micropython/stm/stmperiph/stm324x7i_eval.h

118 lines
4.6 KiB
C

/**
******************************************************************************
* @file STM324x7i_eval.h
* @author MCD Application Team
* @version V1.0.0
* @date 11-January-2013
* @brief This file contains definitions for STM324x7I_EVAL's Leds, push-buttons
* and COM ports hardware resources.
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT 2013 STMicroelectronics</center></h2>
*
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/software_license_agreement_liberty_v2
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM324x7I_EVAL_H
#define __STM324x7I_EVAL_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx.h"
#include "mpconfig.h"
/**
* @brief SD FLASH SDIO Interface
*/
#if defined(PYBOARD3)
#define SD_DETECT_PIN GPIO_Pin_13 /* PC.13 */
#define SD_DETECT_GPIO_PORT GPIOC /* GPIOC */
#define SD_DETECT_GPIO_CLK RCC_AHB1Periph_GPIOC
#elif defined(PYBOARD4)
#define SD_DETECT_PIN GPIO_Pin_8 /* PA..8 */
#define SD_DETECT_GPIO_PORT GPIOA /* GPIOA */
#define SD_DETECT_GPIO_CLK RCC_AHB1Periph_GPIOA
#elif defined(STM32F4DISC)
// PB15 on the DM-STSTF4BB Base Board
#define SD_DETECT_PIN GPIO_Pin_15 /* PB.15 */
#define SD_DETECT_GPIO_PORT GPIOB /* GPIOB */
#define SD_DETECT_GPIO_CLK RCC_AHB1Periph_GPIOB
#elif defined(NETDUINO_PLUS_2)
#define SD_DETECT_PIN GPIO_Pin_5 /* PB.5 */
#define SD_DETECT_GPIO_PORT GPIOB /* GPIOB */
#define SD_DETECT_GPIO_CLK RCC_AHB1Periph_GPIOB
#endif
#define SDIO_FIFO_ADDRESS ((uint32_t)0x40012C80)
/**
* @brief SDIO Intialization Frequency (400KHz max)
*/
#define SDIO_INIT_CLK_DIV ((uint8_t)0x76)
/**
* @brief SDIO Data Transfer Frequency (25MHz max)
*/
#define SDIO_TRANSFER_CLK_DIV ((uint8_t)0x0)
#define SD_SDIO_DMA DMA2
#define SD_SDIO_DMA_CLK RCC_AHB1Periph_DMA2
#define SD_SDIO_DMA_STREAM3 3
//#define SD_SDIO_DMA_STREAM6 6
#ifdef SD_SDIO_DMA_STREAM3
#define SD_SDIO_DMA_STREAM DMA2_Stream3
#define SD_SDIO_DMA_CHANNEL DMA_Channel_4
#define SD_SDIO_DMA_FLAG_FEIF DMA_FLAG_FEIF3
#define SD_SDIO_DMA_FLAG_DMEIF DMA_FLAG_DMEIF3
#define SD_SDIO_DMA_FLAG_TEIF DMA_FLAG_TEIF3
#define SD_SDIO_DMA_FLAG_HTIF DMA_FLAG_HTIF3
#define SD_SDIO_DMA_FLAG_TCIF DMA_FLAG_TCIF3
#define SD_SDIO_DMA_IRQn DMA2_Stream3_IRQn
#define SD_SDIO_DMA_IRQHANDLER DMA2_Stream3_IRQHandler
#elif defined SD_SDIO_DMA_STREAM6
#define SD_SDIO_DMA_STREAM DMA2_Stream6
#define SD_SDIO_DMA_CHANNEL DMA_Channel_4
#define SD_SDIO_DMA_FLAG_FEIF DMA_FLAG_FEIF6
#define SD_SDIO_DMA_FLAG_DMEIF DMA_FLAG_DMEIF6
#define SD_SDIO_DMA_FLAG_TEIF DMA_FLAG_TEIF6
#define SD_SDIO_DMA_FLAG_HTIF DMA_FLAG_HTIF6
#define SD_SDIO_DMA_FLAG_TCIF DMA_FLAG_TCIF6
#define SD_SDIO_DMA_IRQn DMA2_Stream6_IRQn
#define SD_SDIO_DMA_IRQHANDLER DMA2_Stream6_IRQHandler
#endif /* SD_SDIO_DMA_STREAM3 */
/** @defgroup STM324x7I_EVAL_LOW_LEVEL_Exported_Functions
* @{
*/
void SD_LowLevel_DeInit(void);
void SD_LowLevel_Init_Detect(void);
void SD_LowLevel_Init(void);
void SD_LowLevel_DMA_TxConfig(uint32_t *BufferSRC, uint32_t BufferSize);
void SD_LowLevel_DMA_RxConfig(uint32_t *BufferDST, uint32_t BufferSize);
#ifdef __cplusplus
}
#endif
#endif /* __STM324x7I_EVAL_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/