271 lines
7.5 KiB
C
271 lines
7.5 KiB
C
/**
|
|
******************************************************************************
|
|
* @file usb_bsp.c
|
|
* @author MCD Application Team
|
|
* @version V1.1.0
|
|
* @date 19-March-2012
|
|
* @brief This file is responsible to offer board support package and is
|
|
* configurable by user.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© COPYRIGHT 2012 STMicroelectronics</center></h2>
|
|
*
|
|
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
|
|
* You may not use this file except in compliance with the License.
|
|
* You may obtain a copy of the License at:
|
|
*
|
|
* http://www.st.com/software_license_agreement_liberty_v2
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS,
|
|
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
* See the License for the specific language governing permissions and
|
|
* limitations under the License.
|
|
*
|
|
******************************************************************************
|
|
*/
|
|
|
|
/* Includes ------------------------------------------------------------------*/
|
|
#include "stm_misc.h"
|
|
#include "stm32f4xx_gpio.h"
|
|
#include "stm32f4xx_rcc.h"
|
|
#include "usb_bsp.h"
|
|
|
|
/** @addtogroup STM32_USB_OTG_DEVICE_LIBRARY
|
|
* @{
|
|
*/
|
|
|
|
/** @defgroup USB_BSP
|
|
* @brief This file is responsible to offer board support package
|
|
* @{
|
|
*/
|
|
|
|
/** @defgroup USB_BSP_Private_Defines
|
|
* @{
|
|
*/
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
|
|
/** @defgroup USB_BSP_Private_TypesDefinitions
|
|
* @{
|
|
*/
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
|
|
|
|
|
|
|
|
/** @defgroup USB_BSP_Private_Macros
|
|
* @{
|
|
*/
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup USBH_BSP_Private_Variables
|
|
* @{
|
|
*/
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup USBH_BSP_Private_FunctionPrototypes
|
|
* @{
|
|
*/
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup USB_BSP_Private_Functions
|
|
* @{
|
|
*/
|
|
|
|
|
|
/**
|
|
* @brief USB_OTG_BSP_Init
|
|
* Initilizes BSP configurations
|
|
* @param None
|
|
* @retval None
|
|
*/
|
|
|
|
void USB_OTG_BSP_Init(USB_OTG_CORE_HANDLE *pdev) {
|
|
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
|
|
|
|
/* Configure DM DP Pins on PA11 and PA12 */
|
|
GPIO_InitTypeDef GPIO_InitStructure;
|
|
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11 | GPIO_Pin_12;
|
|
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
|
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
|
|
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
|
|
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
|
|
GPIO_Init(GPIOA, &GPIO_InitStructure);
|
|
|
|
GPIO_PinAFConfig(GPIOA, GPIO_PinSource11, GPIO_AF_OTG_FS);
|
|
GPIO_PinAFConfig(GPIOA, GPIO_PinSource12, GPIO_AF_OTG_FS);
|
|
|
|
/* Configure VBUS Pin on PA9 (or disable VBUS_SENSING_ENABLED) */
|
|
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
|
|
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
|
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
|
|
GPIO_InitStructure.GPIO_OType = GPIO_OType_OD;
|
|
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
|
|
GPIO_Init(GPIOA, &GPIO_InitStructure);
|
|
|
|
// Configure ID pin on PA10
|
|
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
|
|
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
|
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
|
|
GPIO_InitStructure.GPIO_OType = GPIO_OType_OD;
|
|
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP ;
|
|
GPIO_Init(GPIOA, &GPIO_InitStructure);
|
|
GPIO_PinAFConfig(GPIOA, GPIO_PinSource10, GPIO_AF_OTG_FS);
|
|
|
|
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
|
|
RCC_AHB2PeriphClockCmd(RCC_AHB2Periph_OTG_FS, ENABLE);
|
|
}
|
|
|
|
/**
|
|
* @brief USB_OTG_BSP_EnableInterrupt
|
|
* Enable USB Global interrupt
|
|
* @param None
|
|
* @retval None
|
|
*/
|
|
void USB_OTG_BSP_EnableInterrupt(USB_OTG_CORE_HANDLE *pdev) {
|
|
// this assumes we use NVIC_PriorityGroup_4
|
|
NVIC_InitTypeDef NVIC_InitStructure;
|
|
NVIC_InitStructure.NVIC_IRQChannel = OTG_FS_IRQn;
|
|
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 8;
|
|
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
|
|
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
|
|
NVIC_Init(&NVIC_InitStructure);
|
|
}
|
|
|
|
/**
|
|
* @brief BSP_Drive_VBUS
|
|
* Drives the Vbus signal through IO
|
|
* @param state : VBUS states
|
|
* @retval None
|
|
*/
|
|
|
|
void USB_OTG_BSP_DriveVBUS(USB_OTG_CORE_HANDLE *pdev, uint8_t state) {
|
|
//printf("DriveVBUS %p %u\n", pdev, state);
|
|
/*
|
|
On-chip 5 V VBUS generation is not supported. For this reason, a charge pump
|
|
or, if 5 V are available on the application board, a basic power switch, must
|
|
be added externally to drive the 5 V VBUS line. The external charge pump can
|
|
be driven by any GPIO output. When the application decides to power on VBUS
|
|
using the chosen GPIO, it must also set the port power bit in the host port
|
|
control and status register (PPWR bit in OTG_FS_HPRT).
