2017-05-13 12:02:10 +01:00
/*
2018-10-26 16:13:17 +01:00
my_user_config . h - user specific configuration for Sonoff - Tasmota
2017-05-13 12:02:10 +01:00
2019-01-01 12:55:01 +00:00
Copyright ( C ) 2019 Theo Arends
2017-05-13 12:02:10 +01:00
This program is free software : you can redistribute it and / or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation , either version 3 of the License , or
( at your option ) any later version .
This program is distributed in the hope that it will be useful ,
but WITHOUT ANY WARRANTY ; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE . See the
GNU General Public License for more details .
You should have received a copy of the GNU General Public License
along with this program . If not , see < http : //www.gnu.org/licenses/>.
*/
2018-10-26 16:13:17 +01:00
# ifndef _MY_USER_CONFIG_H_
# define _MY_USER_CONFIG_H_
2017-10-18 17:22:34 +01:00
2017-01-28 13:41:01 +00:00
/*********************************************************************************************\
2018-04-05 14:26:16 +01:00
* This file consists of TWO sections .
2017-01-28 13:41:01 +00:00
*
2018-04-05 14:26:16 +01:00
* SECTION 1 :
* The first section contains PARAMETERS overriding flash settings if define CFG_HOLDER is CHANGED .
* All parameters can be persistent changed online using commands via MQTT , WebConsole or Serial .
* Corresponding MQTT / Serial / Console commands are shown in [ brackets ]
*
* SECTION 2 :
* The second section contains Enabled and Disabled FEATURES allowing different program size .
* Changes in this section do NOT need a change of define CFG_HOLDER .
*
* ATTENTION :
2018-04-05 15:13:17 +01:00
* Users are advised to use the user_config_override . h file for most changes .
2017-01-28 13:41:01 +00:00
\ * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
2018-04-05 14:26:16 +01:00
//#define USE_CONFIG_OVERRIDE // Uncomment to use user_config_override.h file. See README.md
2017-09-02 13:37:02 +01:00
2018-04-05 14:26:16 +01:00
/*********************************************************************************************\
* SECTION 1
2018-04-05 15:13:17 +01:00
* - After initial load any change here only take effect if CFG_HOLDER is changed too
2018-04-05 14:26:16 +01:00
\ * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
2017-01-28 13:41:01 +00:00
2018-04-05 14:26:16 +01:00
// -- Master parameter control --------------------
2018-07-06 17:00:50 +01:00
# define CFG_HOLDER 4617 // [Reset 1] Change this value (max 32000) to load SECTION1 configuration parameters to flash
2018-04-02 10:24:36 +01:00
2018-04-05 14:26:16 +01:00
// -- Project -------------------------------------
# define PROJECT "sonoff" // PROJECT is used as the default topic delimiter
2018-12-15 14:55:51 +00:00
// If not selected the default will be SONOFF_BASIC
//#define MODULE SONOFF_BASIC // [Module] Select default model from sonoff_template.h
2018-04-02 10:24:36 +01:00
2017-01-28 13:41:01 +00:00
# define SAVE_DATA 1 // [SaveData] Save changed parameters to Flash (0 = disable, 1 - 3600 seconds)
2017-07-30 16:55:37 +01:00
# define SAVE_STATE 1 // [SetOption0] Save changed power state to Flash (0 = disable, 1 = enable)
2019-01-30 13:34:31 +00:00
# define BOOT_LOOP_OFFSET 1 // [SetOption36] Number of boot loops before starting restoring defaults (0 = disable, 1..200 = boot loops offset)
2017-01-28 13:41:01 +00:00
// -- Wifi ----------------------------------------
2019-01-08 21:12:09 +00:00
# define WIFI_IP_ADDRESS "0.0.0.0" // [IpAddress1] Set to 0.0.0.0 for using DHCP or enter a static IP address
2018-10-26 16:13:17 +01:00
# define WIFI_GATEWAY "192.168.1.1" // [IpAddress2] If not using DHCP set Gateway IP address
2017-03-29 17:42:05 +01:00
# define WIFI_SUBNETMASK "255.255.255.0" // [IpAddress3] If not using DHCP set Network mask
2018-10-26 16:13:17 +01:00
# define WIFI_DNS "192.168.1.1" // [IpAddress4] If not using DHCP set DNS IP address (might be equal to WIFI_GATEWAY)
2017-03-25 16:24:11 +00:00
