353 lines
11 KiB
ReStructuredText
353 lines
11 KiB
ReStructuredText
.. _rp2_quickref:
|
|
|
|
Quick reference for the RP2
|
|
===========================
|
|
|
|
.. image:: img/pico_pinout.png
|
|
:alt: Raspberry Pi Pico
|
|
:width: 640px
|
|
|
|
The Raspberry Pi Pico Development Board (image attribution: Raspberry Pi Foundation).
|
|
|
|
Below is a quick reference for Raspberry Pi RP2xxx boards. If it is your first time
|
|
working with this board it may be useful to get an overview of the microcontroller:
|
|
|
|
.. toctree::
|
|
:maxdepth: 1
|
|
|
|
general.rst
|
|
tutorial/intro.rst
|
|
|
|
Installing MicroPython
|
|
----------------------
|
|
|
|
See the corresponding section of tutorial: :ref:`rp2_intro`. It also includes
|
|
a troubleshooting subsection.
|
|
|
|
General board control
|
|
---------------------
|
|
|
|
The MicroPython REPL is accessed via the USB serial port. Tab-completion is useful to
|
|
find out what methods an object has. Paste mode (ctrl-E) is useful to paste a
|
|
large slab of Python code into the REPL.
|
|
|
|
The :mod:`machine` module::
|
|
|
|
import machine
|
|
|
|
machine.freq() # get the current frequency of the CPU
|
|
machine.freq(240000000) # set the CPU frequency to 240 MHz
|
|
|
|
The :mod:`rp2` module::
|
|
|
|
import rp2
|
|
|
|
Delay and timing
|
|
----------------
|
|
|
|
Use the :mod:`time <time>` module::
|
|
|
|
import time
|
|
|
|
time.sleep(1) # sleep for 1 second
|
|
time.sleep_ms(500) # sleep for 500 milliseconds
|
|
time.sleep_us(10) # sleep for 10 microseconds
|
|
start = time.ticks_ms() # get millisecond counter
|
|
delta = time.ticks_diff(time.ticks_ms(), start) # compute time difference
|
|
|
|
Timers
|
|
------
|
|
|
|
RP2040's system timer peripheral provides a global microsecond timebase and
|
|
generates interrupts for it. The software timer is available currently,
|
|
and there are unlimited number of them (memory permitting). There is no need
|
|
to specify the timer id (id=-1 is supported at the moment) as it will default
|
|
to this.
|
|
|
|
Use the :mod:`machine.Timer` class::
|
|
|
|
from machine import Timer
|
|
|
|
tim = Timer(period=5000, mode=Timer.ONE_SHOT, callback=lambda t:print(1))
|
|
tim.init(period=2000, mode=Timer.PERIODIC, callback=lambda t:print(2))
|
|
|
|
|
|
.. _rp2_Pins_and_GPIO:
|
|
|
|
Pins and GPIO
|
|
-------------
|
|
|
|
Use the :ref:`machine.Pin <machine.Pin>` class::
|
|
|
|
from machine import Pin
|
|
|
|
p0 = Pin(0, Pin.OUT) # create output pin on GPIO0
|
|
p0.on() # set pin to "on" (high) level
|
|
p0.off() # set pin to "off" (low) level
|
|
p0.value(1) # set pin to on/high
|
|
|
|
p2 = Pin(2, Pin.IN) # create input pin on GPIO2
|
|
print(p2.value()) # get value, 0 or 1
|
|
|
|
p4 = Pin(4, Pin.IN, Pin.PULL_UP) # enable internal pull-up resistor
|
|
p5 = Pin(5, Pin.OUT, value=1) # set pin high on creation
|
|
|
|
Programmable IO (PIO)
|
|
---------------------
|
|
|
|
PIO is useful to build low-level IO interfaces from scratch. See the :mod:`rp2` module
|
|
for detailed explaination of the assembly instructions.
|
|
|
|
Example using PIO to blink an LED at 1Hz::
|
|
|
|
from machine import Pin
|
|
import rp2
|
|
|
|
@rp2.asm_pio(set_init=rp2.PIO.OUT_LOW)
|
|
def blink_1hz():
|
|
# Cycles: 1 + 7 + 32 * (30 + 1) = 1000
|
|
set(pins, 1)
|
|
set(x, 31) [6]
|
|
label("delay_high")
|
|
nop() [29]
|
|
jmp(x_dec, "delay_high")
|
|
|
|
# Cycles: 1 + 7 + 32 * (30 + 1) = 1000
|
|
set(pins, 0)
|
|
set(x, 31) [6]
|
|
label("delay_low")
|
|
nop() [29]
|
|
jmp(x_dec, "delay_low")
|
|
|
|
# Create and start a StateMachine with blink_1hz, outputting on Pin(25)
|
|
sm = rp2.StateMachine(0, blink_1hz, freq=2000, set_base=Pin(25))
|
|
sm.active(1)
|
|
|
|
UART (serial bus)
|
|
-----------------
|
|
|
|
There are two UARTs, UART0 and UART1. UART0 can be mapped to GPIO 0/1, 12/13
|
|
and 16/17, and UART1 to GPIO 4/5 and 8/9.
