Commit Graph

224 Commits

Author SHA1 Message Date
iabdalkader fabfacf3d7 stm32/boards: Add new NUCLEO_H743ZI board configuration files.
USB serial and mass storage works, and the REPL is also available via the
UART through the on-board ST-LINK.
2018-03-09 15:08:11 +11:00
Damien George 8522874167 stm32/boards: Add stm32h743.ld linker script. 2018-03-09 15:08:11 +11:00
Damien George a3c721772e stm32/boards: Add stm32h743_af.csv file describing H7 GPIO alt funcs. 2018-03-09 14:06:34 +11:00
Damien George 0b88a9f02e unix/coverage: Allow coverage tests to pass with debugging disabled. 2018-03-08 12:49:31 +11:00
sec2 250b24fe36 stm32/boards/NUCLEO_F767ZI: Update pins list to include 3 extra pins. 2018-03-07 18:53:02 +11:00
sec2 bda3620616 stm32/boards/stm32f767_af.csv: Add ADC column to pin capability list. 2018-03-07 18:40:06 +11:00
Damien George 024edafea0 stm32/i2c: On F4 MCUs report the actual I2C SCL frequency. 2018-03-07 14:59:03 +11:00
Lee Seong Per 478ce8f7e3 esp32/modnetwork: Implement status('stations') to list STAs in AP mode.
The method returns a list of tuples representing the connected stations.
The first element of the tuple is the MAC address of the station.
2018-03-05 17:59:19 +11:00
Damien George d4470af239 esp32: Revert "esp32/machine_touchpad: Swap pins 32 and 33."
This reverts commit 5a82ba8e07.

Touch sensor 8 and 9 have a mismatch in some of their registers and this is
now fixed in software by the ESP IDF.
2018-03-05 14:06:45 +11:00
Olivier Ortigues b691aa0aae esp8266/esppwm: Always start timer to avoid glitch from full to nonfull.
The PWM at full value was not considered as an "active" channel so if no
other channel was used the timer used to mange PWM was not started.  So
when another duty value was set the PWM timer restarted and there was a
visible glitch when driving LEDs.  Such a glitch can be seen with the
following code (assuming active-low LED on pin 0):

    p = machine.PWM(machine.Pin(0))
    p.duty(1023) # full width, LED is off
    p.duty(1022) # LED flashes brightly then goes dim

This patch fixes the glitch.
2018-03-05 11:39:44 +11:00
Damien George adda38cf76 stm32/qspi: Add hardware QSPI driver, with memory-map capability.
It supports the abstract QSPI protocol defined in drivers/bus/qspi.h.
2018-03-03 00:17:08 +11:00
Damien George 8bd0a51ca9 stm32/spibdev: Convert to use multiple block read/write interface.
The spiflash driver now supports read/write of multiple blocks at a time.
2018-03-03 00:13:15 +11:00
Damien George 861080aa3d stm32/storage: Add option for bdev to supply readblock/writeblocks.
If the underlying block device supports it, it's more efficient to
read/write multiple blocks at once.
2018-03-02 23:57:53 +11:00
Damien George 0210383da5 stm32/spibdev: Add option to configure SPI block dev to use QSPI flash.
To use QSPI (in software QSPI mode) the configuration needed is:

