All 4 opcodes that can have caching bytes also have qstrs, so the test for
them must go in the qstr part of the code. The reason this incorrect
calculation of the opcode size did not lead to a bug is because the caching
byte is at the end of the opcode (byte, qstr, qstr, cache) and is always
0x00 when saving/loading, so was just treated as a single byte no-op
opcode. Hence these opcodes were being saved/loaded/decoded correctly.
Thanks to @malinah for finding the problem and providing the initial patch.
Header files that are considered internal to the py core and should not
normally be included directly are:
py/nlr.h - internal nlr configuration and declarations
py/bc0.h - contains bytecode macro definitions
py/runtime0.h - contains basic runtime enums
Instead, the top-level header files to include are one of:
py/obj.h - includes runtime0.h and defines everything to use the
mp_obj_t type
py/runtime.h - includes mpstate.h and hence nlr.h, obj.h, runtime0.h,
and defines everything to use the general runtime support functions
Additional, specific headers (eg py/objlist.h) can be included if needed.
Taking the address of a local variable leads to increased stack usage, so
the mp_decode_uint_skip() function is added to reduce the need for taking
addresses. The changes in this patch reduce stack usage of a Python call
by 8 bytes on ARM Thumb, by 16 bytes on non-windowing Xtensa archs, and by
16 bytes on x86-64. Code size is also slightly reduced on most archs by
around 32 bytes.
This patch allows the following code to run without allocating on the heap:
super().foo(...)
Before this patch such a call would allocate a super object on the heap and
then load the foo method and call it right away. The super object is only
needed to perform the lookup of the method and not needed after that. This
patch makes an optimisation to allocate the super object on the C stack and
discard it right after use.
Changes in code size due to this patch are:
bare-arm: +128
minimal: +232
unix x64: +416
unix nanbox: +364
stmhal: +184
esp8266: +340
cc3200: +128
Now, passing a keyword argument that is not expected will correctly report
that fact. If normal or detailed error messages are enabled then the name
of the unexpected argument will be reported.
This patch decreases the code size of bare-arm and stmhal by 12 bytes, and
cc3200 by 8 bytes. Other ports (minimal, unix, esp8266) remain the same in
code size. For terse error message configuration this is because the new
message is shorter than the old one. For normal (and detailed) error
message configuration this is because the new error message already exists
in py/objnamedtuple.c so there's no extra space in ROM needed for the
string.
Instead of caching data that is constant (code_info, const_table and
n_state), store just a pointer to the underlying function object from which
this data can be derived.
This helps reduce stack usage for the case when the mp_code_state_t
structure is stored on the stack, as well as heap usage when it's stored
on the heap.
The downside is that the VM becomes a little more complex because it now
needs to derive the data from the underlying function object. But this
doesn't impact the performance by much (if at all) because most of the
decoding of data is done outside the main opcode loop. Measurements using
pystone show that little to no performance is lost.
This patch also fixes a nasty bug whereby the bytecode can be reclaimed by
the GC during execution. With this patch there is always a pointer to the
function object held by the VM during execution, since it's stored in the
mp_code_state_t structure.
MP_BC_NOT was removed and the "not" operation made a proper unary
operator, and the opcode format table needs to be updated to reflect
this change (but actually the change is only cosmetic).
This allows the mp_obj_t type to be configured to something other than a
pointer-sized primitive type.
This patch also includes additional changes to allow the code to compile
when sizeof(mp_uint_t) != sizeof(void*), such as using size_t instead of
mp_uint_t, and various casts.
MICROPY_PERSISTENT_CODE must be enabled, and then enabling
MICROPY_PERSISTENT_CODE_LOAD/SAVE (either or both) will allow loading
and/or saving of code (at the moment just bytecode) from/to a .mpy file.
This patch gets full function argument passing working with native
emitter. Includes named args, keyword args, default args, var args
and var keyword args. Fully Python compliant.
It reuses the bytecode mp_setup_code_state function to do all the hard
work. This function is slightly adjusted to accommodate native calls,
and the native emitter is forced a bit to emit similar prelude and
code-info as bytecode.
This saves a lot of RAM for 2 reasons:
1. For functions that don't have default values, var args or var kw
args (which is a large number of functions in the general case), the
mp_obj_fun_bc_t type now fits in 1 GC block (previously needed 2 because
of the extra pointer to point to the arg_names array). So this saves 16
bytes per function (32 bytes on 64-bit machines).
2. Combining separate memory regions generally saves RAM because the
unused bytes at the end of the GC block are saved for 1 of the blocks
(since that block doesn't exist on its own anymore). So generally this
saves 8 bytes per function.
Tested by importing lots of modules:
- 64-bit Linux gave about an 8% RAM saving for 86k of used RAM.
- pyboard gave about a 6% RAM saving for 31k of used RAM.
Code-info size, block name, source name, n_state and n_exc_stack now use
variable length encoded uints. This saves 7-9 bytes per bytecode
function for most functions.
Damien George
Stefan Naumann
Alexander Steffen
Paul Sokolovsky
stijn