|
|
|
|
|
|
See :ref:`machine.UART <machine.UART>`. ::
|
|
|
|
from machine import UART, Pin
|
|
uart1 = UART(1, baudrate=9600, tx=Pin(4), rx=Pin(5))
|
|
uart1.write('hello') # write 5 bytes
|
|
uart1.read(5) # read up to 5 bytes
|
|
|
|
.. note::
|
|
|
|
REPL over UART is disabled by default. You can see the :ref:`rp2_intro` for
|
|
details on how to enable REPL over UART.
|
|
|
|
|
|
PWM (pulse width modulation)
|
|
----------------------------
|
|
|
|
There are 8 independent channels each of which have 2 outputs making it 16
|
|
PWM channels in total which can be clocked from 7Hz to 125Mhz.
|
|
|
|
Use the ``machine.PWM`` class::
|
|
|
|
from machine import Pin, PWM
|
|
|
|
pwm0 = PWM(Pin(0)) # create PWM object from a pin
|
|
pwm0.freq() # get current frequency
|
|
pwm0.freq(1000) # set frequency
|
|
pwm0.duty_u16() # get current duty cycle, range 0-65535
|
|
pwm0.duty_u16(200) # set duty cycle, range 0-65535
|
|
pwm0.deinit() # turn off PWM on the pin
|
|
|
|
ADC (analog to digital conversion)
|
|
----------------------------------
|
|
|
|
RP2040 has five ADC channels in total, four of which are 12-bit SAR based
|
|
ADCs: GP26, GP27, GP28 and GP29. The input signal for ADC0, ADC1, ADC2 and
|
|
ADC3 can be connected with GP26, GP27, GP28, GP29 respectively (On Pico board,
|
|
GP29 is connected to VSYS). The standard ADC range is 0-3.3V. The fifth
|
|
channel is connected to the in-built temperature sensor and can be used for
|
|
measuring the temperature.
|
|
|
|
Use the :ref:`machine.ADC <machine.ADC>` class::
|
|
|
|
from machine import ADC, Pin
|
|
adc = ADC(Pin(26)) # create ADC object on ADC pin
|
|
adc.read_u16() # read value, 0-65535 across voltage range 0.0v - 3.3v
|
|
|
|
Software SPI bus
|
|
----------------
|
|
|
|
Software SPI (using bit-banging) works on all pins, and is accessed via the
|
|
:ref:`machine.SoftSPI <machine.SoftSPI>` class::
|
|
|
|
from machine import Pin, SoftSPI
|
|
|
|
# construct a SoftSPI bus on the given pins
|
|
# polarity is the idle state of SCK
|
|
# phase=0 means sample on the first edge of SCK, phase=1 means the second
|
|
spi = SoftSPI(baudrate=100_000, polarity=1, phase=0, sck=Pin(0), mosi=Pin(2), miso=Pin(4))
|
|
|
|
spi.init(baudrate=200000) # set the baudrate
|
|
|
|
spi.read(10) # read 10 bytes on MISO
|
|
spi.read(10, 0xff) # read 10 bytes while outputting 0xff on MOSI
|
|
|
|
buf = bytearray(50) # create a buffer
|
|
spi.readinto(buf) # read into the given buffer (reads 50 bytes in this case)
|
|
spi.readinto(buf, 0xff) # read into the given buffer and output 0xff on MOSI
|
|
|
|
spi.write(b'12345') # write 5 bytes on MOSI
|
|
|
|
buf = bytearray(4) # create a buffer
|
|
spi.write_readinto(b'1234', buf) # write to MOSI and read from MISO into the buffer
|
|
spi.write_readinto(buf, buf) # write buf to MOSI and read MISO back into buf
|
|
|
|
.. Warning::
|
|
Currently *all* of ``sck``, ``mosi`` and ``miso`` *must* be specified when
|
|
initialising Software SPI.