    #define MICROPY_HW_SPIFLASH_SIZE_BITS (n * 1024 * 1024)
    #define MICROPY_HW_SPIFLASH_CS      (pin_x1)
    #define MICROPY_HW_SPIFLASH_SCK     (pin_x2)
    #define MICROPY_HW_SPIFLASH_IO0     (pin_x3)
    #define MICROPY_HW_SPIFLASH_IO1     (pin_x4)
    #define MICROPY_HW_SPIFLASH_IO2     (pin_x5)
    #define MICROPY_HW_SPIFLASH_IO3     (pin_x6)
2018-03-02 23:55:45 +11:00
Damien George a0dfc38641 stm32/spibdev: Update to work with new spiflash driver. 2018-03-02 23:55:40 +11:00
Damien George c607b58efe tests: Move heap-realloc-while-locked test from C to Python.
This test for calling gc_realloc() while the GC is locked can be done in
pure Python, so better to do it that way since it can then be tested on
more ports.
2018-03-02 10:59:09 +11:00
Damien George c3f1b22338 tests/unix: Add coverage tests for various GC calls. 2018-03-01 22:49:15 +11:00
Damien George d3cac18d49 tests/unix: Add coverage test for VM executing invalid bytecode. 2018-02-27 16:18:11 +11:00
Damien George c5fe610ba1 esp8266/modnetwork: Implement WLAN.status('rssi') for STA interface.
This will return the RSSI of the AP that the STA is connected to.
2018-02-26 16:41:13 +11:00
Damien George 01dcd5bb71 esp8266/uart: Allow to compile with event-driven REPL. 2018-02-26 16:10:27 +11:00
Damien George 62be14d77c tests/unix: Add coverage tests for mpz_set_from_float, mpz_mul_inpl.
These new tests cover cases that can't be reached from Python and get
coverage of py/mpz.c to 100%.

These "unreachable from Python" pieces of code could be removed but they
form an integral part of the mpz C API and may be useful for non-Python
usage of mpz.
2018-02-25 23:43:16 +11:00
Damien George 989fc16162 stm32: Move MCU-specific cfg from mphalport.h to mpconfigboard_common.h.
It's cleaner to have all the MCU-specific configuration in one location,
not least to help with adding support for a new MCU series.
2018-02-23 16:54:07 +11:00
Damien George ea05b400df stm32/flash: Use FLASH_TYPEPROGRAM_WORD to support newer HALs. 2018-02-23 16:30:47 +11:00
Damien George e6220618ce stm32: Use "GEN" for describing files generated in the build.
Instead of "Create", to match the build output from the py/ core.
2018-02-23 16:27:30 +11:00
Damien George 60b0982bb2 stm32: Add board config option to enable/disable the ADC.
The new option is MICROPY_HW_ENABLE_ADC and is enabled by default.
2018-02-22 14:22:45 +11:00
Damien George a36c700d9b minimal/Makefile: Explicitly include lib/utils/printf.c in build.
The bare-metal port needs it and it's no longer included by default since
the Makefile now uses $(PY_CORE_O).
2018-02-22 13:19:09 +11:00
Damien George 9df6451ec5 ports/{bare-arm,minimal}/Makefile: Only build with core source files.
These ports don't need anything from extmod so don't include those files
at all in the build.  This speeds up the build by about 10% when building
with a single core.
2018-02-22 12:48:51 +11:00
Damien George 82828340a0 ports: Enable ucollections.deque on relevant ports.
These ports are all capable of running uasyncio.
2018-02-21 22:55:13 +11:00
Damien George cced43feb8 esp32/modsocket: Allow getaddrinfo() to take up to 6 args.
Currently only the first 2 args are used, but this patch should at least
make getaddrinfo() signature-compatible with CPython and other bare-metal
ports that use the lwip bindings.
2018-02-21 19:09:38 +11:00
Damien George e600810f39 esp32/main: Allocate the uPy heap via malloc instead of on the bss.
This allows to get slightly more memory for the heap (currently around 110k
vs previous 92k) because the ESP IDF frees up some RAM after booting up.
2018-02-21 14:25:51 +11:00
Damien George c49a73ab0e esp32: Update to the latest ESP IDF.
This update requires a new ESP32 toolchain: 1.22.0-80-g6c4433a-5.2.0.
2018-02-21 14:24:10 +11:00
Damien George 27fa9881a9 esp32/modnetwork: Implement dhcp_hostname for WLAN.config(). 2018-02-19 17:02:56 +11:00
Damien George 5a82ba8e07 esp32/machine_touchpad: Swap pins 32 and 33.
Based on testing, this is how the mapping should be.
2018-02-19 00:36:55 +11:00
Damien George 60c6b880fa esp32/machine_rtc: Move export declaration from .c to common .h file. 2018-02-17 00:52:55 +11:00
Eric Poulsen abec47a1cd esp32/modesp32: Add new module "esp32" to support extra wake features.
The machine.Pin class is also updated to support these wake-on-pin
features.
2018-02-17 00:49:05 +11:00
Eric Poulsen 44033a1d27 esp32/machine_rtc: Add RTC class to machine module with sleep impl.
The machine.RTC class is added and the machine module is updated with the
implementation of sleep, deepsleep, reset_cause and wake_reason.
2018-02-17 00:47:17 +11:00
Damien George d966a33486 stm32: Change header include guards from STMHAL to STM32 to match dir. 2018-02-15 15:47:04 +11:00
Olivier Ortigues 359d2bdf84 esp8266/README.md: Update build instruction to reflect new ports dir. 2018-02-15 11:14:52 +11:00
Olivier Ortigues 5c83d05b49 esp8266/esppwm: Clip negative duty numbers to 0.
Prior to this patch a negative duty would lead to full PWM.
2018-02-15 11:12:41 +11:00
Damien George ab7819c314 unix/mpconfigport_coverage: Enable range (in)equality comparison. 2018-02-14 23:22:02 +11:00
Damien George 24c513cbc3 unix/Makefile,embedding/Makefile: Remove obsolete use of STMHAL_SRC_C. 2018-02-14 15:24:21 +11:00
Damien George e6235fe647 teensy: Update GPIO speed consts to align with changes in stm32 port. 2018-02-14 10:52:45 +11:00
Damien George fa13e0d35b stm32: Factor out flash and SPI block-device code to separate files.
Prior to this patch, storage.c was a combination of code that handled
either internal flash or external SPI flash and exposed one of them as a
block device for the local storage.  It was also exposed to the USB MSC.