2018-02-10 14:13:27 +00:00
# define STA_SSID1 "" // [Ssid1] Wifi SSID
# define STA_PASS1 "" // [Password1] Wifi password
# define STA_SSID2 "" // [Ssid2] Optional alternate AP Wifi SSID
# define STA_PASS2 "" // [Password2] Optional alternate AP Wifi password
2018-12-15 14:55:51 +00:00
# define WIFI_CONFIG_TOOL WIFI_RETRY // [WifiConfig] Default tool if wifi fails to connect
2018-07-15 14:21:48 +01:00
// (WIFI_RESTART, WIFI_SMARTCONFIG, WIFI_MANAGER, WIFI_WPSCONFIG, WIFI_RETRY, WIFI_WAIT, WIFI_SERIAL)
2018-07-15 16:30:38 +01:00
# define WIFI_CONFIG_NO_SSID WIFI_WPSCONFIG // Default tool if wifi fails to connect and no SSID is configured
2018-07-15 14:21:48 +01:00
// (WIFI_SMARTCONFIG, WIFI_MANAGER, WIFI_WPSCONFIG, WIFI_SERIAL)
2018-07-14 14:35:56 +01:00
// *** NOTE: When WPS is disabled by USE_WPS below, WIFI_WPSCONFIG will execute WIFI_MANAGER ***
2018-07-15 14:21:48 +01:00
// *** NOTE: When WIFI_MANAGER is disabled by USE_WEBSERVER below, WIFI_MANAGER will execute WIFI_SMARTCONFIG ***
// *** NOTE: When WIFI_SMARTCONFIG is disabled by USE_SMARTCONFIG below, WIFI_SMARTCONFIG will execute WIFI_SERIAL ***
2017-09-02 13:37:02 +01:00
2017-01-28 13:41:01 +00:00
// -- Syslog --------------------------------------
2018-02-10 14:13:27 +00:00
# define SYS_LOG_HOST "" // [LogHost] (Linux) syslog host
2017-01-28 13:41:01 +00:00
# define SYS_LOG_PORT 514 // [LogPort] default syslog UDP port
2018-04-12 13:01:43 +01:00
# define SYS_LOG_LEVEL LOG_LEVEL_NONE // [SysLog] (LOG_LEVEL_NONE, LOG_LEVEL_ERROR, LOG_LEVEL_INFO, LOG_LEVEL_DEBUG, LOG_LEVEL_DEBUG_MORE)
# define SERIAL_LOG_LEVEL LOG_LEVEL_INFO // [SerialLog] (LOG_LEVEL_NONE, LOG_LEVEL_ERROR, LOG_LEVEL_INFO, LOG_LEVEL_DEBUG, LOG_LEVEL_DEBUG_MORE)
# define WEB_LOG_LEVEL LOG_LEVEL_INFO // [WebLog] (LOG_LEVEL_NONE, LOG_LEVEL_ERROR, LOG_LEVEL_INFO, LOG_LEVEL_DEBUG, LOG_LEVEL_DEBUG_MORE)
2017-01-28 13:41:01 +00:00
// -- Ota -----------------------------------------
2018-10-27 12:33:17 +01:00
# define OTA_URL "http: //thehackbox.org/tasmota/release/sonoff.bin" // [OtaUrl]
2018-03-02 14:38:37 +00:00
2017-01-28 13:41:01 +00:00
// -- MQTT ----------------------------------------
2017-07-30 16:55:37 +01:00
# define MQTT_USE 1 // [SetOption3] Select default MQTT use (0 = Off, 1 = On)
2018-03-02 14:38:37 +00:00
2018-04-05 14:26:16 +01:00
# define MQTT_HOST "" // [MqttHost]
# define MQTT_FINGERPRINT1 "A5 02 FF 13 99 9F 8B 39 8E F1 83 4F 11 23 65 0B 32 36 FC 07" // [MqttFingerprint1]
# define MQTT_FINGERPRINT2 "A5 02 FF 13 99 9F 8B 39 8E F1 83 4F 11 23 65 0B 32 36 FC 07" // [MqttFingerprint2]
# define MQTT_PORT 1883 // [MqttPort] MQTT port (10123 on CloudMQTT)
# define MQTT_USER "DVES_USER" // [MqttUser] MQTT user
# define MQTT_PASS "DVES_PASS" // [MqttPassword] MQTT password
2017-01-28 13:41:01 +00:00
# define MQTT_BUTTON_RETAIN 0 // [ButtonRetain] Button may send retain flag (0 = off, 1 = on)
# define MQTT_POWER_RETAIN 0 // [PowerRetain] Power status message may send retain flag (0 = off, 1 = on)
# define MQTT_SWITCH_RETAIN 0 // [SwitchRetain] Switch may send retain flag (0 = off, 1 = on)
2018-12-15 14:55:51 +00:00
# define MQTT_BUTTON_SWITCH_FORCE_LOCAL 0 // [SetOption61] Force local operation when button/switch topic is set (0 = off, 1 = on)
2017-01-28 13:41:01 +00:00
2017-03-29 17:42:05 +01:00
# define MQTT_STATUS_OFF "OFF" // [StateText1] Command or Status result when turned off (needs to be a string like "0" or "Off")
# define MQTT_STATUS_ON "ON" // [StateText2] Command or Status result when turned on (needs to be a string like "1" or "On")
# define MQTT_CMND_TOGGLE "TOGGLE" // [StateText3] Command to send when toggling (needs to be a string like "2" or "Toggle")
2017-06-06 22:23:23 +01:00
# define MQTT_CMND_HOLD "HOLD" // [StateText4] Command to send when button is kept down for over KEY_HOLD_TIME * 0.1 seconds (needs to be a string like "HOLD")
2017-01-28 13:41:01 +00:00
