All board pins that have UART's assigned can be used. Baud rate range is
75 Baud to ~2 MBaud.
No flow control yet, and only RX is buffered. TX buffer and flow control
may be added later for SAMD51 with its larger RAM and Flash.
Its API conforms to the docs. There are 16 IRQ channels available, which
will be used as assignable to the GPIO numbers. In most cases, the irq
channel is GPIO_no % 16.
Changes are:
- Have two separate tables for SAM21 and SAMD51.
- Use a short table for SAMD21.
- Add a comment to each line telling what it's for, making further use
easier.
- Add preliminary handlers/entries for PendSV, EIC and Sercom. These will
be replaced later when the respecitve modules are added.
Features are:
- 3 to 5 different frequency groups.
- Freq range of 1Hz - 24 MHz.
- Duty rate stays stable on freq change.
Keyword options to the PWM constructor:
- device=n Select a specific PWM device. If no device is specified, a free
device is chosen, if available at that pin.
- freq=nnnn
- duty_u16=nnnn
- duty_ns=nnnn
- invert=True/False Allowing two outputs on the same device/channel to have
complementary signals.
If both freq and duty are provided, PWM output will start immediately.
Pins at the same device have the same frequency. If the PWM output number
exceeds the number of channels at the PWM device, the effctive channel_no
is output_no % channel_count. So with a channel count of 4, output 7 is
assigned to channel 3. Pins at a certain channel have the same frequency
and duty rate, but may be seperately inverted.
With the method read_u16(). Keyword arguments of the constructor are:
- bits=n The resolution; default is 12.
- average=n The average of samples, which are taken and cumulated. The
default value is 16. Averaging by hw is faster than averaging
in code.
The ADC runs at a clock freq 1.5 MHz. A single 12 bit conversion takes
8 microseconds.
The pin af table is a representation of the MUX table from the data sheet.
It provides information for each pin about the supported device functions.
That information is needed by pin.irq, machine.ADC, machine.PWM,
machine.UART, machine.SPI and machine.I2C. For each of these, the table
tells for each pin, which device number, af number and pad number is
assigned. Using the table gives a straight, uniform access to the
information, where the benefit outweights the size of the table, which is
not that large.
The tables are MCU-specific. It is not required to tell for each board,
which and where each of the above devices is available. That makes addding
boards easy.
Note: The information for DAC and I2S was not included, since it affects
only a few pins.
Changes in this commit are:
- Use mphal_xx functions whenever possible.
- Remove obsolete includes.
- Clean up traces of a non-functional pin.irq() from earlier builds.
Pin.irq() will be added in further commits in a working manner.
The changes in this commit are:
- Add an interface for pin open-drain mode.
- Improve ticks_us() by using the us-counter.
- Improve ticks_cpu() by using the CPU's SysTick.
Clock settings:
- GCLK0: 48 MHz (SAMD21) or 120 MHz(SAMD51).
- GCLK1: 32768 Hz for driving the PLL.
- GCLK2: 48 MHz for tzhe peripheral clock.
- GCLK3: 1 MHz (SAMD21) or 8 MHz (SAMD51) for the µs ticks timer.
- GCLK8: 1 kHz for WDT (SAMD21 only).
If a 32 kHz crystal is present, it will be used as clock source. Otherwise
the DFLL48M in open-loop mode is used.
GCLK0 for SAM51 can be changed between 48 MHz and 200 MHz. The specified
range is 96 MHz - 120 MHz.
These two boards are used for testing, so it is favorable to have them
added early.
The full test set is:
- ADAFRUIT_FEATHER_M4_EXPRESS: SAMD51 with 32kHz crystal.
- ADAFRUIT_ITSYBITSY_M0_EXPRESS: SAMD21 without crystal.
- ADAFRUIT_ITSYBITSY_M4_EXPRESS: SAMD51 without crystal.
- SEEED_XIAO: SAM21 with 32kHz crystal.
Auto DMA channel is supported in IDF v4.4, and is required to be used on S3
chips, so use this simpler configuration option where possible.
Fixes issue #8634.
Signed-off-by: Damien George <damien@micropython.org>
Updates all README.md and docs, and manifests to `require("mip")`.
Also extend and improve the documentation on freezing and packaging.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This uses the frozentest.mpy that is also used by ports/minimal.
Also fixes two bugs that these new tests picked up:
- File extension matching in manifestfile.py.
- Handling of freeze_mpy results in makemanifest.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
frozentest.mpy was previously duplicated in ports/minimal and
ports/powerpc.
This needs to be re-generated on every .mpy version increase, so might as
well just have a single copy of it.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Instead of being an explicit field, it's now a slot like all the other
methods.
This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The goal here is to remove a slot (making way to turn make_new into a slot)
as well as reduce code size by the ~40 references to mp_identity_getiter
and mp_stream_unbuffered_iter.
