For now, the server will only send v6 configuration to mapversion 8 clients
as part of an early-adopter program, while we verify that the functionality
is robust.
Signed-off-by: David Anderson <danderson@tailscale.com>
In practice, we already provide IPv6 endpoint addresses via netcheck,
and that address is likely to match a local address anyway (i.e. no NAT66).
The comment at that piece of the code mentions needing to figure out a
good priority ordering, but that only applies to non-active-discovery
clients, who already don't do anything with IPv6 addresses.
Signed-off-by: David Anderson <danderson@tailscale.com>
Lazy wg configuration now triggers if a peer has only endpoint
addresses (/32 for IPv4, /128 for IPv6). Subnet routers still
trigger eager configuration to avoid the need for a CIDR match
in the hot packet path.
Signed-off-by: David Anderson <danderson@tailscale.com>
This caused some confusion in issue #460, since usually raw format
strings aren't printed directly. Hopefully by directly logging that
they are intended to be raw format strings, this will be more clear.
Rate limited format strings now look like:
[RATE LIMITED] format string "control: sendStatus: %s: %v"
Closes#460.
Signed-off-by: Smitty <me@smitop.com>
The previous code used a lot of whole-function variables and shared
behavior that only triggered based on prior action from a single codepath.
Instead of that, move the small amounts of "shared" code into each switch
case.
Signed-off-by: David Anderson <danderson@tailscale.com>
Before, tailscaled would log every 10 seconds when the periodic noteRecvActivity
call happens. This is noisy, but worse it's misleading, because the message
suggests that the disco code is starting a lazy config run for a missing peer,
whereas in fact it's just an internal piece of keepalive logic.
With this change, we still log when going from 0->1 tunnel for the peer, but
not every 10s thereafter.
Signed-off-by: David Anderson <danderson@tailscale.com>
Addresses #964
Still to be done:
- Figure out the correct logging lines in util/systemd
- Figure out if we need to slip the systemd.Status function anywhere
else
- Log util/systemd errors? (most of the errors are of the "you cannot do
anything about this, but it might be a bad idea to crash the program if
it errors" kind)
Assistance in getting this over the finish line would help a lot.
Signed-off-by: Christine Dodrill <me@christine.website>
util/systemd: rename the nonlinux file to appease the magic
Signed-off-by: Christine Dodrill <me@christine.website>
util/systemd: fix package name
Signed-off-by: Christine Dodrill <me@christine.website>
util/systemd: fix review feedback from @mdlayher
Signed-off-by: Christine Dodrill <me@christine.website>
cmd/tailscale{,d}: update depaware manifests
Signed-off-by: Christine Dodrill <me@christine.website>
util/systemd: use sync.Once instead of func init
Signed-off-by: Christine Dodrill <me@christine.website>
control/controlclient: minor review feedback fixes
Signed-off-by: Christine Dodrill <me@christine.website>
{control,ipn,systemd}: fix review feedback
Signed-off-by: Christine Dodrill <me@christine.website>
review feedback fixes
Signed-off-by: Christine Dodrill <me@christine.website>
ipn: fix sprintf call
Signed-off-by: Christine Dodrill <me@christine.website>
ipn: make staticcheck less sad
Signed-off-by: Christine Dodrill <me@christine.website>
ipn: print IP address in connected status
Signed-off-by: Christine Dodrill <me@christine.website>
ipn: review feedback
Signed-off-by: Christine Dodrill <me@christine.website>
final fixups
Signed-off-by: Christine Dodrill <me@christine.website>
Upgrading staticcheck upgraded golang.org/x/sync
(one downside of mixing our tools in with our regular go.mod),
which introduced a new dependency via
https://go-review.googlesource.com/c/sync/+/251677
That CL could and probably should be written without runtime/debug,
but it's not clear to me that that is better at this moment
than simply accepting the additional package as a dependency.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
These ignore built files that don't exist anymore, and just serve
to clutter up the .gitignore file. (I was initially confused when
I saw those lines, since I (correctly) thought that the only
Tailscale binaries were tailscale and tailscaled):
- taillogin was removed in d052586
- relaynode was removed in a56e853
Signed-off-by: Smitty <me@smitop.com>
This is a repeat of commit 3aa68cd397
which was lost in a rework of version.sh.
git worktrees have a .git file rather than a .git directory, so building
in a worktree caused version.sh to generate an error.
Signed-off-by: Adrian Dewhurst <adrian@tailscale.com>
After mapver 5's incremental netmap updates & user profiles, much of
the remaining bandwidth for streamed MapResponses were redundant,
unchanged PacketFilters. So make MapRequest.Version 6 mean that nil
means unchanged from the previous value.
David Anderson
Smitty
Brad Fitzpatrick
Christine Dodrill
Christine Dodrill
Josh Bleecher Snyder
Aleksandar Pesic
Adrian Dewhurst