2017-05-08 12:21:45 +01:00
// -- MQTT topics ---------------------------------
2018-04-05 14:26:16 +01:00
// Example "tasmota/bedroom/%topic%/%prefix%/" up to 80 characers
2017-05-08 12:21:45 +01:00
# define MQTT_FULLTOPIC "%prefix% / %topic% / " // [FullTopic] Subscribe and Publish full topic name - Legacy topic
// %prefix% token options
# define SUB_PREFIX "cmnd" // [Prefix1] Sonoff devices subscribe to %prefix%/%topic% being SUB_PREFIX/MQTT_TOPIC and SUB_PREFIX/MQTT_GRPTOPIC
# define PUB_PREFIX "stat" // [Prefix2] Sonoff devices publish to %prefix%/%topic% being PUB_PREFIX/MQTT_TOPIC
# define PUB_PREFIX2 "tele" // [Prefix3] Sonoff devices publish telemetry data to %prefix%/%topic% being PUB_PREFIX2/MQTT_TOPIC/UPTIME, POWER and TIME
// May be named the same as PUB_PREFIX
// %topic% token options (also ButtonTopic and SwitchTopic)
2018-08-05 19:01:50 +01:00
# define MQTT_TOPIC PROJECT // [Topic] (unique) MQTT device topic, set to 'PROJECT "_%06X"' for unique topic including device MAC address
2017-05-08 12:21:45 +01:00
# define MQTT_GRPTOPIC "sonoffs" // [GroupTopic] MQTT Group topic
2018-08-05 19:01:50 +01:00
# define MQTT_BUTTON_TOPIC "0" // [ButtonTopic] MQTT button topic, "0" = same as MQTT_TOPIC, set to 'PROJECT "_BTN_%06X"' for unique topic including device MAC address
# define MQTT_SWITCH_TOPIC "0" // [SwitchTopic] MQTT button topic, "0" = same as MQTT_TOPIC, set to 'PROJECT "_SW_%06X"' for unique topic including device MAC address
2017-05-08 12:21:45 +01:00
# define MQTT_CLIENT_ID "DVES_%06X" // [MqttClient] Also fall back topic using Chip Id = last 6 characters of MAC address
2017-01-28 13:41:01 +00:00
// -- MQTT - Telemetry ----------------------------
# define TELE_PERIOD 300 // [TelePeriod] Telemetry (0 = disable, 10 - 3600 seconds)
2019-02-17 21:05:02 +00:00
# define TELE_ON_POWER 0 // [SetOption59] send tele/STATE together with stat/RESULT (0 = Disable, 1 = Enable)
2017-01-28 13:41:01 +00:00
// -- MQTT - Domoticz -----------------------------
2018-04-05 14:26:16 +01:00
# define DOMOTICZ_UPDATE_TIMER 0 // [DomoticzUpdateTimer] Send relay status (0 = disable, 1 - 3600 seconds)
2017-01-28 13:41:01 +00:00
2018-01-18 15:19:28 +00:00
// -- MQTT - Home Assistant Discovery -------------
2018-04-05 14:26:16 +01:00
# define HOME_ASSISTANT_DISCOVERY_ENABLE 0 // [SetOption19] Home Assistant Discovery (0 = Disable, 1 = Enable)
2018-01-18 15:19:28 +00:00
2017-01-28 13:41:01 +00:00
// -- HTTP ----------------------------------------
2018-04-05 14:26:16 +01:00
# define WEB_SERVER 2 // [WebServer] Web server (0 = Off, 1 = Start as User, 2 = Start as Admin)
# define WEB_PASSWORD "" // [WebPassword] Web server Admin mode Password for WEB_USERNAME (empty string = Disable)
# define FRIENDLY_NAME "Sonoff" // [FriendlyName] Friendlyname up to 32 characters used by webpages and Alexa
# define EMULATION EMUL_NONE // [Emulation] Select Belkin WeMo (single relay/light) or Hue Bridge emulation (multi relay/light) (EMUL_NONE, EMUL_WEMO or EMUL_HUE)
2017-01-28 13:41:01 +00:00
2019-01-14 09:57:01 +00:00
// -- mDNS ----------------------------------------
# define MDNS_ENABLED 0 // [SetOption55] Use mDNS (0 = Disable, 1 = Enable)
2017-01-28 13:41:01 +00:00
// -- Time - Up to three NTP servers in your region
2017-03-12 17:36:33 +00:00
# define NTP_SERVER1 "pool.ntp.org" // [NtpServer1] Select first NTP server by name or IP address (129.250.35.250)
# define NTP_SERVER2 "nl.pool.ntp.org" // [NtpServer2] Select second NTP server by name or IP address (5.39.184.5)
# define NTP_SERVER3 "0.nl.pool.ntp.org" // [NtpServer3] Select third NTP server by name or IP address (93.94.224.67)
2017-01-28 13:41:01 +00:00
2018-05-13 18:43:48 +01:00
// -- Time - Start Daylight Saving Time and timezone offset from UTC in minutes
2018-10-26 16:13:17 +01:00