This introduces two new type flags:
- MP_TYPE_FLAG_ITER_IS_ITERNEXT: This means that the "iter" slot in the
type is "iternext", and should use the identity getiter.
- MP_TYPE_FLAG_ITER_IS_CUSTOM: This means that the "iter" slot is a pointer
to a mp_getiter_iternext_custom_t instance, which then defines both
getiter and iternext.
And a third flag that is the OR of both, MP_TYPE_FLAG_ITER_IS_STREAM: This
means that the type should use the identity getiter, and
mp_stream_unbuffered_iter as iternext.
Finally, MP_TYPE_FLAG_ITER_IS_GETITER is defined as a no-op flag to give
the default case where "iter" is "getiter".
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This will always have the maximum/minimum size of a mp_obj_type_t
representation and can be used as a member in other structs.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The buffer protocol type only has a single member, and this existing layout
creates problems for the upcoming split/slot-index mp_obj_type_t layout
optimisations.
If we need to make the buffer protocol more sophisticated in the future
either we can rely on the mp_obj_type_t optimisations to just add
additional slots to mp_obj_type_t or re-visit the buffer protocol then.
This change is a no-op in terms of generated code.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
In that case, no Pin will be configured for the CS signal, even if it is
internally still generated. That setting allows to use any pin for CS,
which then must be controlled by the Python script.
Also make the default cs=-1 to match other ports (software CS).
The new teensy loader keeps the file system under certain conditions:
- The file size is properly set in the file header.
- The header version is 4.3
These changes are implemented here, requiring a backport of
fsl_flexspi_nor_boot.c. There is still a problem with the command line
version of the teensy loader, which fails on the first attempt. At the
second attempt it works. The GUI version of the teensy loader is fine.
All variants (except minimal) enable text compression and fat/lfs, so move
them to the common mpconfigport.mk.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is a no-op for coverage and minimal.
The standard and dev variants have been merged and enable the same feature
set as a typical bare-metal board. And remove the CI for the dev build.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The freedos variant is untested by CI and is difficult to maintain. The
fast variant is not a good name for what it does.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
I.e. for whichever SPI/I2C instance is PICO_DEFAULT_I2C, there's no need to
set MICROPY_HW_SPIn_SCK.
The only ones remaining are for the non-default instance.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
In most cases, it's calculated automatically from the board name, and so
doesn't need to be set at all.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Since L4 HAL version 1.17.0, HAL_TIM_IC_Start_IT() checks whether specified
channel of timer is busy or not, which is the case if this function is
called more than once without first calling HAL_TIM_IC_Stop_IT(). The fix
in this commit is to call the stop function before calling start. The PWM
and OC modes have the same issue with the same fix.
Fixes issue #8732.
Prior to this commit, excuting this code:
i2c = I2C(1, I2C.CONTROLLER, dma=True)
i2c.send(data, addr=i2c_addr)
the call to i2c.send() does not return and the board needs a reset. This
code works when dma=False.
According to the specification, I2Cx_EV_IRQHandler should:
- Write DR to address when Start condition generated.
- Clear ADDR by reading SR2 after reading SR2 when address sent.
These processes are included in HAL_I2C_EV_IRQHandler(), however the
firmware size increses about 2KB if HAL_I2C_EV_IRQHandler is called. This
commit adds above processes to i2c_ev_irq_handler, and increases firmware
by less than 100 bytes.
Fixes issue #2643.
pyb.ADC(channel) checks whether specified channel is valid or have ADC
capability but pyb.ADCAll().read_channel() does not.
This change adds checking whether specified channel is valid and throw
ValueError if channel is invalid. This is same as pyb.ADC().
Although this driver and associated hardware can be used on any board, it
makes to only freeze it for PYB and PYBD boards. It can be easily copied
to any board if needed.
Fixes issue #8056.
Signed-off-by: Damien George <damien@micropython.org>
Changes in this commit:
- Manifest include's now use the directory path where possible (no longer
necessary to include the manifest.py file explicitly).
- Add manifest.py for all drivers and components that are referenced by
port/board manifests.
- Replace all uses of freeze() with package()/module(), except for port and
board modules.
- Use opt=3 everywhere, for consistency and to reduce code size.
- Use require() instead of include() for all micropython-lib references.
- Remove support for optional board-level manifest.py in mimxrt port, to
make it behave the same as other ports (the board must set
FROZEN_MANIFEST to a custom manifest.py, which can optionally include the
default, port-level manifest).
- Also reinstates modules that were accidentally removed from the esp8266
512k build in fbe9417b90.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
micropython-lib is now a submodule, and the manifest compilation process
will ensure it is available, so manifests no longer need to check that it
is available.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
uart.flush()
flush() will wait until all characters have been sent.
To avoid a permanent lock, a timeout applies depending on the
size of FIFO and the baud rate.
ret = uart.txdone()
ret is True if no transfer is in progress.
ret is False otherwise.
