82b4ab7576
The include of HAL headers should come after the HAL configuration defines, so that the headers can see whether the defines were made or not, to provide defaults and configure various things. Signed-off-by: Damien George <damien@micropython.org> |
||
---|---|---|
.. | ||
README.md | ||
bdev.c | ||
bluetooth_init_cc2564C_1.5.c | ||
board.json | ||
board_init.c | ||
cc2564.c | ||
hub_display.c | ||
hub_display.h | ||
manifest.py | ||
mpconfigboard.h | ||
mpconfigboard.mk | ||
pins.csv | ||
stm32f4xx_hal_conf.h |
README.md
LEGO Hub No.7
This board definition is for the LEGO Hub No. 7, a LEGO control unit with 1 button, 2 RGB LEDs, 2 Powered Up ports, 6-DOF sensor, Bluetooth, USB, 4MiB external SPI flash storage, and a rechargeable battery.
Features that are currently supported:
- standard MicroPython
- machine and bluetooth modules
- filesystem
- USB VCP, MSC and HID
The Hub has a bootloader preinstalled at 0x08000000 (which is 32kiB in size) which cannot be erased. This bootloader is entered by holding down the button for 5 seconds, at which point the USB DFU device appears. If the battery is installed then the RGB LED will flash purple. If the battery is not installed, the LED will flash orange briefly and then the hub will turn off (so having the battery installed is required). When this bootloader is active, the flash from 0x08008000 and up can be erased and programmed via USB DFU.
The built-in bootloader has some drawbacks: it cannot be entered programmatically, and it does not keep the Hub powered up when running from battery (which requires keeping BAT_PWR_EN high). As such, this board is configured to work with mboot as a secondary bootloader: mboot is placed at 0x08008000 and the main application firmware at 0x08010000. When mboot is installed it can be entered programmatically via machine.bootloader().
Backing up original Hub firmware
Before installing MicroPython it is advised to backup the original LEGO firmware that the Hub comes installed with. To do this, enter the built-in bootloader by holding down the power button for 5 seconds while powering up the Hub via USB (you may need to take out the battery and disconnect USB to power off the Hub first). Then run the following command from the root of this repository:
$ cd ports/stm32
$ make BOARD=LEGO_HUB_NO7 backup-hub-firmware
This will create a file called lego_hub_firmware.dfu
. Put this file in a safe
location. To restore it, enter the built-in bootloader again and run:
$ make BOARD=LEGO_HUB_NO7 restore-hub-firmware
This will restore the original firmware but not the filesystem. To recreate the original filesystem the Hub must be updated using the appropriate LEGO PC application.
Installing MicroPython
You first need to build and install mboot, which only needs to be done once. From the root of this repository run:
$ cd ports/stm32/mboot
$ make BOARD=LEGO_HUB_NO7
Now enter the built-in bootloader by holding down the power button for 5 seconds while powering up the Hub via USB (you may need to take out the battery and disconnect USB to power off the Hub first). Then run:
$ make BOARD=LEGO_HUB_NO7 deploy
mboot should now be installed. To enter mboot, remove USB and the battery. Connect the USB cable (the other end of the USB cable must be connected to something that provides power). The status light should start cycling through different colors. Replace the battery (the button will not work without the battery present). Press the button to activate the desired boot mode:
- Status light is red - run application (normal boot).
- Status light is green - run application in factory file system mode.
- Status light is blue - run application in safe mode.
- Status light is white - start DFU on the USB port.
Now build MicroPython (start at the root of this repository):
$ cd mpy-cross
$ make
$ cd ../ports/stm32
$ make submodules
$ make BOARD=LEGO_HUB_NO7
And deploy to the Hub (making sure mboot DFU is active, the center button is blinking red):
$ make BOARD=LEGO_HUB_NO7 deploy
If successful, the Hub should now appear as a USB serial and mass storage device.
Using MicroPython on the Hub
Access the MicroPython REPL using mpremote (pip install mpremote), or with any serial terminal program.
To scan for BLE devices:
>>> import bluetooth
>>> ble = bluetooth.BLE()
>>> ble.irq(lambda *x: print(*x))
>>> ble.active(1)
>>> ble.gap_scan(2000, 625, 625)
Use help("modules") to see available built-in modules.
Updating MicroPython from the Hub's filesystem
You can update the MicroPython application firmware using the instructions above for installing the firmware for the first time. The Hub also supports updating the application firmware from within MicroPython itself, using the on-board filesystem.
To use this feature, build the firmware (see above for details) then gzip it and copy the resulting file to the Hub (eg using mpremote):
$ make BOARD=LEGO_HUB_NO7
$ gzip build-LEGO_HUB_NO7/firmware.dfu
$ mpremote cp build-LEGO_HUB_NO7/firmware.dfu.gz :
Then get a REPL on the Hub and execute:
>>> import appupdate
>>> appupdate.update_app("firmware.dfu.gz")
You can alternatively run this REPL command using mpremote:
$ mpremote exec --no-follow "import appupdate; appupdate.update_app('firmware.dfu.gz')"
At that point the Hub should restart and the LED on the central button will flash different colours. Once the update is complete the LED will stop flashing and the Hub will appear again as a USB device. The application firmware is now updated and you can remove the firmware.dfu.gz file if desired.