74 lines
2.7 KiB
C
74 lines
2.7 KiB
C
#define MICROPY_HW_BOARD_NAME "PYBv3"
|
|
#define MICROPY_HW_MCU_NAME "STM32F405RG"
|
|
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
|
#define MICROPY_HW_HAS_SDCARD (1)
|
|
#define MICROPY_HW_HAS_MMA7660 (1)
|
|
#define MICROPY_HW_HAS_LIS3DSH (0)
|
|
#define MICROPY_HW_HAS_LCD (0)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_TIMER (1)
|
|
#define MICROPY_HW_ENABLE_SERVO (1)
|
|
#define MICROPY_HW_ENABLE_DAC (1)
|
|
#define MICROPY_HW_ENABLE_SPI1 (1)
|
|
#define MICROPY_HW_ENABLE_SPI2 (1)
|
|
#define MICROPY_HW_ENABLE_SPI3 (0)
|
|
#define MICROPY_HW_ENABLE_CAN (1)
|
|
|
|
// HSE is 8MHz
|
|
#define MICROPY_HW_CLK_PLLM (8)
|
|
#define MICROPY_HW_CLK_PLLN (336)
|
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
|
|
#define MICROPY_HW_CLK_PLLQ (7)
|
|
|
|
// The pyboard has a 32kHz crystal for the RTC
|
|
#define MICROPY_HW_RTC_USE_LSE (1)
|
|
|
|
// UART config
|
|
#define MICROPY_HW_UART1_PORT (GPIOA)
|
|
#define MICROPY_HW_UART1_PINS (GPIO_PIN_9 | GPIO_PIN_10)
|
|
#define MICROPY_HW_UART2_PORT (GPIOA)
|
|
#define MICROPY_HW_UART2_PINS (GPIO_PIN_2 | GPIO_PIN_3)
|
|
#define MICROPY_HW_UART2_RTS (GPIO_PIN_1)
|
|
#define MICROPY_HW_UART2_CTS (GPIO_PIN_0)
|
|
#define MICROPY_HW_UART3_PORT (GPIOB)
|
|
#define MICROPY_HW_UART3_PINS (GPIO_PIN_10 | GPIO_PIN_11)
|
|
#define MICROPY_HW_UART3_RTS (GPIO_PIN_14)
|
|
#define MICROPY_HW_UART3_CTS (GPIO_PIN_13)
|
|
#define MICROPY_HW_UART4_PORT (GPIOA)
|
|
#define MICROPY_HW_UART4_PINS (GPIO_PIN_0 | GPIO_PIN_1)
|
|
#define MICROPY_HW_UART6_PORT (GPIOC)
|
|
#define MICROPY_HW_UART6_PINS (GPIO_PIN_6 | GPIO_PIN_7)
|
|
|
|
// X-skin: X9=PB6=SCL, X10=PB7=SDA
|
|
#define MICROPY_HW_I2C1_SCL (pin_B6)
|
|
#define MICROPY_HW_I2C1_SDA (pin_B7)
|
|
|
|
// Y-skin: Y9=PB10=SCL, Y10=PB11=SDA
|
|
#define MICROPY_HW_I2C2_SCL (pin_B10)
|
|
#define MICROPY_HW_I2C2_SDA (pin_B11)
|
|
|
|
// USRSW has no pullup or pulldown, and pressing the switch makes the input go low
|
|
#define MICROPY_HW_USRSW_PIN (pin_A13)
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP)
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
|
|
#define MICROPY_HW_USRSW_PRESSED (0)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pin_A8) // R1 - red
|
|
#define MICROPY_HW_LED2 (pin_A10) // R2 - red
|
|
#define MICROPY_HW_LED3 (pin_C4) // G1 - green
|
|
#define MICROPY_HW_LED4 (pin_C5) // G2 - green
|
|
#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP)
|
|
#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRH = pin->pin_mask)
|
|
#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRL = pin->pin_mask)
|
|
|
|
// SD card detect switch
|
|
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_C13)
|
|
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLDOWN)
|
|
#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_SET)
|
|
|
|
// USB VBUS detect pin
|
|
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
|