The buffer protocol type only has a single member, and this existing layout
creates problems for the upcoming split/slot-index mp_obj_type_t layout
optimisations.
If we need to make the buffer protocol more sophisticated in the future
either we can rely on the mp_obj_type_t optimisations to just add
additional slots to mp_obj_type_t or re-visit the buffer protocol then.
This change is a no-op in terms of generated code.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
In that case, no Pin will be configured for the CS signal, even if it is
internally still generated. That setting allows to use any pin for CS,
which then must be controlled by the Python script.
Also make the default cs=-1 to match other ports (software CS).
The new teensy loader keeps the file system under certain conditions:
- The file size is properly set in the file header.
- The header version is 4.3
These changes are implemented here, requiring a backport of
fsl_flexspi_nor_boot.c. There is still a problem with the command line
version of the teensy loader, which fails on the first attempt. At the
second attempt it works. The GUI version of the teensy loader is fine.
This is a latent issue that wasn't caught by CI because there was no
configuration that had both stackless+uasyncio.
The previous check to skip with stackless builds only worked when the
bytecode emitter was used by default. Force the check to use the bytecode
emitter.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
All variants (except minimal) enable text compression and fat/lfs, so move
them to the common mpconfigport.mk.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is a no-op for coverage and minimal.
The standard and dev variants have been merged and enable the same feature
set as a typical bare-metal board. And remove the CI for the dev build.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The freedos variant is untested by CI and is difficult to maintain. The
fast variant is not a good name for what it does.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
When iterating over filesystem/folders with os.iterdir(), an open file
(directory) handle is used internally. Currently this file handle is only
closed once the iterator is completely drained, eg. once all entries have
been looped over / converted into list etc.
If a program opens an iterdir but does not loop over it, or starts to loop
over the iterator but breaks out of the loop, then the handle never gets
closed. In this state, when the iter object is cleaned up by the garbage
collector this open handle can cause corruption of the filesystem.
Fixes issues #6568 and #8506.
In case the version from pypi is installed or some other version is
available in sys.path, prepend `$(TOP)/mpy-cross` to sys.path instead.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is technically a breaking change, but:
a) We need the end handle to do descriptor discovery properly.
b) We have no possible use for the existing definition handle in the
characteristic result IRQ. None of the methods can use it, and therefore
no existing code should be using it in a way that changing it to a
different integer value should break.
Unfortunately NimBLE doesn't make it easy to get the end handle, so also
implement a mechanism to use the following characteristic to calculate
the previous characteristic's end handle.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Incorrect use of "continue" when the tuple was length zero meant it
broke the rest of the argument handling.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Previous the build directory just used the board name, now make it use the
variant name too.
This shouldn't have any change because the existing directory should not
exist (all builds run by these scripts remove their build directory after
completion), but it makes debugging easier.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
I.e. for whichever SPI/I2C instance is PICO_DEFAULT_I2C, there's no need to
set MICROPY_HW_SPIn_SCK.
The only ones remaining are for the non-default instance.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
In most cases, it's calculated automatically from the board name, and so
doesn't need to be set at all.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Since L4 HAL version 1.17.0, HAL_TIM_IC_Start_IT() checks whether specified
channel of timer is busy or not, which is the case if this function is
called more than once without first calling HAL_TIM_IC_Stop_IT(). The fix
in this commit is to call the stop function before calling start. The PWM
and OC modes have the same issue with the same fix.
Fixes issue #8732.
Prior to this commit, excuting this code:
i2c = I2C(1, I2C.CONTROLLER, dma=True)
i2c.send(data, addr=i2c_addr)
the call to i2c.send() does not return and the board needs a reset. This
code works when dma=False.
According to the specification, I2Cx_EV_IRQHandler should:
- Write DR to address when Start condition generated.
- Clear ADDR by reading SR2 after reading SR2 when address sent.
These processes are included in HAL_I2C_EV_IRQHandler(), however the
firmware size increses about 2KB if HAL_I2C_EV_IRQHandler is called. This
commit adds above processes to i2c_ev_irq_handler, and increases firmware
by less than 100 bytes.
Fixes issue #2643.
pyb.ADC(channel) checks whether specified channel is valid or have ADC
capability but pyb.ADCAll().read_channel() does not.
This change adds checking whether specified channel is valid and throw
ValueError if channel is invalid. This is same as pyb.ADC().
Although this driver and associated hardware can be used on any board, it
makes to only freeze it for PYB and PYBD boards. It can be easily copied
to any board if needed.
Fixes issue #8056.
Signed-off-by: Damien George <damien@micropython.org>
Changes in this commit:
- Manifest include's now use the directory path where possible (no longer
necessary to include the manifest.py file explicitly).
- Add manifest.py for all drivers and components that are referenced by
port/board manifests.
- Replace all uses of freeze() with package()/module(), except for port and
board modules.
- Use opt=3 everywhere, for consistency and to reduce code size.
- Use require() instead of include() for all micropython-lib references.
- Remove support for optional board-level manifest.py in mimxrt port, to
make it behave the same as other ports (the board must set
FROZEN_MANIFEST to a custom manifest.py, which can optionally include the
default, port-level manifest).
- Also reinstates modules that were accidentally removed from the esp8266
512k build in fbe9417b90.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
The metadata can be version, description, and license.
After executing a manifest, the top-level metadata can be queried, and also
each file output from the manifest will have the metadata of the
containing manifest.
Use the version metadata to "tag" files before freezing such that they have
__version__ available.
Jim Mussared
Damien George
robert-hh
Wind-stormger
Andrew Leech
Phil Howard
Jeff Epler
yn386