67 lines
2.2 KiB
C
67 lines
2.2 KiB
C
#include <stm32f4xx.h>
|
|
#include <stm32f4xx_gpio.h>
|
|
#include "led.h"
|
|
|
|
#define PYB_LED_R_PORT (GPIOA)
|
|
#define PYB_LED_R1_PIN (GPIO_Pin_8)
|
|
#define PYB_LED_R2_PIN (GPIO_Pin_10)
|
|
#define PYB_LED_G_PORT (GPIOC)
|
|
#define PYB_LED_G1_PIN (GPIO_Pin_4)
|
|
#define PYB_LED_G2_PIN (GPIO_Pin_5)
|
|
|
|
void led_init(void) {
|
|
// set the output high (so LED is off)
|
|
PYB_LED_R_PORT->BSRRL = PYB_LED_R1_PIN;
|
|
PYB_LED_R_PORT->BSRRL = PYB_LED_R2_PIN;
|
|
PYB_LED_G_PORT->BSRRL = PYB_LED_G1_PIN;
|
|
PYB_LED_G_PORT->BSRRL = PYB_LED_G2_PIN;
|
|
// make them open drain outputs
|
|
GPIO_InitTypeDef GPIO_InitStructure;
|
|
GPIO_InitStructure.GPIO_Pin = PYB_LED_R1_PIN | PYB_LED_R2_PIN;
|
|
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;
|
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
|
|
GPIO_InitStructure.GPIO_OType = GPIO_OType_OD;
|
|
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
|
|
GPIO_Init(PYB_LED_R_PORT, &GPIO_InitStructure);
|
|
GPIO_InitStructure.GPIO_Pin = PYB_LED_G1_PIN | PYB_LED_G2_PIN;
|
|
GPIO_Init(PYB_LED_G_PORT, &GPIO_InitStructure);
|
|
}
|
|
|
|
void led_state(pyb_led_t led, int state) {
|
|
GPIO_TypeDef *port;
|
|
uint32_t pin;
|
|
switch (led) {
|
|
case PYB_LED_R1: port = PYB_LED_R_PORT; pin = PYB_LED_R1_PIN; break;
|
|
case PYB_LED_R2: port = PYB_LED_R_PORT; pin = PYB_LED_R2_PIN; break;
|
|
case PYB_LED_G1: port = PYB_LED_G_PORT; pin = PYB_LED_G1_PIN; break;
|
|
case PYB_LED_G2: port = PYB_LED_G_PORT; pin = PYB_LED_G2_PIN; break;
|
|
default: return;
|
|
}
|
|
if (state == 0) {
|
|
// turn LED off (output is high)
|
|
port->BSRRL = pin;
|
|
} else {
|
|
// turn LED on (output is low)
|
|
port->BSRRH = pin;
|
|
}
|
|
}
|
|
|
|
void led_toggle(pyb_led_t led) {
|
|
GPIO_TypeDef *port;
|
|
uint32_t pin;
|
|
switch (led) {
|
|
case PYB_LED_R1: port = PYB_LED_R_PORT; pin = PYB_LED_R1_PIN; break;
|
|
case PYB_LED_R2: port = PYB_LED_R_PORT; pin = PYB_LED_R2_PIN; break;
|
|
case PYB_LED_G1: port = PYB_LED_G_PORT; pin = PYB_LED_G1_PIN; break;
|
|
case PYB_LED_G2: port = PYB_LED_G_PORT; pin = PYB_LED_G2_PIN; break;
|
|
default: return;
|
|
}
|
|
if (!(port->ODR & pin)) {
|
|
// turn LED off (output high)
|
|
port->BSRRL = pin;
|
|
} else {
|
|
// turn LED on (output low)
|
|
port->BSRRH = pin;
|
|
}
|
|
}
|