This makes connectivity between ancient and new tailscale nodes slightly
worse in some cases, but only in cases where the ancient version would
likely have failed to get connectivity anyway.
Signed-off-by: David Anderson <danderson@tailscale.com>
In sendDiscoMessage there is a check of whether the connection is
closed, which is not being reliably exercised by other tests.
This shows up in code coverage reports, the lines of code in
sendDiscoMessage are alternately added and subtracted from
code coverage.
Add a test to specifically exercise and verify this code path.
Signed-off-by: Denton Gentry <dgentry@tailscale.com>
In derpWriteChanOfAddr when we call derphttp.NewRegionClient(),
there is a check of whether the connection is already errored and
if so it returns before grabbing the lock. The lock might already
be held and would be a deadlock.
This corner case is not being reliably exercised by other tests.
This shows up in code coverage reports, the lines of code in
derpWriteChanOfAddr are alternately added and subtracted from
code coverage.
Add a test to specifically exercise this code path, and verify that
it doesn't deadlock.
This is the best tradeoff I could come up with:
+ the moment code calls Err() to check if there is an error, we
grab the lock to make sure it would deadlock if it tries to grab
the lock itself.
+ if a new call to Err() is added in this code path, only the
first one will be covered and the rest will not be tested.
+ this test doesn't verify whether code is checking for Err() in
the right place, which ideally I guess it would.
Signed-off-by: Denton Gentry <dgentry@tailscale.com>
This is a replacement for the key-related parts
of the wireguard-go wgcfg package.
This is almost a straight copy/paste from the wgcfg package.
I have slightly changed some of the exported functions and types
to avoid stutter, added and tweaked some comments,
and removed some now-unused code.
To avoid having wireguard-go depend on this new package,
wgcfg will keep its key types.
We translate into and out of those types at the last minute.
These few remaining uses will be eliminated alongside
the rest of the wgcfg package.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
We still use the packet.* alloc-free types in the data path, but
the compilation from netaddr to packet happens within the filter
package.
Signed-off-by: David Anderson <danderson@tailscale.com>
Updates #654. See that issue for a discussion of why
this timeout reduces flakiness, and what next steps are.
Signed-off-by: Josh Bleecher Snyder <josh@tailscale.com>
1) we weren't waking up a discoEndpoint that once existed and
went idle for 5 minutes and then got a disco message again.
2) userspaceEngine.noteReceiveActivity had a buggy check; fixed
and added a test
There is a race in natlab where we might start shutdown while natlab is still running
a goroutine or two to deliver packets. This adds a small grace period to try and receive
it before continuing shutdown.
Signed-off-by: David Anderson <danderson@tailscale.com>
The first packet to transit may take several seconds to do so, because
setup rates in wgengine may result in the initial WireGuard handshake
init to get dropped. So, we have to wait at least long enough for a
retransmit to correct the fault.
Signed-off-by: David Anderson <danderson@tailscale.com>
Active discovery lets us introspect the state of the network stack precisely
enough that it's unnecessary, and dropping the initial DERP packets greatly
slows down tests. Additionally, it's unrealistic since our production network
will never deliver _only_ discovery packets, it'll be all or nothing.
Signed-off-by: David Anderson <danderson@tailscale.com>
Uses natlab only, because the point of this active discovery test is going to be
that it should get through a lot of obstacles.
Signed-off-by: David Anderson <danderson@tailscale.com>
wireguard-go uses 3 goroutines per peer (with reasonably large stacks
& buffers).
Rather than tell wireguard-go about all our peers, only tell it about
peers we're actively communicating with. That means we need hooks into
magicsock's packet receiving path and tstun's packet sending path to
lazily create a wireguard peer on demand from the network map.
This frees up lots of memory for iOS (where we have almost nothing
left for larger domains with many users).
We should ideally do this in wireguard-go itself one day, but that'd
be a pretty big change.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
The new interface lets implementors more precisely distinguish
local traffic from forwarded traffic, and applies different
forwarding logic within Machines for each type. This allows
Machines to be packet forwarders, which didn't quite work
with the implementation of Inject.
Signed-off-by: David Anderson <danderson@tailscale.com>
The test demonstrates that magicsock can traverse two stateful
firewalls facing each other, that each require localhost to
initiate connections.
Signed-off-by: David Anderson <danderson@tailscale.com>
This adds a new magicsock endpoint type only used when both sides
support discovery (that is, are advertising a discovery
key). Otherwise the old code is used.
So far the new code only communicates over DERP as proof that the new
code paths are wired up. None of the actually discovery messaging is
implemented yet.
Support for discovery (generating and advertising a key) are still
behind an environment variable for now.
Updates #483
And track known peers.
Doesn't yet do anything with the messages. (nor does it send any yet)
Start of docs on the message format. More will come in subsequent changes.
Updates #483
David Anderson
Denton Gentry
Josh Bleecher Snyder
Brad Fitzpatrick
Dmytro Shynkevych