This is necessary to access sites that only support these protocols.
The rp2 port already has ECDH enabled, so this just adds ECDSA there. The
other ports now gain both ECDH and ECDSA. The code size increase is:
- rp2 (PICO_W): +2916 bytes flash, +24 bytes BSS
- stm32 (PYBD_SF6): +20480 bytes flash, +32 bytes data, +48 bytes BSS
- mimxrt (TEENSY41): +20708 bytes flash, +32 bytes data, +48 bytes BSS
- unix (standard x86-64): +39344 executable, +1744 bytes data, +96 BSS
This is obviously a large increase in code size. But there doesn't seem to
be any other option because without elliptic curve cryptography devices are
partially cut off from the internet. For use cases that require small
firmware size, they'll need to build custom firmware with a custom mbedtls
config.
Signed-off-by: Damien George <damien@micropython.org>
Updates all README.md and docs, and manifests to `require("mip")`.
Also extend and improve the documentation on freezing and packaging.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Instead of being an explicit field, it's now a slot like all the other
methods.
This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The goal here is to remove a slot (making way to turn make_new into a slot)
as well as reduce code size by the ~40 references to mp_identity_getiter
and mp_stream_unbuffered_iter.
This introduces two new type flags:
- MP_TYPE_FLAG_ITER_IS_ITERNEXT: This means that the "iter" slot in the
type is "iternext", and should use the identity getiter.
- MP_TYPE_FLAG_ITER_IS_CUSTOM: This means that the "iter" slot is a pointer
to a mp_getiter_iternext_custom_t instance, which then defines both
getiter and iternext.
And a third flag that is the OR of both, MP_TYPE_FLAG_ITER_IS_STREAM: This
means that the type should use the identity getiter, and
mp_stream_unbuffered_iter as iternext.
Finally, MP_TYPE_FLAG_ITER_IS_GETITER is defined as a no-op flag to give
the default case where "iter" is "getiter".
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
I.e. for whichever SPI/I2C instance is PICO_DEFAULT_I2C, there's no need to
set MICROPY_HW_SPIn_SCK.
The only ones remaining are for the non-default instance.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
In most cases, it's calculated automatically from the board name, and so
doesn't need to be set at all.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Changes in this commit:
- Manifest include's now use the directory path where possible (no longer
necessary to include the manifest.py file explicitly).
- Add manifest.py for all drivers and components that are referenced by
port/board manifests.
- Replace all uses of freeze() with package()/module(), except for port and
board modules.
- Use opt=3 everywhere, for consistency and to reduce code size.
- Use require() instead of include() for all micropython-lib references.
- Remove support for optional board-level manifest.py in mimxrt port, to
make it behave the same as other ports (the board must set
FROZEN_MANIFEST to a custom manifest.py, which can optionally include the
default, port-level manifest).
- Also reinstates modules that were accidentally removed from the esp8266
512k build in fbe9417b90.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
micropython-lib is now a submodule, and the manifest compilation process
will ensure it is available, so manifests no longer need to check that it
is available.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
uart.flush()
flush() will wait until all characters have been sent. It may return
while the last character is sent. if needed, the calling code has to
add one character wait time. To avoid a permanent lock, a timeout
applies depending on the size of txbuf and the baud rate.
ret = uart.txdone()
ret is True if no transfer is in progress. It may return True if the
last byte of a transfer is sent.
ret is False otherwise.
Previously the desired output type was specified. Now make the type part
of the function name. Because this function is used in a few places this
saves code size due to smaller call-site.
This makes `mp_obj_new_str_type_from_vstr` a private function of objstr.c
(which is almost the only place where the output type isn't a compile-time
constant).
This saves ~140 bytes on PYBV11.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Figure out path to arm-none-eabi-size the same way it's done for the
other binaries, instead of assuming it to be in the user's $PATH.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Create a new linker section .unitialized_bss for bss that does not need
zero-initialising.
Move gc_heap to this section, which saves ~30ms from rising edge of RESET
to setting a pin HIGH in MicroPython.