Since uart.write() of the nrf port waits until all bytes but the last
one have been sent, uart.flush() and uart.txdone() are implemented
as empty functions to provide API consistency.
uart.flush()
flush() will always return immediately, even if the last byte
may still be sent.
ret = uart.txdone()
uart.txdone() will always return True, even if the last byte
may still be sent.
Since uart.write() of the STM32 port waits until all bytes have
been sent, uart.flush() and uart.txdone() are implemented as empty
functions to provide API consistency.
uart.flush()
flush() will always return immediately.
ret = uart.txdone()
uart.txdone() will always return True.
uart.flush()
flush() will wait until all characters but the last one have been sent.
It returns while the last character is sent. If needed, the calling
code has to add one character wait time. To avoid a permanent lock,
a timeout applies depending on the size of the FIFO and the baud rate.
ret = uart.txdone()
ret is True if no transfer is in progress. It returns already True when
the last byte of a transfer is sent.
ret is False otherwise.
uart.flush()
flush() will wait until all characters have been sent.To avoid a
permanent lock, a timeout applies depending on the size of txbuf
and the baud rate.
ret = uart.txdone()
ret is True if no transfer is in progress.
ret is False otherwise.
uart.flush()
flush() will wait until all characters have been sent.To
avoid a permanent lock, a timeout applies depending on the
size of txbuf and the baud rate.
ret = uart.txdone()
ret is True if no transfer is in progress.
ret is False otherwise.
uart.flush()
flush() will wait until all characters have been sent. It may return
while the last character is sent. if needed, the calling code has to
add one character wait time. To avoid a permanent lock, a timeout
applies depending on the size of txbuf and the baud rate.
ret = uart.txdone()
ret is True if no transfer is in progress. It may return True if the
last byte of a transfer is sent.
ret is False otherwise.
Changes are:
- Remove unix- and stm32-specific sections (move unix to its own
README.md), stm32 was duplicated.
- Add links to GitHub Discussions and Discord.
- Update information about the project.
- Add a getting started section.
- Explain `make submodules`.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
So that everything is reset and the SD card can be created again after
calling SDCard.deinit() (and after a soft reset).
Fixes issue #8949.
Signed-off-by: Damien George <damien@micropython.org>
Having two separate manifests is confusing. It's simpler to have the daily
builds use the same configuration as the stable, release builds.
Signed-off-by: Damien George <damien@micropython.org>
The new `mp_obj_new_str_from_utf8_vstr` can be used when you know you
already have a unicode-safe string.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Previously the desired output type was specified. Now make the type part
of the function name. Because this function is used in a few places this
saves code size due to smaller call-site.
This makes `mp_obj_new_str_type_from_vstr` a private function of objstr.c
(which is almost the only place where the output type isn't a compile-time
constant).
This saves ~140 bytes on PYBV11.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The existing non-Docker instructions are basically impossible to follow
because the esp-open-sdk does not compile. Update these instructions to
use the exact toolchain that our CI uses.
Also split the Docker from non-Docker instructions, to avoid confusion
about which commands need to be prefixed.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
It has been about 8 years since support for this chip was added. Reasons
to remove it are:
- It is no longer easy to obtain this part.
- There are now many other options for WiFi.
- It's not a good use of developer time to maintain it.
Signed-off-by: Damien George <damien@micropython.org>
Not safe to use mp_hal_delay_ms before boot if threading is enabled,
because threading will not have been initialised, and
MICROPY_EVENT_POLL_HOOK assumes threading is initialised.
HAL_Delay doesn't call MICROPY_EVENT_POLL_HOOK, but is still
power-efficient like mp_hal_delay_ms (unlike mp_hal_delay_us).
Fixes#7816.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Rather than having the autobuild know about the particular variants, have
the mpconfigboard.mk describe them and make autobuild discover them
automatically.
Adds a "query-variants" target to stm32/Makefile to allow the set of
possible variants to be queried.
Removes pybv3 from the autobuild as this isn't use by the downloads page.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
If mboot is built with support for packing (signing/encryption) it needs up
to 32KiB. So for simplicity increase the mboot region to 32KiB
unconditionally for WB55 boards (custom WB55 board configurations can still
provide their own linker scripts to override this).
It used to be 10 bit times, which is too short. The break state must be
longer than a regular character time, at least 13 bit times. This is now
implemented by reducing the baudrate while sending the "0". The break time
will now vary with data length and parity setting, but will at least be 15
bit times.
Tested with a GENERIC_SPIRAM, GENERIC_C3 and UM_TINYS2 board.
Set the channel with esp_wifi_set_channel(), which adds support for setting
the channel of the STA interface
Get the channel with esp_wifi_get_channel() which returns the actual wifi
channel of the radio, rather than the configured channel.
robert-hh
Damien George
Jim Mussared
Matt Trentini
yn386
Jatty_
Andrew Leech
Phil Howard
Takeo Takahashi
hoihu
Damiano Mazzella
glenn20