# define TIME_DST_HEMISPHERE North // [TimeDst] Hemisphere (0 or North, 1 or South)
# define TIME_DST_WEEK Last // Week of month (0 or Last, 1 or First, 2 or Second, 3 or Third, 4 or Fourth)
# define TIME_DST_DAY Sun // Day of week (1 or Sun, 2 or Mon, 3 or Tue, 4 or Wed, 5 or Thu, 6 or Fri, 7 or Sat)
# define TIME_DST_MONTH Mar // Month (1 or Jan, 2 or Feb, 3 or Mar, 4 or Apr, 5 or May, 6 or Jun, 7 or Jul, 8 or Aug, 9 or Sep, 10 or Oct, 11 or Nov, 12 or Dec)
# define TIME_DST_HOUR 2 // Hour (0 to 23)
# define TIME_DST_OFFSET +120 // Offset from UTC in minutes (-780 to +780)
2018-05-13 18:43:48 +01:00
// -- Time - Start Standard Time and timezone offset from UTC in minutes
2018-10-26 16:13:17 +01:00
# define TIME_STD_HEMISPHERE North // [TimeStd] Hemisphere (0 or North, 1 or South)
# define TIME_STD_WEEK Last // Week of month (0 or Last, 1 or First, 2 or Second, 3 or Third, 4 or Fourth)
# define TIME_STD_DAY Sun // Day of week (1 or Sun, 2 or Mon, 3 or Tue, 4 or Wed, 5 or Thu, 6 or Fri, 7 or Sat)
# define TIME_STD_MONTH Oct // Month (1 or Jan, 2 or Feb, 3 or Mar, 4 or Apr, 5 or May, 6 or Jun, 7 or Jul, 8 or Aug, 9 or Sep, 10 or Oct, 11 or Nov, 12 or Dec)
# define TIME_STD_HOUR 3 // Hour (0 to 23)
# define TIME_STD_OFFSET +60 // Offset from UTC in minutes (-780 to +780)
2018-05-13 18:43:48 +01:00
2018-04-05 14:26:16 +01:00
// -- Location ------------------------------------
# define LATITUDE 48.858360 // [Latitude] Your location to be used with sunrise and sunset
# define LONGITUDE 2.294442 // [Longitude] Your location to be used with sunrise and sunset
2017-01-28 13:41:01 +00:00
// -- Application ---------------------------------
2018-04-05 14:26:16 +01:00
# define APP_TIMEZONE 1 // [Timezone] +1 hour (Amsterdam) (-13 .. 14 = hours from UTC, 99 = use TIME_DST/TIME_STD)
# define APP_LEDSTATE LED_POWER // [LedState] Function of led
// (LED_OFF, LED_POWER, LED_MQTTSUB, LED_POWER_MQTTSUB, LED_MQTTPUB, LED_POWER_MQTTPUB, LED_MQTT, LED_POWER_MQTT)
2017-01-28 13:41:01 +00:00
# define APP_PULSETIME 0 // [PulseTime] Time in 0.1 Sec to turn off power for relay 1 (0 = disabled)
2018-04-05 14:26:16 +01:00
# define APP_POWERON_STATE POWER_ALL_SAVED // [PowerOnState] Power On Relay state
// (POWER_ALL_OFF, POWER_ALL_ON, POWER_ALL_SAVED_TOGGLE, POWER_ALL_SAVED, POWER_ALL_ALWAYS_ON, POWER_ALL_OFF_PULSETIME_ON)
2017-01-28 13:41:01 +00:00
# define APP_BLINKTIME 10 // [BlinkTime] Time in 0.1 Sec to blink/toggle power for relay 1
# define APP_BLINKCOUNT 10 // [BlinkCount] Number of blinks (0 = 32000)
2017-02-13 16:25:46 +00:00
# define APP_SLEEP 0 // [Sleep] Sleep time to lower energy consumption (0 = Off, 1 - 250 mSec)
2017-01-28 13:41:01 +00:00
2018-08-27 11:01:20 +01:00
# define KEY_DEBOUNCE_TIME 50 // [ButtonDebounce] Number of mSeconds button press debounce time
2017-06-16 13:33:49 +01:00
# define KEY_HOLD_TIME 40 // [SetOption32] Number of 0.1 seconds to hold Button or external Pushbutton before sending HOLD message
2018-08-27 11:01:20 +01:00
# define SWITCH_DEBOUNCE_TIME 50 // [SwitchDebounce] Number of mSeconds switch press debounce time
2018-04-05 14:26:16 +01:00
# define SWITCH_MODE TOGGLE // [SwitchMode] TOGGLE, FOLLOW, FOLLOW_INV, PUSHBUTTON, PUSHBUTTON_INV, PUSHBUTTONHOLD, PUSHBUTTONHOLD_INV, PUSHBUTTON_TOGGLE (the wall switch state)
# define WS2812_LEDS 30 // [Pixels] Number of WS2812 LEDs to start with (max is 512)
2017-01-28 13:41:01 +00:00
2017-07-30 16:55:37 +01:00
# define TEMP_CONVERSION 0 // [SetOption8] Return temperature in (0 = Celsius or 1 = Fahrenheit)
2018-12-15 14:55:51 +00:00
# define PRESSURE_CONVERSION 0 // [SetOption24] Return pressure in (0 = hPa or 1 = mmHg)
2017-05-03 17:19:13 +01:00
# define TEMP_RESOLUTION 1 // [TempRes] Maximum number of decimals (0 - 3) showing sensor Temperature
# define HUMIDITY_RESOLUTION 1 // [HumRes] Maximum number of decimals (0 - 3) showing sensor Humidity
# define PRESSURE_RESOLUTION 1 // [PressRes] Maximum number of decimals (0 - 3) showing sensor Pressure
# define ENERGY_RESOLUTION 3 // [EnergyRes] Maximum number of decimals (0 - 5) showing energy usage in kWh
2018-12-15 14:55:51 +00:00