Zero fill happens in Pico SDK crt0.S before ROSC is configured. It's very,
very slow.
Signed-off-by: Phil Howard <phil@gadgetoid.com>
The ntptime module was previously only included in the ESP8266 port. This
commit factors that module out into the extmod directory, makes it support
different epochs, and includes it in the rp2 port.
Used to be special-cased for Pico, but now everything depends on
micropython-lib if it's using a frozen manifest.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Still see some USB issues apparently caused by delays loading wifi
firmware. cyw43_delay_ms is used to wait in the driver, so we should call
the event hook in there.
Fixes#8963.
The state machines were not properly restarted in the case that the same
PIO program was shared among multiple StateMachine instances. This is
because only the first StateMachine to use the program would set the
rp2_state_machine_initial_pc variable.
See https://forum.micropython.org/viewtopic.php?f=21&t=12776&p=69464#p69464
Originally in drivers/ninaw10/nina_wifi_bsp.c but that isn't a QSTR source.
Also remove outdated commment about root pointers in mpconfigport.h.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is a statically-allocated UART (see machine_uart.c), and doesn't
contain any heap pointers other than the ringbufs (which are already root
pointers), so no need to track it additionally.
Saves needing to add mpbthciport.c to the QSTR sources.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
rp2: change tud_task() to tud_task_ext().
mimxrt: use lib/tinyusb/src/portable/chipidea/ci_hs/dcd_ci_hs.c instead of
lib/tinyusb/src/portable/nxp/transdimension/dcd_transdimension.c.
nrf: add a definition for the changed tud_task(). tud_task() is changed
to tud_task_ext(), and the #define for backward compatibility is in
src/device/usbd.h.
The items I know which are fixed with this version:
- Fix for the SAMD USB lock-up.
- Support the MIMXRT11XX series of MCUs.
- Fix a wrong pin definition for MIMXRT1050_EVKB.
Tested with the MIMXRT boards, rp2 Pico, SAMD boards, nrf board.
All ports that use mbedtls use the custom error messages in
mp_mbedtls_errors.c. This commit simplifies the build so that ports don't
need to explicitly add this file, it's now used by default when mbedtls is
enabled.
Signed-off-by: Damien George <damien@micropython.org>
All in-tree uses of MICROPY_PORT_ROOT_POINTERS have been replaced with
MP_REGISTER_ROOT_POINTER(), so now we can remove both
MICROPY_PORT_ROOT_POINTERS and MICROPY_BOARD_ROOT_POINTERS from the code
and remaining config files.
Signed-off-by: David Lechner <david@pybricks.com>
This uses MP_REGISTER_ROOT_POINTER() to register mod_network_nic_list and
removes the same from all mpconfigport.h.
Signed-off-by: David Lechner <david@pybricks.com>
This uses MP_REGISTER_ROOT_POINTER() to register bluetooth_nimble_memory
and bluetooth_nimble_root_pointers and removes the same from all
mpconfigport.h.
Signed-off-by: David Lechner <david@pybricks.com>
This uses MP_REGISTER_ROOT_POINTER() to register mp_wifi_spi, mp_wifi_timer
and mp_wifi_sockpoll_list and removes the same from all mpconfigport.h.
Signed-off-by: David Lechner <david@pybricks.com>
This uses MP_REGISTER_ROOT_POINTER() to register the readline_history root
pointer array used by shared/readline.c and removes the registration from
all mpconfigport.h files.
This also required adding a new MICROPY_READLINE_HISTORY_SIZE config option
since not all ports used the same sized array.
Signed-off-by: David Lechner <david@pybricks.com>
Commit 0e28a1f0e5 made it possible to set
-march=armv6m. It needs to be used when freezing for rp2.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Damien George
iabdalkader
robert-hh
Jim Mussared
Matt Trentini
Phil Howard
hoihu
Jacob Siverskog
omogenot
Ian Davies
Peter Harper
David Lechner