114 lines
5.3 KiB
C
114 lines
5.3 KiB
C
#define MICROPY_HW_BOARD_NAME "STM32H573I-DK"
|
|
#define MICROPY_HW_MCU_NAME "STM32H573IIK3Q"
|
|
|
|
#define MICROPY_PY_PYB_LEGACY (0)
|
|
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_ADC (1)
|
|
#define MICROPY_HW_ENABLE_DAC (0) // requires DMA
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
|
|
#if 1
|
|
// The board has a 25MHz oscillator, the following gives 250MHz CPU speed
|
|
#define MICROPY_HW_CLK_USE_BYPASS (1)
|
|
#define MICROPY_HW_CLK_PLLM (5)
|
|
#define MICROPY_HW_CLK_PLLN (100)
|
|
#define MICROPY_HW_CLK_PLLP (2)
|
|
#define MICROPY_HW_CLK_PLLQ (2)
|
|
#define MICROPY_HW_CLK_PLLR (2)
|
|
#define MICROPY_HW_CLK_PLLVCI_LL (LL_RCC_PLLINPUTRANGE_4_8)
|
|
#define MICROPY_HW_CLK_PLLVCO_LL (LL_RCC_PLLVCORANGE_WIDE)
|
|
#define MICROPY_HW_CLK_PLLFRAC (0)
|
|
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_5
|
|
#else
|
|
// Use 64MHz HSI to clock the CPU at 200MHz
|
|
#define MICROPY_HW_CLK_USE_HSI (1) // 64MHz
|
|
#define MICROPY_HW_CLK_PLLM (16)
|
|
#define MICROPY_HW_CLK_PLLN (100)
|
|
#define MICROPY_HW_CLK_PLLP (2)
|
|
#define MICROPY_HW_CLK_PLLQ (2)
|
|
#define MICROPY_HW_CLK_PLLR (2)
|
|
#define MICROPY_HW_CLK_PLLVCI_LL (LL_RCC_PLLINPUTRANGE_4_8)
|
|
#define MICROPY_HW_CLK_PLLVCO_LL (LL_RCC_PLLVCORANGE_WIDE)
|
|
#define MICROPY_HW_CLK_PLLFRAC (0)
|
|
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4 // VOS0, 168-210MHz
|
|
#endif
|
|
|
|
// PLL3 with Q output at 48MHz for USB
|
|
#define MICROPY_HW_CLK_PLL3M (25)
|
|
#define MICROPY_HW_CLK_PLL3N (192)
|
|
#define MICROPY_HW_CLK_PLL3P (2)
|
|
#define MICROPY_HW_CLK_PLL3Q (4)
|
|
#define MICROPY_HW_CLK_PLL3R (2)
|
|
#define MICROPY_HW_CLK_PLL3FRAC (0)
|
|
#define MICROPY_HW_CLK_PLL3VCI_LL (LL_RCC_PLLINPUTRANGE_1_2)
|
|
#define MICROPY_HW_CLK_PLL3VCO_LL (LL_RCC_PLLVCORANGE_MEDIUM)
|
|
|
|
// There is an external 32kHz oscillator
|
|
#define MICROPY_HW_RTC_USE_LSE (1)
|
|
|
|
// 512MBit
|
|
#if !MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE
|
|
#define MICROPY_HW_OSPIFLASH_SIZE_BITS_LOG2 (29)
|
|
#define MICROPY_HW_OSPIFLASH_CS (pin_G6)
|
|
#define MICROPY_HW_OSPIFLASH_SCK (pin_F10)
|
|
#define MICROPY_HW_OSPIFLASH_IO0 (pin_B1)
|
|
#define MICROPY_HW_OSPIFLASH_IO1 (pin_D12)
|
|
#define MICROPY_HW_OSPIFLASH_IO2 (pin_C2)
|
|
#define MICROPY_HW_OSPIFLASH_IO3 (pin_D13)
|
|
#define MICROPY_HW_OSPIFLASH_IO4 (pin_H2)
|
|
#define MICROPY_HW_OSPIFLASH_IO5 (pin_H3)
|
|
#define MICROPY_HW_OSPIFLASH_IO6 (pin_G9)
|
|
#define MICROPY_HW_OSPIFLASH_IO7 (pin_C0)
|
|
#define MICROPY_HW_SPIFLASH_ENABLE_CACHE (1)
|
|
#define MICROPY_HW_BDEV_SPIFLASH (&spi_bdev)
|
|
#define MICROPY_HW_BDEV_SPIFLASH_CONFIG (&spiflash_config)
|
|
#define MICROPY_HW_BDEV_SPIFLASH_SIZE_BYTES ((1 << MICROPY_HW_OSPIFLASH_SIZE_BITS_LOG2) / 8)
|
|
#define MICROPY_HW_BDEV_SPIFLASH_EXTENDED (&spi_bdev) // for extended block protocol
|
|
#endif
|
|
|
|
// UART buses
|
|
#define MICROPY_HW_UART1_TX (pin_A9)
|
|
#define MICROPY_HW_UART1_RX (pin_A10)
|
|
#define MICROPY_HW_UART3_TX (pin_B10) // Arduino Connector CN15-Pin2 (D1)
|
|
#define MICROPY_HW_UART3_RX (pin_B11) // Arduino Connector CN15-Pin1 (D0)
|
|
#define MICROPY_HW_UART_REPL PYB_UART_1
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
|
|
|
// I2C buses
|
|
#define MICROPY_HW_I2C1_SCL (pin_B6) // Arduino Connector CN13-Pin10 (D15)
|
|
#define MICROPY_HW_I2C1_SDA (pin_B7) // Arduino Connector CN13-Pin9 (D14)
|
|
|
|
// SPI buses
|
|
#define MICROPY_HW_SPI2_NSS (pin_A3) // Arduino Connector CN13-Pin3 (D10)
|
|
#define MICROPY_HW_SPI2_SCK (pin_I1) // Arduino Connector CN13-Pin6 (D13)
|
|
#define MICROPY_HW_SPI2_MISO (pin_I2) // Arduino Connector CN13-Pin5 (D12)
|
|
#define MICROPY_HW_SPI2_MOSI (pin_B15) // Arduino Connector CN13-Pin4 (D11)
|
|
|
|
// USRSW is pulled low. Pressing the button makes the input go high.
|
|
#define MICROPY_HW_USRSW_PIN (pin_C13)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_I9) // green
|
|
#define MICROPY_HW_LED2 (pin_I8) // orange
|
|
#define MICROPY_HW_LED3 (pin_F1) // red
|
|
#define MICROPY_HW_LED4 (pin_F4) // blue
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_low(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_high(pin))
|
|
|
|
// USB config
|
|
#define MICROPY_HW_USB_FS (1)
|
|
#define MICROPY_HW_USB_MAIN_DEV (USB_PHY_FS_ID)
|
|
|
|
/******************************************************************************/
|
|
// Variable and function declarations
|
|
|
|
extern const struct _mp_spiflash_config_t spiflash_config;
|
|
extern struct _spi_bdev_t spi_bdev;
|