87 lines
3.0 KiB
C
87 lines
3.0 KiB
C
#define MICROPY_HW_BOARD_NAME "Adafruit Feather STM32F405"
|
|
#define MICROPY_HW_MCU_NAME "STM32F405RG"
|
|
|
|
#define MICROPY_HW_HAS_SWITCH (0)
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
#define MICROPY_HW_HAS_MMA7660 (0)
|
|
#define MICROPY_HW_HAS_LCD (0)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_SERVO (1)
|
|
#define MICROPY_HW_ENABLE_DAC (1)
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
#define MICROPY_HW_ENABLE_SDCARD (1)
|
|
|
|
// HSE is 12MHz
|
|
#define MICROPY_HW_CLK_PLLM (12)
|
|
#define MICROPY_HW_CLK_PLLN (336)
|
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
|
|
#define MICROPY_HW_CLK_PLLQ (7)
|
|
#define MICROPY_HW_CLK_LAST_FREQ (1)
|
|
|
|
// The Feather has a 32kHz crystal for the RTC
|
|
#define MICROPY_HW_RTC_USE_LSE (1)
|
|
#define MICROPY_HW_RTC_USE_US (0)
|
|
#define MICROPY_HW_RTC_USE_CALOUT (1)
|
|
|
|
// UART config
|
|
#define MICROPY_HW_UART3_NAME "UART3" // on RX / TX
|
|
#define MICROPY_HW_UART3_TX (pin_B10) // TX
|
|
#define MICROPY_HW_UART3_RX (pin_B11) // RX
|
|
#define MICROPY_HW_UART3_RTS (pin_B14) // MISO
|
|
#define MICROPY_HW_UART3_CTS (pin_B13) // SCK
|
|
|
|
#define MICROPY_HW_UART2_NAME "UART2" // on SDA/SCL
|
|
#define MICROPY_HW_UART2_TX (pin_B6) // SCL
|
|
#define MICROPY_HW_UART2_RX (pin_B7) // SDA
|
|
|
|
#define MICROPY_HW_UART6_NAME "UART6" // on D5/D6
|
|
#define MICROPY_HW_UART6_TX (pin_C6) // D6
|
|
#define MICROPY_HW_UART6_RX (pin_C7) // D5
|
|
|
|
// I2C buses
|
|
#define MICROPY_HW_I2C1_NAME "I2C1"
|
|
#define MICROPY_HW_I2C1_SCL (pin_B6) // SCL
|
|
#define MICROPY_HW_I2C1_SDA (pin_B7) // SDA
|
|
#define MICROPY_HW_I2C2_NAME "I2C2"
|
|
#define MICROPY_HW_I2C2_SCL (pin_B10) // TX
|
|
#define MICROPY_HW_I2C2_SDA (pin_B11) // RX
|
|
|
|
// SPI buses
|
|
#define MICROPY_HW_SPI1_NAME "SPIFLASH"
|
|
#define MICROPY_HW_SPI1_NSS (pin_A15) // FLASH CS
|
|
#define MICROPY_HW_SPI1_SCK (pin_B3) // FLASH CLK
|
|
#define MICROPY_HW_SPI1_MISO (pin_B4) // FLASH MISO
|
|
#define MICROPY_HW_SPI1_MOSI (pin_B5) // FLASH MOSI
|
|
#define MICROPY_HW_SPI2_NAME "SPI1"
|
|
#define MICROPY_HW_SPI2_NSS (pin_B12) // SD DETECT
|
|
#define MICROPY_HW_SPI2_SCK (pin_B13) // SCK
|
|
#define MICROPY_HW_SPI2_MISO (pin_B14) // MISO
|
|
#define MICROPY_HW_SPI2_MOSI (pin_B15) // MOSI
|
|
|
|
// CAN buses
|
|
#define MICROPY_HW_CAN1_NAME "CAN1"
|
|
#define MICROPY_HW_CAN1_TX (pin_B9) // D10
|
|
#define MICROPY_HW_CAN1_RX (pin_B8) // D9
|
|
|
|
// The Feather has 1 LED
|
|
#define MICROPY_HW_LED1 (pin_C1) // red
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
|
|
|
// SD card detect switch
|
|
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_B12)
|
|
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
|
|
#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET)
|
|
|
|
// USB config
|
|
#define MICROPY_HW_USB_FS (1)
|
|
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
|
|
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
|
|
|
|
// Bootloader configuration (only needed if Mboot is used)
|
|
#define MBOOT_I2C_PERIPH_ID 1
|
|
#define MBOOT_I2C_SCL (pin_B8)
|
|
#define MBOOT_I2C_SDA (pin_B9)
|
|
#define MBOOT_I2C_ALTFUNC (4)
|