If a port defines MICROPY_READER_POSIX or MICROPY_READER_FATFS then
lexer.c now provides an implementation of mp_lexer_new_from_file using
the mp_reader_new_file function.
Implementations of persistent-code reader are provided for POSIX systems
and systems using FatFS. Macros to use these are MICROPY_READER_POSIX and
MICROPY_READER_FATFS respectively. If an alternative implementation is
needed then a port can define the function mp_reader_new_file.
Its addition was due to an early exploration on how to add CPython-like
stream interface. It's clear that it's not needed and just takes up
bytes in all ports.
As required for further elaboration of uasyncio, like supporting baremetal
systems with wraparound timesources. This is not intended to be public
interface, and likely will be further refactored in the future.
Now the function properly uses ring arithmetic to return signed value
in range (inclusive):
[-MICROPY_PY_UTIME_TICKS_PERIOD/2, MICROPY_PY_UTIME_TICKS_PERIOD/2-1].
That means that function can properly process 2 time values away from
each other within MICROPY_PY_UTIME_TICKS_PERIOD/2 ticks, but away in
both directions. For example, if tick value 'a' predates tick value 'b',
ticks_diff(a, b) will return negative value, and positive value otherwise.
But at positive value of MICROPY_PY_UTIME_TICKS_PERIOD/2-1, the result
of the function will wrap around to negative -MICROPY_PY_UTIME_TICKS_PERIOD/2,
in other words, if a follows b in more than MICROPY_PY_UTIME_TICKS_PERIOD/2 - 1
ticks, the function will "consider" a to actually predate b.
Based on the earlier discussed RFC. Practice showed that the most natural
order for arguments corresponds to mathematical subtraction:
ticks_diff(x, y) <=> x - y
Also, practice showed that in real life, it's hard to order events by time
of occurance a priori, events tend to miss deadlines, etc. and the expected
order breaks. And then there's a need to detect such cases. And ticks_diff
can be used exactly for this purpose, if it returns a signed, instead of
unsigned, value. E.g. if x is scheduled time for event, and y is the current
time, then if ticks_diff(x, y) < 0 then event has missed a deadline (and e.g.
needs to executed ASAP or skipped). Returning in this case a large unsigned
number (like ticks_diff behaved previously) doesn't make sense, and such
"large unsigned number" can't be reliably detected per our definition of
ticks_* function (we don't expose to user level maximum value, it can be
anything, relatively small or relatively large).
In order to have more fine-grained control over how builtin functions are
constructed, the MP_DECLARE_CONST_FUN_OBJ macros are made more specific,
with suffix of _0, _1, _2, _3, _VAR, _VAR_BETEEN or _KW. These names now
match the MP_DEFINE_CONST_FUN_OBJ macros.
As long as a port implement mp_hal_sleep_ms(), mp_hal_ticks_ms(), etc.
functions, it can just use standard implementations of utime.sleel_ms(),
utime.ticks_ms(), etc. Python-level functions.
This refactors ujson.loads(s) to behave as ujson.load(StringIO(s)).
Increase in code size is: 366 bytes for unix x86-64, 180 bytes for
stmhal, 84 bytes for esp8266.
As per discussion in #2449, using write requests instead of read requests
for I2C.scan() seems to support a larger number of devices, especially
ones that are write-only. Even a read-only I2C device has to implement
writes in order to be able to receive the address of the register to read.
Adds check that LZ offsets fall into the sliding dictionary used. This
catches a case when uzlib.DecompIO with a smaller dictionary is used
to decompress data which was compressed with a larger dictionary.
Previously, this would lead to producing invalid data or crash, now
an exception will be thrown.
The delay_half parameter must be specified by the port to set up the
timing of the software SPI. This allows the port to adjust the timing
value to better suit its timing characteristics, as well as provide a
more accurate printing of the baudrate.
There is no need to take src_len and dest_len arguments. The case of
reading-only with a single output byte (originally src_len=1, dest_len>1)
is now handled by using the output buffer as the input buffer, and using
memset to fill the output byte into this buffer. This simplifies the
implementations of the spi_transfer protocol function.
The memory read/write I2C functions now take an optional keyword-only
parameter that specifies the number of bits in the memory address.
Only mem-addrs that are a multiple of 8-bits are supported (otherwise
the behaviour is undefined).
Due to the integer type used for the address, for values larger than 32
bits, only 32 bits of address will be sent, and the rest will be padded
with 0s. Right now no exception is raised when that happens. For values
smaller than 8, no address is sent. Also no exception then.
Tested with a VL6180 sensor, which has 16-bit register addresses.
Due to code refactoring, this patch reduces stmhal and esp8266 builds
by about 50 bytes.
When the clock is too fast for the i2c slave, it can temporarily hold
down the scl line to signal to the master that it needs to wait. The
master should check the scl line when it is releasing it after
transmitting data, and wait for it to be released.
This change has been tested with a logic analyzer and an i2c slace
implemented on an atmega328p using its twi peripheral, clocked at 8Mhz.
Without the change, the i2c communication works up to aboy 150kHz
frequency, and above that results in the slave stuck in an unresponsive
state. With this change, communication has been tested to work up to
400kHz.
Adds horizontal scrolling. Right now, I'm just leaving the margins
created by the scrolling as they were -- so they will repeat the
edge of the framebuf. This is fast, and the user can always fill
the margins themselves.
Radomir Dopieralski
Damien George
Paul Sokolovsky
Alex March
Pavol Rusnak
Stefan Agner