|
|
|
|
Hardware SPI bus
|
|
----------------
|
|
|
|
The RP2040 has 2 hardware SPI buses which is accessed via the
|
|
:ref:`machine.SPI <machine.SPI>` class and has the same methods as software
|
|
SPI above::
|
|
|
|
from machine import Pin, SPI
|
|
|
|
spi = SPI(1, 10_000_000) # Default assignment: sck=Pin(10), mosi=Pin(11), miso=Pin(8)
|
|
spi = SPI(1, 10_000_000, sck=Pin(14), mosi=Pin(15), miso=Pin(12))
|
|
spi = SPI(0, baudrate=80_000_000, polarity=0, phase=0, bits=8, sck=Pin(6), mosi=Pin(7), miso=Pin(4))
|
|
|
|
Software I2C bus
|
|
----------------
|
|
|
|
Software I2C (using bit-banging) works on all output-capable pins, and is
|
|
accessed via the :ref:`machine.SoftI2C <machine.SoftI2C>` class::
|
|
|
|
from machine import Pin, SoftI2C
|
|
|
|
i2c = SoftI2C(scl=Pin(5), sda=Pin(4), freq=100_000)
|
|
|
|
i2c.scan() # scan for devices
|
|
|
|
i2c.readfrom(0x3a, 4) # read 4 bytes from device with address 0x3a
|
|
i2c.writeto(0x3a, '12') # write '12' to device with address 0x3a
|
|
|
|
buf = bytearray(10) # create a buffer with 10 bytes
|
|
i2c.writeto(0x3a, buf) # write the given buffer to the peripheral
|
|
|
|
Hardware I2C bus
|
|
----------------
|
|
|
|
The driver is accessed via the :ref:`machine.I2C <machine.I2C>` class and
|
|
has the same methods as software I2C above::
|
|
|
|
from machine import Pin, I2C
|
|
|
|
i2c = I2C(0) # default assignment: scl=Pin(9), sda=Pin(8)
|
|
i2c = I2C(1, scl=Pin(3), sda=Pin(2), freq=400_000)
|
|
|
|
I2S bus
|
|
-------
|
|
|
|
See :ref:`machine.I2S <machine.I2S>`. ::
|
|
|
|
from machine import I2S, Pin
|
|
|
|
i2s = I2S(0, sck=Pin(16), ws=Pin(17), sd=Pin(18), mode=I2S.TX, bits=16, format=I2S.STEREO, rate=44100, ibuf=40000) # create I2S object
|
|
i2s.write(buf) # write buffer of audio samples to I2S device
|
|
|
|
i2s = I2S(1, sck=Pin(0), ws=Pin(1), sd=Pin(2), mode=I2S.RX, bits=16, format=I2S.MONO, rate=22050, ibuf=40000) # create I2S object
|
|
i2s.readinto(buf) # fill buffer with audio samples from I2S device
|
|
|
|
The ``ws`` pin number must be one greater than the ``sck`` pin number.
|
|
|
|
The I2S class is currently available as a Technical Preview. During the preview period, feedback from
|
|
users is encouraged. Based on this feedback, the I2S class API and implementation may be changed.
|
|
|
|
Two I2S buses are supported with id=0 and id=1.
|
|
|
|
Real time clock (RTC)
|
|
---------------------
|
|
|
|
See :ref:`machine.RTC <machine.RTC>` ::
|
|
|
|
from machine import RTC
|
|
|
|
rtc = RTC()
|
|
rtc.datetime((2017, 8, 23, 2, 12, 48, 0, 0)) # set a specific date and
|
|
# time, eg. 2017/8/23 1:12:48
|
|
rtc.datetime() # get date and time
|
|
|
|
WDT (Watchdog timer)
|
|
--------------------
|
|
|
|
The RP2040 has a watchdog which is a countdown timer that can restart
|
|
parts of the chip if it reaches zero.
|
|
|
|
See :ref:`machine.WDT <machine.WDT>`. ::
|
|
|
|
from machine import WDT
|
|
|
|
# enable the WDT with a timeout of 5s (1s is the minimum)
|
|
wdt = WDT(timeout=5000)
|
|
wdt.feed()
|
|
|
|
The maximum value for timeout is 8388 ms.
|
|
|
|
OneWire driver
|
|
--------------
|
|
|
|
The OneWire driver is implemented in software and works on all pins::
|
|
|
|
from machine import Pin
|
|
import onewire
|
|
|
|
ow = onewire.OneWire(Pin(12)) # create a OneWire bus on GPIO12
|
|
ow.scan() # return a list of devices on the bus
|
|
ow.reset() # reset the bus
|
|
ow.readbyte() # read a byte
|
|
ow.writebyte(0x12) # write a byte on the bus
|
|
ow.write('123') # write bytes on the bus
|
|
ow.select_rom(b'12345678') # select a specific device by its ROM code
|
|
|
|
There is a specific driver for DS18S20 and DS18B20 devices::
|
|
|
|
import time, ds18x20
|
|
ds = ds18x20.DS18X20(ow)
|
|
roms = ds.scan()
|
|
ds.convert_temp()
|
|
time.sleep_ms(750)
|
|
for rom in roms:
|
|
print(ds.read_temp(rom))
|
|
|
|
Be sure to put a 4.7k pull-up resistor on the data line. Note that
|
|
the ``convert_temp()`` method must be called each time you want to
|
|
sample the temperature.
|
|
|
|
NeoPixel and APA106 driver
|
|
--------------------------
|
|
|
|
Use the ``neopixel`` and ``apa106`` modules::
|
|
|
|
from machine import Pin
|
|
from neopixel import NeoPixel
|
|
|
|
pin = Pin(0, Pin.OUT) # set GPIO0 to output to drive NeoPixels
|
|
np = NeoPixel(pin, 8) # create NeoPixel driver on GPIO0 for 8 pixels
|
|
np[0] = (255, 255, 255) # set the first pixel to white
|
|
np.write() # write data to all pixels
|
|
r, g, b = np[0] # get first pixel colour
|
|
|
|
|
|
The APA106 driver extends NeoPixel, but internally uses a different colour order::
|
|
|
|
from apa106 import APA106
|
|
ap = APA106(pin, 8)
|
|
r, g, b = ap[0]
|
|
|
|
APA102 (DotStar) uses a different driver as it has an additional clock pin.
|