87 lines
3.2 KiB
C
87 lines
3.2 KiB
C
#define MICROPY_HW_BOARD_NAME "STM32H7B3I-DK"
|
|
#define MICROPY_HW_MCU_NAME "STM32H7B3LIH6Q"
|
|
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_ADC (1)
|
|
#define MICROPY_HW_ENABLE_DAC (1)
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
#define MICROPY_HW_ENABLE_SDCARD (1)
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_HAS_FLASH (0)
|
|
|
|
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0)
|
|
|
|
// The board has a 24MHz HSE, the following gives 280MHz CPU speed
|
|
#define MICROPY_HW_CLK_PLLM (12)
|
|
#define MICROPY_HW_CLK_PLLN (280)
|
|
#define MICROPY_HW_CLK_PLLP (2)
|
|
#define MICROPY_HW_CLK_PLLQ (2)
|
|
#define MICROPY_HW_CLK_PLLR (2)
|
|
|
|
// The USB clock is set using PLL3 (48Mhz usb clock)
|
|
#define MICROPY_HW_CLK_PLL3M (12)
|
|
#define MICROPY_HW_CLK_PLL3N (192)
|
|
#define MICROPY_HW_CLK_PLL3P (17)
|
|
#define MICROPY_HW_CLK_PLL3Q (8)
|
|
#define MICROPY_HW_CLK_PLL3R (2)
|
|
|
|
// 6 wait states when running at 280MHz (VOS0 range)
|
|
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_6
|
|
|
|
#if 0
|
|
// 512MBit external OSPI flash, used for either the filesystem or XIP memory mapped
|
|
#define MICROPY_HW_OSPIFLASH_SIZE_BITS_LOG2 (29)
|
|
#define MICROPY_HW_OSPIFLASH_CS (pin_G6)
|
|
#define MICROPY_HW_OSPIFLASH_CLK (pin_B2)
|
|
#define MICROPY_HW_OSPIFLASH_DQS (pin_C5)
|
|
#define MICROPY_HW_OSPIFLASH_IO0 (pin_P8)
|
|
#define MICROPY_HW_OSPIFLASH_IO1 (pin_F9)
|
|
#define MICROPY_HW_OSPIFLASH_IO2 (pin_F7)
|
|
#define MICROPY_HW_OSPIFLASH_IO3 (pin_F6)
|
|
#define MICROPY_HW_OSPIFLASH_IO4 (pin_C1)
|
|
#define MICROPY_HW_OSPIFLASH_IO5 (pin_H3)
|
|
#define MICROPY_HW_OSPIFLASH_IO6 (pin_D6)
|
|
#define MICROPY_HW_OSPIFLASH_IO7 (pin_G14)
|
|
#endif
|
|
|
|
// UART buses
|
|
#define MICROPY_HW_UART1_TX (pin_A9)
|
|
#define MICROPY_HW_UART1_RX (pin_A10)
|
|
#define MICROPY_HW_UART4_TX (pin_H13) // Arduino Connector CN11-Pin1
|
|
#define MICROPY_HW_UART4_RX (pin_H14) // Arduino Connector CN11-Pin2
|
|
#define MICROPY_HW_UART_REPL PYB_UART_1
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
|
|
|
// USRSW is pulled low. Pressing the button makes the input go high.
|
|
#define MICROPY_HW_USRSW_PIN (pin_C13)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_G11) // red
|
|
#define MICROPY_HW_LED2 (pin_G2) // blue
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_low(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_high(pin))
|
|
|
|
// USB config
|
|
#define MICROPY_HW_USB_FS (0)
|
|
#define MICROPY_HW_USB_HS (1)
|
|
#define MICROPY_HW_USB_HS_IN_FS (1)
|
|
#define MICROPY_HW_USB_MAIN_DEV (USB_PHY_HS_ID)
|
|
#define MICROPY_HW_USB_CDC_NUM (2)
|
|
#define MICROPY_HW_USB_MSC (0)
|
|
|
|
// SD card detect switch
|
|
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_I8)
|
|
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
|
|
#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET)
|
|
|
|
#define MICROPY_HW_SDMMC_D0 (pin_C8)
|
|
#define MICROPY_HW_SDMMC_D1 (pin_C9)
|
|
#define MICROPY_HW_SDMMC_D2 (pin_C10)
|
|
#define MICROPY_HW_SDMMC_D3 (pin_C11)
|
|
#define MICROPY_HW_SDMMC_CK (pin_C12)
|
|
#define MICROPY_HW_SDMMC_CMD (pin_D2)
|