76 lines
3.3 KiB
C
76 lines
3.3 KiB
C
// MCU config
|
|
#define MICROPY_HW_BOARD_NAME "RA6M1_EK"
|
|
#define MICROPY_HW_MCU_NAME "RA6M1"
|
|
#define MICROPY_HW_MCU_SYSCLK 120000000
|
|
#define MICROPY_HW_MCU_PCLK 60000000
|
|
|
|
// module config
|
|
#define MICROPY_EMIT_THUMB (1)
|
|
#define MICROPY_EMIT_INLINE_THUMB (1)
|
|
#define MICROPY_PY_BUILTINS_COMPLEX (1)
|
|
#define MICROPY_PY_GENERATOR_PEND_THROW (1)
|
|
#define MICROPY_PY_MATH (1)
|
|
#define MICROPY_PY_UHEAPQ (1)
|
|
#define MICROPY_PY_UTIMEQ (1)
|
|
#define MICROPY_PY_THREAD (0) // disable ARM_THUMB_FP using vldr due to RA has single float only
|
|
|
|
// peripheral config
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_RTC_SOURCE (0) // subclock
|
|
#define MICROPY_HW_ENABLE_ADC (1)
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (1)
|
|
|
|
// board config
|
|
|
|
// UART
|
|
#define MICROPY_HW_UART0_TX (pin_P411) // REPL
|
|
#define MICROPY_HW_UART0_RX (pin_P410) // REPL
|
|
// #define MICROPY_HW_UART1_TX (pin_P213) // Disable (Conflict with XTAL)
|
|
// #define MICROPY_HW_UART1_RX (pin_P212) // Disable (Conflict with XTAL)
|
|
#define MICROPY_HW_UART2_TX (pin_P302)
|
|
#define MICROPY_HW_UART2_RX (pin_P301)
|
|
// #define MICROPY_HW_UART3_TX (pin_P409) // Disable
|
|
// #define MICROPY_HW_UART3_RX (pin_P408) // Disable
|
|
// #define MICROPY_HW_UART3_CTS (pin_P411) // Disable (Conflict with UART0_TX)
|
|
// #define MICROPY_HW_UART4_TX (pin_P205) // Disable (Conflict with TSCAP-A)
|
|
// #define MICROPY_HW_UART4_RX (pin_P206) // Disable
|
|
// #define MICROPY_HW_UART4_CTS (pin_P401) // Disable
|
|
#define MICROPY_HW_UART8_TX (pin_P105) // PMOD B
|
|
#define MICROPY_HW_UART8_RX (pin_P104) // PMOD B
|
|
#define MICROPY_HW_UART8_CTS (pin_P107) // PMOD B
|
|
// #define MICROPY_HW_UART9_TX (pin_P602) // Disable (does not work properly)
|
|
// #define MICROPY_HW_UART9_RX (pin_P601) // Disable (does not work properly)
|
|
// #define MICROPY_HW_UART9_CTS (pin_P301) // Disable (does not work properly)
|
|
#define MICROPY_HW_UART_REPL HW_UART_0
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
|
|
|
// I2C
|
|
#define MICROPY_HW_I2C0_SCL (pin_P400)
|
|
#define MICROPY_HW_I2C0_SDA (pin_P401)
|
|
// #define MICROPY_HW_I2C1_SCL (pin_P100) // Disable (Conflict with SPI0)
|
|
// #define MICROPY_HW_I2C1_SDA (pin_P101) // Disable (Conflict with SPI0)
|
|
|
|
// SPI
|
|
#define MICROPY_HW_SPI0_SSL (pin_P103) // PMOD A
|
|
#define MICROPY_HW_SPI0_RSPCK (pin_P102) // PMOD A
|
|
#define MICROPY_HW_SPI0_MISO (pin_P100) // PMOD A
|
|
#define MICROPY_HW_SPI0_MOSI (pin_P101) // PMOD A
|
|
// #define MICROPY_HW_SPI1_SSL (pin_P108) // Disable (Used for J-Link)
|
|
// #define MICROPY_HW_SPI1_RSPCK (pin_P111)
|
|
// #define MICROPY_HW_SPI1_MISO (pin_P110)
|
|
// #define MICROPY_HW_SPI1_MOSI (pin_P109)
|
|
|
|
// Switch
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_USRSW_PIN (pin_P415)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
|
|
#define MICROPY_HW_USRSW_PRESSED (0)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_P112)
|
|
#define MICROPY_HW_LED_ON(pin) mp_hal_pin_high(pin)
|
|
#define MICROPY_HW_LED_OFF(pin) mp_hal_pin_low(pin)
|
|
#define MICROPY_HW_LED_TOGGLE(pin) mp_hal_pin_toggle(pin)
|