# define CALC_RESOLUTION 3 // [CalcRes] Maximum number of decimals (0 - 7) used in commands ADD, SUB, MULT and SCALE
2017-01-28 13:41:01 +00:00
2018-04-05 14:26:16 +01:00
/*********************************************************************************************\
* END OF SECTION 1
*
* SECTION 2
* - Enable a feature by removing both // in front of it
* - Disable a feature by preceding it with //
\ * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
// -- Localization --------------------------------
// If non selected the default en-GB will be used
2018-04-20 15:07:06 +01:00
//#define MY_LANGUAGE bg-BG // Bulgarian in Bulgaria
2018-04-05 14:26:16 +01:00
//#define MY_LANGUAGE cs-CZ // Czech in Czech
//#define MY_LANGUAGE de-DE // German in Germany
2018-04-19 20:57:14 +01:00
//#define MY_LANGUAGE el-GR // Greek in Greece
2018-04-05 14:26:16 +01:00
//#define MY_LANGUAGE en-GB // English in Great Britain. Enabled by Default
//#define MY_LANGUAGE es-AR // Spanish in Argentina
//#define MY_LANGUAGE fr-FR // French in France
2018-10-26 16:13:17 +01:00
//#define MY_LANGUAGE he-HE // Hebrew in Israel
2018-04-05 14:26:16 +01:00
//#define MY_LANGUAGE hu-HU // Hungarian in Hungary
//#define MY_LANGUAGE it-IT // Italian in Italy
2019-02-26 09:16:56 +00:00
//#define MY_LANGUAGE ko-KO // Korean in Korea
2018-04-05 14:26:16 +01:00
//#define MY_LANGUAGE nl-NL // Dutch in the Netherlands
//#define MY_LANGUAGE pl-PL // Polish in Poland
2018-05-04 14:39:18 +01:00
//#define MY_LANGUAGE pt-BR // Portuguese in Brazil
2018-04-05 14:26:16 +01:00
//#define MY_LANGUAGE pt-PT // Portuguese in Portugal
//#define MY_LANGUAGE ru-RU // Russian in Russia
2018-12-18 17:57:37 +00:00
//#define MY_LANGUAGE sk-SK // Slovak in Slovakia
2018-12-15 14:55:51 +00:00
//#define MY_LANGUAGE sv-SE // Swedish in Sweden
2018-07-26 09:57:59 +01:00
//#define MY_LANGUAGE tr-TR // Turkish in Turkey
2018-05-29 13:47:53 +01:00
//#define MY_LANGUAGE uk-UK // Ukrainian in Ukrain
2018-04-05 14:26:16 +01:00
//#define MY_LANGUAGE zh-CN // Chinese (Simplified) in China
//#define MY_LANGUAGE zh-TW // Chinese (Traditional) in Taiwan
2018-07-15 16:30:38 +01:00
// -- Wifi Config tools ---------------------------
2018-12-22 15:13:07 +00:00
# define WIFI_SOFT_AP_CHANNEL 1 // Soft Access Point Channel number between 1 and 13 as used by Wifi Manager web GUI
2018-07-14 14:35:56 +01:00
//#define USE_WPS // Add support for WPS as initial wifi configuration tool (+33k code, 1k mem (5k mem with core v2.4.2+))
2018-07-15 14:21:48 +01:00
//#define USE_SMARTCONFIG // Add support for Wifi SmartConfig as initial wifi configuration tool (+23k code, +0.6k mem)
2018-07-14 14:35:56 +01:00
// -- OTA -----------------------------------------
//#define USE_ARDUINO_OTA // Add optional support for Arduino OTA (+13k code)
2018-04-05 14:26:16 +01:00
/*-------------------------------------------------------------------------------------------*\
2018-10-26 16:13:17 +01:00
* Select ONE of possible MQTT library types below
2018-04-05 14:26:16 +01:00
\ * - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - */
2018-10-26 16:13:17 +01:00
// Default MQTT driver for both non-TLS and TLS connections. Latest library version (20181016) does not block network if MQTT server is unavailable.
2018-06-05 22:54:35 +01:00
# define MQTT_LIBRARY_TYPE MQTT_PUBSUBCLIENT // Use PubSubClient library
2018-04-05 14:26:16 +01:00
// Alternative MQTT driver does not block network when MQTT server is unavailable. No TLS support
2018-10-26 16:13:17 +01:00
//#define MQTT_LIBRARY_TYPE MQTT_TASMOTAMQTT // Use TasmotaMqtt library (+4k4 (core 2.3.0), +14k4 (core 2.4.2 lwip2) code, +4k mem) - non-TLS only
// Alternative MQTT driver does not block network when MQTT server is unavailable. TLS should work but needs to be tested.
