74 lines
2.5 KiB
C
74 lines
2.5 KiB
C
#define MICROPY_HW_BOARD_NAME "B-L475E-IOT01A"
|
|
#define MICROPY_HW_MCU_NAME "STM32L475"
|
|
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
|
|
// MSI is used and is 4MHz
|
|
#define MICROPY_HW_CLK_PLLM (1)
|
|
#define MICROPY_HW_CLK_PLLN (40)
|
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV7)
|
|
#define MICROPY_HW_CLK_PLLR (RCC_PLLR_DIV2)
|
|
#define MICROPY_HW_CLK_PLLQ (RCC_PLLQ_DIV4)
|
|
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4
|
|
|
|
// The board has an external 32kHz crystal
|
|
#define MICROPY_HW_RTC_USE_LSE (1)
|
|
|
|
// USART1 config connected to ST-Link
|
|
#define MICROPY_HW_UART1_TX (pin_B6)
|
|
#define MICROPY_HW_UART1_RX (pin_B7)
|
|
// USART2 config connected to PMOD: Flow control is defined and therefore used
|
|
#define MICROPY_HW_UART2_CTS (pin_D3)
|
|
#define MICROPY_HW_UART2_RTS (pin_D4)
|
|
#define MICROPY_HW_UART2_TX (pin_D5)
|
|
#define MICROPY_HW_UART2_RX (pin_D6)
|
|
// USART3 config for internal use
|
|
#define MICROPY_HW_UART3_TX (pin_D8)
|
|
#define MICROPY_HW_UART3_RX (pin_D9)
|
|
// USART4 config
|
|
#define MICROPY_HW_UART4_TX (pin_A0)
|
|
#define MICROPY_HW_UART4_RX (pin_A1)
|
|
// USART 1 is connected to the virtual com port on the ST-LINK
|
|
#define MICROPY_HW_UART_REPL PYB_UART_1
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
|
|
|
// I2C buses
|
|
#define MICROPY_HW_I2C1_SCL (pin_B8)
|
|
#define MICROPY_HW_I2C1_SDA (pin_B9)
|
|
#define MICROPY_HW_I2C2_SCL (pin_B10)
|
|
#define MICROPY_HW_I2C2_SDA (pin_B11)
|
|
|
|
// SPI buses
|
|
#define MICROPY_HW_SPI1_NSS (pin_A4)
|
|
#define MICROPY_HW_SPI1_SCK (pin_A5)
|
|
#define MICROPY_HW_SPI1_MISO (pin_A6)
|
|
#define MICROPY_HW_SPI1_MOSI (pin_A7)
|
|
|
|
#define MICROPY_HW_SPI2_NSS (pin_D0)
|
|
#define MICROPY_HW_SPI2_SCK (pin_D1)
|
|
#define MICROPY_HW_SPI2_MISO (pin_D3)
|
|
#define MICROPY_HW_SPI2_MOSI (pin_D4)
|
|
|
|
#define MICROPY_HW_SPI3_NSS (pin_A15)
|
|
#define MICROPY_HW_SPI3_SCK (pin_C10)
|
|
#define MICROPY_HW_SPI3_MISO (pin_C11)
|
|
#define MICROPY_HW_SPI3_MOSI (pin_C12)
|
|
|
|
// User and wake-up switch. Pressing the button makes the input go low.
|
|
#define MICROPY_HW_USRSW_PIN (pin_C13)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
|
|
#define MICROPY_HW_USRSW_PRESSED (0)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_A5) // green
|
|
#define MICROPY_HW_LED2 (pin_B14) // green
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
|
|
|
// USB config
|
|
#define MICROPY_HW_USB_FS (1)
|