dac.c: implement DAC pins as well
esp32/machine_adc.c: also machine.ADC
esp32/machine_touchpad.c: add support for touchpad
Damien George <damien.p.george@gmail.com>
esp32/README: Add hint about using GNUmakefile on case-insensitive FS.
esp32/mpconfigport.h: Enable maximum speed software SPI.
esp32: Provide improved version of mp_hal_delay_us_fast.
esp32/mpconfigport.h: Enable MICROPY_PY_BUILTINS_POW3 option.
esp32: Update to latest ESP IDF.
esp32: Convert to use new oofatfs library and generic VFS sub-system.
esp32: Enable help('modules') to list builtin modules.
esp32: Convert to use new builtin help function.
Aaron Kelly <AaronKelly@email.com>
esp32/README: Add comment about ESP-IDF version
Damien George <damien.p.george@gmail.com>
esp32: Consistently use size_t instead of mp_uint_t.
esp32: Change "Micro Python" to "MicroPython" in license comments.
esp32/Makefile: Use -C argument to git instead of cd'ing.
esp32/help: Add section to help about using the network module.
esp32/README: Add section about configuring and using an ESP32 board.
esp32/README: Remove paragraph about buggy toolchain, it's now fixed.
esp32/modnetwork: Change network init logging from info to debug.
esp32/modnetwork: Don't start AP automatically when init'ing wifi.
esp32/modsocket: Implement socket.setsockopt, to support SO_REUSEADDR.
esp32: Update to latest ESP IDF.
esp32/sdkconfig.h: Remove unused CONFIG_ESPTOOLPY_xxx config settings.
esp32/modsocket: Add support for DGRAM and RAW, and sendto/recvfrom.
esp32/modsocket: Fix return value of "port" in socket.accept.
esp32/modsocket: Make socket.recv take exactly 2 args.
esp32: Enable ussl module, using mbedtls component from ESP IDF.
esp32/modsocket: Rename "socket" module to "usocket".
esp32/sdkconfig: Increase max number of open sockets from 4 to 8.
esp32/modsocket: Add error checking for creating and closing sockets.
esp32/modsocket: Use _r (re-entrant) versions of LWIP socket API funcs.
esp32/modsocket: Raise an exception if socket.connect did not succeed.
esp32/modsocket: Make socket.accept return a tuple: (client, addr).
esp32/modsocket: Use m_new_obj_with_finaliser instead of calloc.
esp32/Makefile: Add check for IDF version, and warn if not supported.
esp32/esp32.custom_common.ld: Update to follow changes in IDF.
esp32: Update to latest ESP IDF.
nubcore <x@nubcore.com>
esp32: add #define CONFIG_ESP32_WIFI_RX_BUFFER_NUM 25
Nick Moore <nick@zoic.org>
esp32/modsocket.c: add in sendall and makefile methods #10
esp32/modsocket.c: fixups for #10
esp32/modsocket.c: fix copyright, socket_recv gets param and exception
esp32/modnetwork.c: fix copyright, network.active param to bool
Damien George <damien.p.george@gmail.com>
esp32/modnetwork: Implement wlan.isconnected() method.
esp32/modnetwork: Add initial implementation of wlan.config().
esp32/modnetwork: Simplify event_handler messages.
Nick Moore <nick@zoic.org>
esp32/modsocket.c: support for ioctl, settimeout, setblocking, getaddrinfo
Damien George <damien.p.george@gmail.com>
esp32/README: Add comment about FLASH_MODE being dio.
esp32: Update to latest ESP IDF.
esp32/modnetwork: Remove unnecessary indirection variable for scan list.
esp32/modnetwork: Check that STA is active before trying to scan.
esp32/mphalport: Replace portTICK_RATE_MS with portTICK_PERIOD_MS.
esp32/README: Add comment about using $(HOME) in makefile.
esp32/modnetwork: Use memset instead of bzero, the latter is deprecated.
esp32/modnetwork: Improve error handling when STA is connecting to AP.
esp32/Makefile: Use tab instead of spaces, and use shorter variable.
Nick Moore <nick@zoic.org>
esp32/modsocket.c: AF_*, SOCK_* and IPPROTO_* constants
esp32/modsocket.c: socket.settimeout implementation
Damien George <damien.p.george@gmail.com>
esp32/Makefile: Update to latest ESP IDF.
Nick Moore <nick@zoic.org>
esp32/modsocket.c: use mp streams for sockets
esp32: network.WLAN.ifconfig based on esp8266 version
esp32: Fix up exception handling
esp32: sketchy modsocket ... revisit this once modnetwork is sorted
esp32: First cut at modnetwork, manually rebased from prev. version
Damien George <damien.p.george@gmail.com>
esp32/help: Update help text.
esp32: Add info about Microbric Pty Ltd being the sponsor of this port.
esp32: Add README.md file.
esp32/mpconfigport.h: Add weak links to many of the builtin modules.
esp32: Enable soft implementation of machine.SPI class.
esp32/Makefile: Simplify APP_LD_ARGS by using OBJ variable.
esp32/Makefile: Reorganise Makefile and add some comments.
esp32/Makefile: Clean up CFLAGS for ESP IDF components.
esp32/Makefile: Tidy up names of ESP IDF components, to match dir name.
esp32/Makefile: Define and use ESPCOMP variable.
esp32: Update to latest ESP IDF.
esp32/main: Enable filesystem support.
esp32: Use custom ld script to ensure correct code get placed in iram.
esp32: Update to latest ESP IDF.
esp32/main: Pin the uPy task to core 0.
esp32: Update to use latest ESP IDF.
esp32: Disable boot-up scripts, spi_flash_erase_sector no longer works.
esp32: Add scripts to init and mount filesystem.
esp32: Enable frozen bytecode, with scripts stored in "modules/" dir.
esp32/modesp: Increase flash_user_start position to 1Mbyte.
esp32/Makefile: Add "erase" target for convenient erasure.
esp32/sdkconfig: Reorder config settings to put common things together.
esp32/sdkconfig: Change to use single core only.
esp32: Add esp module.
esp32/uart.c: Make sure uart ISR handler is all in iram.
esp32/main.c: Use ESP_TASK_PRIO_MIN + 1 for mp_task's priority.
esp32/Makefile: Use only bare-minimum flags when compiling .S files.
esp32/Makefile: Rename "firmware" to "application".
esp32: Update ESP IDF version.
esp32/Makefile: Add declarations to build bootloader and partitions.
esp32/Makefile: When deploying, write the application last.
esp32/Makefile: Use $(INC) variable instead of listing include dirs.
esp32/Makefile: Use locally built versions of freertos and newlib libs.
esp32: Add low-level uart handler with ISR and ringbuf for stdin.
esp32: Add machine.idle() function.
esp32: Add machine.I2C class.
esp32: Enable machine.time_pulse_us.
esp32: Add initial implementation of machine.Pin class.
esp32: Prepare main.c for using xTaskCreateStatic.
esp32: Clean up mphalport.h.
esp32: Add initial uos module.
esp32: Clean up mpconfigport.h, enable more features.
esp32: Use new reset function.
esp32: Update to latest ESP IDF.
esp32: Add idf-version target to Makefile, to track IDF commit.
esp32: Initial port to ESP32.
robert-hh
Damien George
patrick
Jim Mussared
Andrew Leech
Will Sowerbutts
Damien George
Jeremy Herbert