//#define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT // Use arduino-mqtt (lwmqtt) library (+3k3 code, +2k mem)
2018-04-05 14:26:16 +01:00
2018-04-25 11:06:53 +01:00
// -- MQTT ----------------------------------------
# define MQTT_TELE_RETAIN 0 // Tele messages may send retain flag (0 = off, 1 = on)
2018-04-05 14:26:16 +01:00
// -- MQTT - Domoticz -----------------------------
# define USE_DOMOTICZ // Enable Domoticz (+6k code, +0.3k mem)
# define DOMOTICZ_IN_TOPIC "domoticz / in" // Domoticz Input Topic
# define DOMOTICZ_OUT_TOPIC "domoticz / out" // Domoticz Output Topic
// -- MQTT - Home Assistant Discovery -------------
2018-06-05 22:54:35 +01:00
# define USE_HOME_ASSISTANT // Enable Home Assistant Discovery Support (+2k code)
2018-04-05 14:26:16 +01:00
# define HOME_ASSISTANT_DISCOVERY_PREFIX "homeassistant" // Home Assistant discovery prefix
// -- MQTT - TLS ----------------------------------
// !!! TLS uses a LOT OF MEMORY so be careful to enable other options at the same time !!!
//#define USE_MQTT_TLS // Use TLS for MQTT connection (+53k code, +15k mem)
2018-12-22 17:09:27 +00:00
// #define USE_MQTT_TLS_CA_CERT // Use LetsEncrypt Certificate from sonoff_letsencrypt.h - Not supported with core 2.3.0
2018-04-05 14:26:16 +01:00
2018-04-18 16:28:45 +01:00
// -- KNX IP Protocol -----------------------------
2018-07-23 04:54:25 +01:00
//#define USE_KNX // Enable KNX IP Protocol Support (+9.4k code, +3k7 mem)
# define USE_KNX_WEB_MENU // Enable KNX WEB MENU (+8.3k code, +144 mem)
2018-04-18 16:28:45 +01:00
2018-04-05 14:26:16 +01:00
// -- HTTP ----------------------------------------
2018-07-15 14:21:48 +01:00
# define USE_WEBSERVER // Enable web server and Wifi Manager (+66k code, +8k mem)
2018-04-05 14:26:16 +01:00
# define WEB_PORT 80 // Web server Port for User and Admin mode
# define WEB_USERNAME "admin" // Web server Admin mode user name
# define USE_EMULATION // Enable Belkin WeMo and Hue Bridge emulation for Alexa (+16k code, +2k mem)
// -- mDNS ----------------------------------------
2018-06-05 22:54:35 +01:00
# define USE_DISCOVERY // Enable mDNS for the following services (+8k code, +0.3k mem)
2018-04-05 14:26:16 +01:00
# define WEBSERVER_ADVERTISE // Provide access to webserver by name <Hostname>.local/
# define MQTT_HOST_DISCOVERY // Find MQTT host server (overrides MQTT_HOST if found)
// -- Time ----------------------------------------
# define USE_TIMERS // Add support for up to 16 timers (+2k2 code)
# define USE_TIMERS_WEB // Add timer webpage support (+4k5 code)
# define USE_SUNRISE // Add support for Sunrise and sunset tools (+16k)
2018-04-23 10:37:46 +01:00
# define SUNRISE_DAWN_ANGLE DAWN_NORMAL // Select desired Dawn Angle from (DAWN_NORMAL, DAWN_CIVIL, DAWN_NAUTIC, DAWN_ASTRONOMIC)
2018-04-05 14:26:16 +01:00
2018-04-13 16:42:11 +01:00
// -- Rules ---------------------------------------
# define USE_RULES // Add support for rules (+4k4 code)
2019-02-16 15:17:17 +00:00
# define USE_EXPRESSION // Add support for expression evaluation in rules (+3k2 code, +64 bytes mem)
Rules: Trigger Event with MQTT Subscriptions
Support subscribe/unsubscribe MQTT topics and trigger specified event with the subscribed MQTT topic.
You can subscribe a MQTT topic and assign an event name. Once we received subscribed MQTT message, an event will be automatically triggered. So you can set up a rule with "ON EVENT#<event_name> DO ..." to do whatever you want based on this MQTT message. The payload is passed as a parameter once the event been triggered. If the payload is in JSON format, you are able to get the value of specified key as parameter.
For example, if you have a Tasmota based thermostat and multiple temperature sensors in different place, usually you have to set up a centre home automation system like Domoticz to control the thermostat. Right now, with this new feature, you can write a rule to do this.
Two new commands in Rules:
1. Subscribe
Subscribe a MQTT topic (with or without key) and assign an event name to it.
Command format:
Subscribe [<event_name>, <topic> [, <key>]]
This command will subscribe a <topic> and give it an event name <event_name>.
The optional parameter <key> is for parse the specified key/value from MQTT message
payload with JSON format.
In order to parse value from two level JSON data, you can use one dot (".") to split the key into two section.
Subscribe command without any parameter will list all topics currently subscribed.
2. Unsubscribe
Unsubscribe specified MQTT event.
Command format:
Unsubscribe [<event_name>]
Unsubscribe a topic subscribed by specify the event name.
If no event specified, Unsubscribe all topics subscribed.
Examples:
1.
Subscribe BkLight, Tasmota/BackyardLight/stat/POWER
And define a rule like:
Rule1 on event#BkLight=ON do ruletimer4 60 endon
2.
