71 lines
3.1 KiB
C
71 lines
3.1 KiB
C
// MCU config
|
|
#define MICROPY_HW_BOARD_NAME "RA4M1_EK"
|
|
#define MICROPY_HW_MCU_NAME "RA4M1"
|
|
#define MICROPY_HW_MCU_SYSCLK 48000000
|
|
#define MICROPY_HW_MCU_PCLK 48000000
|
|
|
|
// module config
|
|
#define MICROPY_EMIT_THUMB (0)
|
|
#define MICROPY_EMIT_INLINE_THUMB (0)
|
|
#define MICROPY_PY_BUILTINS_COMPLEX (0)
|
|
#define MICROPY_PY_GENERATOR_PEND_THROW (0)
|
|
#define MICROPY_PY_MATH (0)
|
|
#define MICROPY_PY_UHEAPQ (0)
|
|
#define MICROPY_PY_UTIMEQ (0)
|
|
#define MICROPY_PY_THREAD (0)
|
|
|
|
// peripheral config
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_RTC_SOURCE (0) // 0: subclock, 1:LOCO
|
|
#define MICROPY_HW_ENABLE_ADC (1)
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (1)
|
|
|
|
// board config
|
|
|
|
// UART
|
|
#define MICROPY_HW_UART0_TX (pin_P411) // REPL
|
|
#define MICROPY_HW_UART0_RX (pin_P410) // REPL
|
|
#define MICROPY_HW_UART1_TX (pin_P401) // PMOD B
|
|
#define MICROPY_HW_UART1_RX (pin_P402) // PMOD B
|
|
#define MICROPY_HW_UART1_CTS (pin_P403) // PMOD B
|
|
#define MICROPY_HW_UART2_TX (pin_P302)
|
|
#define MICROPY_HW_UART2_RX (pin_P301)
|
|
#define MICROPY_HW_UART2_CTS (pin_P203) // (Conflict with SPI1)
|
|
// #define MICROPY_HW_UART9_TX (pin_P602) // Disable (vector not registered)
|
|
// #define MICROPY_HW_UART9_RX (pin_P601) // Disable (vector not registered)
|
|
// #define MICROPY_HW_UART9_CTS (pin_P603) // Disable (vector not registered)
|
|
#define MICROPY_HW_UART_REPL HW_UART_0
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
|
|
|
// I2C (not supported)
|
|
// #define MICROPY_HW_I2C0_SCL (pin_P204) // Conflict with SPI1
|
|
// #define MICROPY_HW_I2C0_SDA (pin_P407) // Conflict with USB_VBUS
|
|
// #define MICROPY_HW_I2C0_SCL (pin_P400) // Conflict wiht PMOD B (GPIO)
|
|
// #define MICROPY_HW_I2C0_SDA (pin_P401) // Conflict with PMOD B (TXD1)
|
|
// #define MICROPY_HW_I2C1_SCL (pin_P100) // Conflict with PMOD A (MISOA_A)
|
|
// #define MICROPY_HW_I2C1_SDA (pin_P101) // Conflict with PMOD A (MOSIA_A)
|
|
|
|
// SPI
|
|
#define MICROPY_HW_SPI0_SSL (pin_P103) // PMOD A
|
|
#define MICROPY_HW_SPI0_RSPCK (pin_P102) // PMOD A
|
|
#define MICROPY_HW_SPI0_MISO (pin_P100) // PMOD A
|
|
#define MICROPY_HW_SPI0_MOSI (pin_P101) // PMOD A
|
|
#define MICROPY_HW_SPI1_SSL (pin_P206) // Use SSLB1 due to SSLB0 is used for TSCAP
|
|
// #define MICROPY_HW_SPI1_RSPCK (pin_P204) // Disable (vector not registered)
|
|
// #define MICROPY_HW_SPI1_MISO (pin_P202) // Disable (vector not registered)
|
|
// #define MICROPY_HW_SPI1_MOSI (pin_P203) // Disable (vector not registered)
|
|
|
|
// Switch
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_USRSW_PIN (pin_P105)
|
|
#define MICROPY_HW_USRSW_PULL (MP_HAL_PIN_PULL_NONE)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (MP_HAL_PIN_TRIGGER_FALLING)
|
|
#define MICROPY_HW_USRSW_PRESSED (0)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_P106)
|
|
#define MICROPY_HW_LED_ON(pin) mp_hal_pin_high(pin)
|
|
#define MICROPY_HW_LED_OFF(pin) mp_hal_pin_low(pin)
|
|
#define MICROPY_HW_LED_TOGGLE(pin) mp_hal_pin_toggle(pin)
|