75 lines
2.5 KiB
C
75 lines
2.5 KiB
C
#define MICROPY_HW_BOARD_NAME "F429I-DISCO"
|
|
#define MICROPY_HW_MCU_NAME "STM32F429"
|
|
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
|
|
// HSE is 8MHz
|
|
#define MICROPY_HW_CLK_PLLM (8)
|
|
#define MICROPY_HW_CLK_PLLN (336)
|
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
|
|
#define MICROPY_HW_CLK_PLLQ (7)
|
|
|
|
// UART config
|
|
#define MICROPY_HW_UART1_TX (pin_A9)
|
|
#define MICROPY_HW_UART1_RX (pin_A10)
|
|
#define MICROPY_HW_UART2_TX (pin_D8)
|
|
#define MICROPY_HW_UART2_RX (pin_D9)
|
|
|
|
// I2C busses
|
|
#define MICROPY_HW_I2C3_SCL (pin_A8)
|
|
#define MICROPY_HW_I2C3_SDA (pin_C9)
|
|
|
|
// SPI busses
|
|
//#define MICROPY_HW_SPI1_NSS (pin_A4)
|
|
//#define MICROPY_HW_SPI1_SCK (pin_A5)
|
|
//#define MICROPY_HW_SPI1_MISO (pin_A6)
|
|
//#define MICROPY_HW_SPI1_MOSI (pin_A7)
|
|
#if defined(USE_USB_HS_IN_FS)
|
|
// The HS USB uses B14 & B15 for D- and D+
|
|
#else
|
|
#define MICROPY_HW_SPI2_NSS (pin_B12)
|
|
#define MICROPY_HW_SPI2_SCK (pin_B13)
|
|
#define MICROPY_HW_SPI2_MISO (pin_B14)
|
|
#define MICROPY_HW_SPI2_MOSI (pin_B15)
|
|
#endif
|
|
//#define MICROPY_HW_SPI4_NSS (pin_E11)
|
|
//#define MICROPY_HW_SPI4_SCK (pin_E12)
|
|
//#define MICROPY_HW_SPI4_MISO (pin_E13)
|
|
//#define MICROPY_HW_SPI4_MOSI (pin_E14)
|
|
#define MICROPY_HW_SPI5_NSS (pin_F6)
|
|
#define MICROPY_HW_SPI5_SCK (pin_F7)
|
|
#define MICROPY_HW_SPI5_MISO (pin_F8)
|
|
#define MICROPY_HW_SPI5_MOSI (pin_F9)
|
|
//#define MICROPY_HW_SPI6_NSS (pin_G8)
|
|
//#define MICROPY_HW_SPI6_SCK (pin_G13)
|
|
//#define MICROPY_HW_SPI6_MISO (pin_G12)
|
|
//#define MICROPY_HW_SPI6_MOSI (pin_G14)
|
|
|
|
// CAN busses
|
|
#define MICROPY_HW_CAN1_TX (pin_B9)
|
|
#define MICROPY_HW_CAN1_RX (pin_B8)
|
|
#define MICROPY_HW_CAN2_TX (pin_B13)
|
|
#define MICROPY_HW_CAN2_RX (pin_B12)
|
|
|
|
// USRSW is pulled low. Pressing the button makes the input go high.
|
|
#define MICROPY_HW_USRSW_PIN (pin_A0)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_G14) // red
|
|
#define MICROPY_HW_LED2 (pin_G13) // green
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
|
|
|
// USB config
|
|
#define MICROPY_HW_USB_HS (1)
|
|
#define MICROPY_HW_USB_HS_IN_FS (1)
|
|
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_B13)
|
|
#define MICROPY_HW_USB_OTG_ID_PIN (pin_B12)
|