micropython/stmhal/boards/NUCLEO_L476RG/mpconfigboard.h

58 lines
1.9 KiB
C

#define MICROPY_HW_BOARD_NAME "NUCLEO-L476RG"
#define MICROPY_HW_MCU_NAME "STM32L476RG"
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_HAS_SDCARD (0)
#define MICROPY_HW_HAS_LCD (0)
#define MICROPY_HW_ENABLE_RTC (1)
// MSI is used and is 4MHz
#define MICROPY_HW_CLK_PLLM (1)
#define MICROPY_HW_CLK_PLLN (40)
#define MICROPY_HW_CLK_PLLR (2)
#define MICROPY_HW_CLK_PLLP (7)
#define MICROPY_HW_CLK_PLLQ (4)
// UART config
#define MICROPY_HW_UART2_TX (pin_A2)
#define MICROPY_HW_UART2_RX (pin_A3)
#define MICROPY_HW_UART_REPL PYB_UART_2
#define MICROPY_HW_UART_REPL_BAUD 115200
#define MICROPY_HW_I2C_BAUDRATE_TIMING {{100000, 0x90112626}}
#define MICROPY_HW_I2C_BAUDRATE_DEFAULT 100000
#define MICROPY_HW_I2C_BAUDRATE_MAX 100000
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4
// I2C busses
#define MICROPY_HW_I2C1_SCL (pin_B6)
#define MICROPY_HW_I2C1_SDA (pin_B7)
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)
#define MICROPY_HW_I2C3_SCL (pin_C0)
#define MICROPY_HW_I2C3_SDA (pin_C1)
// SPI busses
#define MICROPY_HW_SPI1_NSS (pin_A4)
#define MICROPY_HW_SPI1_SCK (pin_B3)
#define MICROPY_HW_SPI1_MISO (pin_B4)
#define MICROPY_HW_SPI1_MOSI (pin_B5)
#define MICROPY_HW_SPI2_NSS (pin_B12)
#define MICROPY_HW_SPI2_SCK (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
// USRSW is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN (pin_C13)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
#define MICROPY_HW_USRSW_PRESSED (0)
// LEDs
#define MICROPY_HW_LED1 (pin_A5) // Green LD2 LED on Nucleo
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))