|
|
|
|
Bit 12 PPWR: Port power
|
|
The application uses this field to control power to this port, and the core
|
|
clears this bit on an overcurrent condition.
|
|
*/
|
|
#if 0 // not implemented
|
|
#ifndef USE_USB_OTG_HS
|
|
if (0 == state) {
|
|
/* DISABLE is needed on output of the Power Switch */
|
|
GPIO_SetBits(HOST_POWERSW_PORT, HOST_POWERSW_VBUS);
|
|
} else {
|
|
/*ENABLE the Power Switch by driving the Enable LOW */
|
|
GPIO_ResetBits(HOST_POWERSW_PORT, HOST_POWERSW_VBUS);
|
|
}
|
|
#endif
|
|
#endif
|
|
}
|
|
|
|
/**
|
|
* @brief USB_OTG_BSP_ConfigVBUS
|
|
* Configures the IO for the Vbus and OverCurrent
|
|
* @param None
|
|
* @retval None
|
|
*/
|
|
|
|
void USB_OTG_BSP_ConfigVBUS(USB_OTG_CORE_HANDLE *pdev) {
|
|
//printf("ConfigVBUS %p\n", pdev);
|
|
#if 0 // not implemented
|
|
#ifdef USE_USB_OTG_FS
|
|
GPIO_InitTypeDef GPIO_InitStructure;
|
|
|
|
#ifdef USE_STM3210C_EVAL
|
|
RCC_APB2PeriphClockCmd(HOST_POWERSW_PORT_RCC, ENABLE);
|
|
|
|
|
|
/* Configure Power Switch Vbus Pin */
|
|
GPIO_InitStructure.GPIO_Pin = HOST_POWERSW_VBUS;
|
|
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
|
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
|
|
GPIO_Init(HOST_POWERSW_PORT, &GPIO_InitStructure);
|
|
#else
|
|
#ifdef USE_USB_OTG_FS
|
|
RCC_AHB1PeriphClockCmd( RCC_AHB1Periph_GPIOH , ENABLE);
|
|
|
|
GPIO_InitStructure.GPIO_Pin = HOST_POWERSW_VBUS;
|
|
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
|
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
|
|
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
|
|
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
|
|
GPIO_Init(HOST_POWERSW_PORT,&GPIO_InitStructure);
|
|
#endif
|
|
#endif
|
|
|
|
/* By Default, DISABLE is needed on output of the Power Switch */
|
|
GPIO_SetBits(HOST_POWERSW_PORT, HOST_POWERSW_VBUS);
|
|
|
|
USB_OTG_BSP_mDelay(200); /* Delay is need for stabilising the Vbus Low
|
|
in Reset Condition, when Vbus=1 and Reset-button is pressed by user */
|
|
#endif
|
|
#endif
|
|
}
|
|
|
|
/**
|
|
* @brief USB_OTG_BSP_uDelay
|
|
* This function provides delay time in micro sec
|
|
* @param usec : Value of delay required in micro sec
|
|
* @retval None
|
|
*/
|
|
void USB_OTG_BSP_uDelay (const uint32_t usec)
|
|
{
|
|
uint32_t count = 0;
|
|
const uint32_t utime = (168 * usec / 5);
|
|
do
|
|
{
|
|
if ( ++count > utime )
|
|
{
|
|
return ;
|
|
}
|
|
}
|
|
while (1);
|
|
}
|
|
|
|
|
|
/**
|
|
* @brief USB_OTG_BSP_mDelay
|
|
* This function provides delay time in milli sec
|
|
* @param msec : Value of delay required in milli sec
|
|
* @retval None
|
|
*/
|
|
void USB_OTG_BSP_mDelay (const uint32_t msec)
|
|
{
|
|
USB_OTG_BSP_uDelay(msec * 1000);
|
|
}
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|