Select ADC instance based on pin information to support ADC2 inputs.
Display ADC instance number similar to machine_adc (STM32H5 only):
<ADC2 on Pin(Pin.cpu.F14, mode=Pin.ANALOG) channel=6>
Signed-off-by: Rene Straub <rene@see5.ch>
Fixed the preliminary STM32H5 ADC support for pyb.ADC:
- Run ADC on PCLK/16.
- Use STM32 ADC library channel literals (__HAL_ADC_DECIMAL_NB_TO_CHANNEL).
- Use correct temperature conversion for H5 (30C, 130C calibration points).
Signed-off-by: Rene Straub <rene@see5.ch>
To simulate a partial erase, the code reads a native block, erases it,
and writes back the data before and after the erased area. However, the
current logic was filling the area after the erased block with data
from the beginning of the native block-aligned data, instead of applying
the proper offset.
Fixes#12474.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
If a board needs these outputs then it can define MICROPY_HW_CLK_PLLQ/R.
It saves power to not enable them if they are not needed.
Signed-off-by: Damien George <damien@micropython.org>
Supported from GCC 8 and up, and Compiler Explorer suggests it works as
expected with Clang since 3.6 (2014).
- Fixes situation where building embedded MicroPython with -O0 and
MICROPY_NLR_X64 crashes at runtime (due to nlr_push pushing the
frame pointer register EBP). Closes#12421.
- Allows removing the macOS tweak to undo pushing EBP onto the stack
in the generated function prelude.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Currently, check_esp_err() raises an exception without a location in the
source code, eg:
Traceback (most recent call last):
File "<stdin>", line 8, in <module>
OSError: (-258, 'ESP_ERR_INVALID_ARG')
This commit allows additional error reporting (function, line and file) to
be enabled via detailed exceptions. Change the error reporting config to
#define MICROPY_ERROR_REPORTING (MICROPY_ERROR_REPORTING_DETAILED)
and then exception messages from IDF errors look like:
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
OSError: (-258, "0x0102 ESP_ERR_INVALID_ARG in function 'set_duty_u16'
at line 342 in file './machine_pwm.c'")
Signed-off-by: Ihor Nehrutsa <IhorNehrutsa@gmail.com>
Fixes are:
- Reset the module first before changing GPIO1 direction.
- Skip spurious bytes received after reset.
- Use HCI UART ID and baudrate when reinitializing UART.
- Disable all printf output which causes unit-tests to fail.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
Fixes are:
- The baudrate argument is a keyword arg, it was passed before as a
positional arg.
- Use the port and baudrate arguments passed from higher level code instead
of the hard-coded port ID and baudrate, which would allow HCI drivers to
change baudrates.
- Increase UART char timeout and RX buffer size.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This is a host driver for ESP32 chips running the esp-hosted firmware,
which turns ESP32s into a WLAN/BT co-processor.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This patch generates a binary firmware image (*.bin) and removes the split
TEXT1/0_ADDR/SECTIONS because it's not configured for this port so it
generates broken binaries.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
Newer MCU series have additional fields in the struct which need to be
initialised to zero, eg Break2AFMode on WB55.
This work was funded by Planet Innovation.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
Increase asyncio tests timeouts to account for different WiFi modules and
CPU clocks on different boards.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
sdkconfig.base: Add CONFIG_BOOTLOADER_SKIP_VALIDATE_IN_DEEP_SLEEP=y.
This reduces time to boot from deepsleep by at least 200ms and can
provide significant power savings for deepsleep-based battery
applications.
docs/library/esp32.rst: Add note cautioning not to enter deepsleep after
changing the boot partition, without first performing a hard reset.
Signed-off-by: Glenn Moloney <glenn.moloney@gmail.com>
And use it in the Bluetooth bindings instead of setting the baudrate by a
call to the NXP lib.
Also fixes machine_uart.c to work with a baud rate of 921600.
Signed-off-by: robert-hh <robert@hammelrath.com>
Rene Straub
Luca Burelli
Damien George
Angus Gratton
IhorNehrutsa
iabdalkader
Andrew Leech
Glenn Moloney
dependabot[bot]
robert-hh
Seon Rozenblum
Jim Mussared