micropython/cc3200

Build Instructions for the CC3200

Currently the CC3200 port of MicroPython builds under Linux and OSX but not under Windows.

The tool chain required for the build can be found at https://launchpad.net/gcc-arm-embedded.

In order to download the image to the CC3200 you will need the CCS_Uniflash tool from TI, which at this moment is only available for Windows, so, you need Linux/OSX to build and Windows to flash the image.

To build an image suitable for debugging:

In order to debug the port specific code, optimizations need to be disabled on the port file (check the Makefile for specific details). You can use CCS from TI. Use the CC3200.ccxml file supplied with this distribution for the debuuger configuration.

make BTARGET=application BTYPE=debug BOARD=LAUNCHXL

To build an image suitable to be flashed to the device:

make BTARGET=application BTYPE=release BOARD=LAUNCHXL

Building the bootloader

make BTARGET=bootloader BTYPE=release BOARD=LAUNCHXL

Regarding old revisions of the CC3200-LAUNCHXL

First silicon (pre-release) revisions of the CC3200 had issues with the ram blocks, and MicroPython cannot run there. Make sure to use a v4.1 (or higer) LAUNCHXL board when trying this port, otherwise it won't work.

Flashing the CC3200

• Make sure that you have built both the bootloader and the application in release mode.
• Make sure the SOP2 jumper is in position.
• Open CCS_Uniflash and connect to the board (by default on port 22).
• Format the serial flash (select 1MB size in case of the CC3200-LAUNCHXL, 2MB in case of the WiPy, leave the rest unchecked).
• Mark the following files for erasing: /cert/ca.pem, /cert/client.pem, /cert/private.key and /tmp/pac.bin.
• Add a new file with the name of /sys/mcuimg.bin, and select the URL to point to cc3200\bootmgr\build<BOARD_NAME>\bootloader.bin.
• Add another file with the name of /sys/factimg.bin, and select the URL to point to cc3200\build<BOARD_NAME>\mcuimg.bin.
• Click "Program" to apply all changes.
• Flash the latest service pack (servicepack_1.0.0.10.0.bin) using the "Service Pack Update" button.
• Close CCS_Uniflash, remove the SOP2 jumper and reset the board.

Updating the board to with new software version

• Make sure the board is running and connected to the same network as the computer.

make BTARGET=application BTYPE=release BOARD=LAUNCHXL WIPY_IP=192.168.1.1 WIPY_USER=micro WIPY_PWD=python deploy

If WIPY_IP, WIPY_USER or WIPY_PWD are omitted the default values (the ones shown above) will be used.

Playing with MicroPython and the CC3200:

Once the software is running, you have two options to access the MicroPython REPL:

• Through telnet.
  • Connect to the network created by the board (as boots up in AP mode), ssid = "wipy-wlan", key = "www.wipy.io".
    • You can also reinitialize the WLAN in station mode and connect to another AP, or in AP mode but with a different ssid and/or key.
  • Use your favourite telnet client with the following settings: host = 192.168.1.1, port = 23.
  • Log in with user = "micro" and password = "python"

The board has a small file system of 192K (WiPy) or 64K (Launchpad) located in the serial flash connected to the CC3200. SD cards are also supported, you can connect any SD card and configure the pinout using the SD class API.

Uploading scripts:

To upload your MicroPython scripts to the FTP server, open your FTP client of choice and connect to: ftp://192.168.1.1, user = "micro", password = "python"

I have tested the FTP server with FileZilla, FireFTP, FireFox, IE and Chrome, other clients should work as well, but I am not 100% sure of it.

Upgrading the firmware Over The Air:

OTA software updates can be performed through the FTP server. After building a new mcuimg.bin in release mode, upload it to: /flash/sys/mcuimg.bin it will take around 6s (The TI simplelink file system is quite slow because every file is mirrored for safety). You won't see the file being stored inside /flash/sys/ because it's actually saved bypassing FatFS, but rest assured that the file was successfully transferred, and it has been signed with a MD5 checksum to verify its integrity. Now, reset the MCU by pressing the switch on the board, or by typing:

import machine
machine.reset()

Note regarding FileZilla:

Do not use the quick connect button, instead, open the site manager and create a new configuration. In the "General" tab make sure that encryption is set to: "Only use plain FTP (insecure)". In the Transfer Settings tab limit the max number of connections to one, otherwise FileZilla will try to open a second command connection when retrieving and saving files, and for simplicity and to reduce code size, only one command and one data connections are possible.