Subscribe DnTemp, Tasmota/RoomSensor1/stat/SENSOR, DS18B20.Temperature
Define a rule to deal with the MQTT message like {"Time":"2017-02-16T10:13:52", "DS18B20":{"Temperature":20.6}}
Rule1 ON EVENT#DnTemp>=21 DO ... ENDON
2019-02-24 03:33:09 +00:00
# define SUPPORT_MQTT_EVENT // Support trigger event with MQTT subscriptions (+3k5 code)
2018-04-13 16:42:11 +01:00
2018-02-07 16:50:02 +00:00
// -- Internal Analog input -----------------------
2017-03-14 17:03:25 +00:00
# define USE_ADC_VCC // Display Vcc in Power status. Disable for use as Analog input on selected devices
2018-02-07 16:50:02 +00:00
// -- One wire sensors ----------------------------
2017-12-01 14:59:53 +00:00
// WARNING: Select none for default one DS18B20 sensor or enable one of the following two options for multiple sensors
2017-12-05 16:46:26 +00:00
//#define USE_DS18x20_LEGACY // Optional for more than one DS18x20 sensors with dynamic scan using library OneWire (+1k5 code)
2018-10-26 16:13:17 +01:00
# define USE_DS18x20 // Optional for more than one DS18x20 sensors with id sort, single scan and read retry (+1k3 code)
// #define W1_PARASITE_POWER // If using USE_DS18x20 then optimize for parasite powered sensors
2018-12-26 20:10:47 +00:00
// #define DS18B20_INTERNAL_PULLUP // Use INPUT_PULLUP internal pullup resistors for single DS18B20
2017-01-28 13:41:01 +00:00
2017-12-27 13:10:55 +00:00
// -- I2C sensors ---------------------------------
2018-12-18 17:36:53 +00:00
# define USE_I2C // I2C using library wire (+10k code, 0k2 mem, 124 iram)
2018-08-18 17:11:22 +01:00
2018-01-05 11:26:19 +00:00
# ifdef USE_I2C
2018-07-17 11:51:55 +01:00
# define USE_SHT // Enable SHT1X sensor (+1k4 code)
# define USE_HTU // Enable HTU21/SI7013/SI7020/SI7021 sensor (I2C address 0x40) (+1k5 code)
2018-12-15 14:55:51 +00:00
# define USE_BMP // Enable BMP085/BMP180/BMP280/BME280 sensors (I2C addresses 0x76 and 0x77) (+4k4 code)
// #define USE_BME680 // Enable support for BME680 sensor using Bosch BME680 library (+4k code)
2018-07-17 11:51:55 +01:00
# define USE_BH1750 // Enable BH1750 sensor (I2C address 0x23 or 0x5C) (+0k5 code)
2018-10-26 16:13:17 +01:00
// #define USE_VEML6070 // Enable VEML6070 sensor (I2C addresses 0x38 and 0x39) (+1k5 code)
# define USE_VEML6070_RSET 270000 // VEML6070, Rset in Ohm used on PCB board, default 270K = 270000ohm, range for this sensor: 220K ... 1Meg
# define USE_VEML6070_SHOW_RAW // VEML6070, shows the raw value of UV-A
2018-07-17 11:51:55 +01:00
// #define USE_ADS1115 // Enable ADS1115 16 bit A/D converter (I2C address 0x48, 0x49, 0x4A or 0x4B) based on Adafruit ADS1x15 library (no library needed) (+0k7 code)
// #define USE_ADS1115_I2CDEV // Enable ADS1115 16 bit A/D converter (I2C address 0x48, 0x49, 0x4A or 0x4B) using library i2cdevlib-Core and i2cdevlib-ADS1115 (+2k code)
// #define USE_INA219 // Enable INA219 (I2C address 0x40, 0x41 0x44 or 0x45) Low voltage and current sensor (+1k code)
# define USE_SHT3X // Enable SHT3x (I2C address 0x44 or 0x45) or SHTC3 (I2C address 0x70) sensor (+0k7 code)
// #define USE_TSL2561 // Enable TSL2561 sensor (I2C address 0x29, 0x39 or 0x49) using library Joba_Tsl2561 (+2k3 code)
// #define USE_MGS // Enable Xadow and Grove Mutichannel Gas sensor using library Multichannel_Gas_Sensor (+10k code)
2018-02-18 17:39:28 +00:00
# define MGS_SENSOR_ADDR 0x04 // Default Mutichannel Gas sensor i2c address
2018-07-17 11:51:55 +01:00
# define USE_SGP30 // Enable SGP30 sensor (I2C address 0x58) (+1k1 code)
// #define USE_SI1145 // Enable SI1145/46/47 sensor (I2C address 0x60) (+1k code)
# define USE_LM75AD // Enable LM75AD sensor (I2C addresses 0x48 - 0x4F) (+0k5 code)
// #define USE_APDS9960 // Enable APDS9960 Proximity Sensor (I2C address 0x39). Disables SHT and VEML6070 (+4k7 code)
2018-10-26 16:13:17 +01:00
// #define USE_MCP230xx // Enable MCP23008/MCP23017 - Must define I2C Address in #define USE_MCP230xx_ADDR below - range 0x20 - 0x27 (+4k7 code)