This patch splits out the flash and SPI code to separate files, which each
provide a general block-device interface (at the C level).  Then storage.c
just picks one of them to use as the local storage medium.  The aim of this
factoring is to allow to add new block devices in the future and allow for
easier configurability.
2018-02-13 22:21:46 +11:00
Damien George 34911f1a57 stm32/boards: Update all boards to work with new USB configuration. 2018-02-13 18:57:01 +11:00
Damien George 5c320bd0b0 stm32: Introduce MICROPY_HW_ENABLE_USB and clean up USB config.
This patch allows to completely compile-out support for USB, and no-USB is
now the default.  If a board wants to enable USB it should define:

    #define MICROPY_HW_ENABLE_USB (1)

And then one or more of the following to select the USB PHY:

    #define MICROPY_HW_USB_FS (1)
    #define MICROPY_HW_USB_HS (1)
    #define MICROPY_HW_USB_HS_IN_FS (1)
2018-02-13 18:51:08 +11:00
Damien George 8aad22fdca stm32/timer: Support MCUs that don't have TIM4 and/or TIM5. 2018-02-13 15:53:39 +11:00
Damien George 6e91ab5806 stm32/spi: Further updates to use newer versions of HAL names. 2018-02-13 15:53:08 +11:00
Damien George 3eb0694b97 stm32: Update HAL macro and constant names to use newer versions.
Newer versions of the HAL use names which are cleaner and more
self-consistent amongst the HAL itself.  This patch switches to use those
names in most places so it is easier to update the HAL in the future.
2018-02-13 15:37:35 +11:00
Damien George 8e1cb58a23 stm32/usbdev: Fix USBD setup request handler to use correct recipient.
Prior to this patch the USBD driver did not handle the recipient correctly
for setup requests.  It was not interpreting the req->wIndex field in the
right way: in some cases this field indicates the endpoint number but the
code was assuming it always indicated the interface number.

This patch fixes this.  The only noticeable change is to the MSC
interface, which should now correctly respond to the USB_REQ_CLEAR_FEATURE
request and hence unmount properly from the host when requested.
2018-02-12 17:22:59 +11:00
Damien George 02f88cb2df stm32/boards: Remove all config options that are set to defaults.
mpconfigboard_common.h now sets the defaults so there is no longer a need
to explicitly list all configuration options in a board's mpconfigboard.h
file.
2018-02-09 18:40:40 +11:00