92 lines
4.3 KiB
C
92 lines
4.3 KiB
C
#define MICROPY_HW_BOARD_NAME "NUCLEO_H563ZI"
|
|
#define MICROPY_HW_MCU_NAME "STM32H563ZI"
|
|
|
|
#define MICROPY_PY_PYB_LEGACY (0)
|
|
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (1)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_ADC (1)
|
|
#define MICROPY_HW_ENABLE_DAC (1)
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
|
|
// The board has a 8MHz oscillator, the following gives 250MHz CPU speed
|
|
#define MICROPY_HW_CLK_USE_BYPASS (1)
|
|
#define MICROPY_HW_CLK_PLLM (2)
|
|
#define MICROPY_HW_CLK_PLLN (125)
|
|
#define MICROPY_HW_CLK_PLLP (2)
|
|
#define MICROPY_HW_CLK_PLLQ (2)
|
|
#define MICROPY_HW_CLK_PLLR (2)
|
|
#define MICROPY_HW_CLK_PLLVCI_LL (LL_RCC_PLLINPUTRANGE_4_8)
|
|
#define MICROPY_HW_CLK_PLLVCO_LL (LL_RCC_PLLVCORANGE_WIDE)
|
|
#define MICROPY_HW_CLK_PLLFRAC (0)
|
|
|
|
// PLL3 with Q output at 48MHz for USB
|
|
// #define MICROPY_HW_CLK_USE_PLL3_FOR_USB
|
|
#define MICROPY_HW_CLK_PLL3M (8)
|
|
#define MICROPY_HW_CLK_PLL3N (192)
|
|
#define MICROPY_HW_CLK_PLL3P (2)
|
|
#define MICROPY_HW_CLK_PLL3Q (4)
|
|
#define MICROPY_HW_CLK_PLL3R (2)
|
|
#define MICROPY_HW_CLK_PLL3FRAC (0)
|
|
#define MICROPY_HW_CLK_PLL3VCI_LL (LL_RCC_PLLINPUTRANGE_1_2)
|
|
#define MICROPY_HW_CLK_PLL3VCO_LL (LL_RCC_PLLVCORANGE_MEDIUM)
|
|
|
|
// 5 wait states, according to Table 37, Reference Manual (RM0481 Rev 1)
|
|
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_5
|
|
|
|
// There is an external 32kHz oscillator
|
|
#define MICROPY_HW_RTC_USE_LSE (1)
|
|
|
|
// UART config
|
|
#define MICROPY_HW_UART1_TX (pin_B6) // SB14: Arduino Connector CN10-Pin14 (D1)
|
|
#define MICROPY_HW_UART1_RX (pin_B7) // SB63: Arduino Connector CN10-Pin16 (D0)
|
|
#define MICROPY_HW_UART3_TX (pin_D8) // SB23: ST-Link
|
|
#define MICROPY_HW_UART3_RX (pin_D9) // SB18: ST-Link
|
|
|
|
// Connect REPL to UART3 which is provided on ST-Link USB interface
|
|
#define MICROPY_HW_UART_REPL PYB_UART_3
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
|
|
|
// I2C buses
|
|
#define MICROPY_HW_I2C1_SCL (pin_B8) // Arduino Connector CN7-Pin2 (D15)
|
|
#define MICROPY_HW_I2C1_SDA (pin_B9) // Arduino Connector CN7-Pin4 (D14)
|
|
#define MICROPY_HW_I2C2_SCL (pin_F1) // Connector CN9-Pin19
|
|
#define MICROPY_HW_I2C2_SDA (pin_F0) // Connector CN9-Pin21
|
|
|
|
// SPI buses
|
|
// PD14 according to datasheet not working as SPI1_NSS, have to use as GPIO, not as AF
|
|
#define MICROPY_HW_SPI1_NSS (pin_D14) // Arduino Connector CN7-Pin16 (D10)
|
|
#define MICROPY_HW_SPI1_SCK (pin_A5) // Arduino Connector CN7-Pin10 (D13)
|
|
#define MICROPY_HW_SPI1_MISO (pin_G9) // Arduino Connector CN7-Pin12 (D12)
|
|
#define MICROPY_HW_SPI1_MOSI (pin_B5) // Arduino Connector CN7-Pin14 (D11)
|
|
|
|
// USRSW is pulled low. Pressing the button makes the input go high.
|
|
#define MICROPY_HW_USRSW_PIN (pin_C13)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_B0) // Green
|
|
#define MICROPY_HW_LED2 (pin_F4) // Orange
|
|
#define MICROPY_HW_LED3 (pin_G4) // Red
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
|
|
|
// USB config
|
|
#define MICROPY_HW_USB_FS (1)
|
|
#define MICROPY_HW_USB_MAIN_DEV (USB_PHY_FS_ID)
|
|
|
|
// Ethernet via RMII
|
|
#define MICROPY_HW_ETH_MDC (pin_C1)
|
|
#define MICROPY_HW_ETH_MDIO (pin_A2)
|
|
#define MICROPY_HW_ETH_RMII_REF_CLK (pin_A1)
|
|
#define MICROPY_HW_ETH_RMII_CRS_DV (pin_A7)
|
|
#define MICROPY_HW_ETH_RMII_RXD0 (pin_C4)
|
|
#define MICROPY_HW_ETH_RMII_RXD1 (pin_C5)
|
|
#define MICROPY_HW_ETH_RMII_TX_EN (pin_G11)
|
|
#define MICROPY_HW_ETH_RMII_TXD0 (pin_G13)
|
|
#define MICROPY_HW_ETH_RMII_TXD1 (pin_B15)
|