// #define USE_MCP230xx_ADDR 0x20 // Enable MCP23008/MCP23017 I2C Address to use (Must be within range 0x20 through 0x27 - set according to your wired setup)
2018-08-27 07:12:33 +01:00
// #define USE_MCP230xx_OUTPUT // Enable MCP23008/MCP23017 OUTPUT support through sensor29 commands (+1k5 code)
2018-08-09 11:02:46 +01:00
// #define USE_MCP230xx_DISPLAYOUTPUT // Enable MCP23008/MCP23017 to display state of OUTPUT pins on Web UI (+0k2 code)
2018-10-26 16:13:17 +01:00
// #define USE_PCA9685 // Enable PCA9685 I2C HW PWM Driver - Must define I2C Address in #define USE_PCA9685_ADDR below - range 0x40 - 0x47 (+1k4 code)
// #define USE_PCA9685_ADDR 0x40 // Enable PCA9685 I2C Address to use (Must be within range 0x40 through 0x47 - set according to your wired setup)
// #define USE_PCA9685_FREQ 50 // Define default PWM frequency in Hz to be used (must be within 24 to 1526) - If other value is used, it will rever to 50Hz
2018-07-17 11:51:55 +01:00
// #define USE_MPR121 // Enable MPR121 controller (I2C addresses 0x5A, 0x5B, 0x5C and 0x5D) in input mode for touch buttons (+1k3 code)
2018-07-23 16:42:12 +01:00
// #define USE_CCS811 // Enable CCS811 sensor (I2C address 0x5A) (+2k2 code)
2018-12-15 14:55:51 +00:00
// #define USE_MPU6050 // Enable MPU6050 sensor (I2C address 0x68 AD0 low or 0x69 AD0 high) (+3K3 of code and 188 Bytes of RAM)
// #define USE_MPU6050_DMP // Enable in MPU6050 to use the DMP on the chip, should create better results (+8k6 of code)
2018-10-26 16:13:17 +01:00
// #define USE_DS3231 // Enable DS3231 external RTC in case no Wifi is avaliable. See docs in the source file (+1k2 code)
// #define USE_RTC_ADDR 0x68 // Default I2C address 0x68
2018-12-15 14:55:51 +00:00
// #define USE_MGC3130 // Enable MGC3130 Electric Field Effect Sensor (I2C address 0x42) (+2k7 code, 0k3 mem)
2019-01-24 10:21:16 +00:00
// #define USE_MAX44009 // Enable MAX44009 Ambient Light sensor (I2C addresses 0x4A and 0x4B) (+0k8 code)
2018-10-26 16:13:17 +01:00
// #define USE_DISPLAY // Add I2C Display Support (+2k code)
# define USE_DISPLAY_MODES1TO5 // Enable display mode 1 to 5 in addition to mode 0
# define USE_DISPLAY_LCD // [DisplayModel 1] Enable Lcd display (I2C addresses 0x27 and 0x3F) (+6k code)
# define USE_DISPLAY_SSD1306 // [DisplayModel 2] Enable SSD1306 Oled 128x64 display (I2C addresses 0x3C and 0x3D) (+16k code)
# define USE_DISPLAY_MATRIX // [DisplayModel 3] Enable 8x8 Matrix display (I2C adresseses see below) (+11k code)
# define MTX_ADDRESS1 0x71 // [DisplayAddress1] I2C address of first 8x8 matrix module
# define MTX_ADDRESS2 0x74 // [DisplayAddress2] I2C address of second 8x8 matrix module
# define MTX_ADDRESS3 0x75 // [DisplayAddress3] I2C address of third 8x8 matrix module
# define MTX_ADDRESS4 0x72 // [DisplayAddress4] I2C address of fourth 8x8 matrix module
# define MTX_ADDRESS5 0x73 // [DisplayAddress5] I2C address of fifth 8x8 matrix module
# define MTX_ADDRESS6 0x76 // [DisplayAddress6] I2C address of sixth 8x8 matrix module
# define MTX_ADDRESS7 0x00 // [DisplayAddress7] I2C address of seventh 8x8 matrix module
# define MTX_ADDRESS8 0x00 // [DisplayAddress8] I2C address of eigth 8x8 matrix module
2018-01-05 11:26:19 +00:00
# endif // USE_I2C
2018-04-05 14:26:16 +01:00
// -- SPI sensors ---------------------------------
2018-10-26 16:13:17 +01:00
//#define USE_SPI // Hardware SPI using GPIO12(MISO), GPIO13(MOSI) and GPIO14(CLK) in addition to two user selectable GPIOs(CS and DC)
2018-08-18 17:11:22 +01:00
2018-04-05 14:26:16 +01:00
# ifdef USE_SPI
2018-10-26 16:13:17 +01:00
# ifndef USE_DISPLAY
# define USE_DISPLAY // Add SPI Display support for 320x240 and 480x320 TFT
# endif
# define USE_DISPLAY_ILI9341 // [DisplayModel 4] Enable ILI9341 Tft 480x320 display (+19k code)
2018-12-15 14:55:51 +00:00
// #define USE_DISPLAY_EPAPER_29 // [DisplayModel 5] Enable e-paper 2.9 inch display (+19k code)
2018-04-05 14:26:16 +01:00
# endif // USE_SPI
2018-02-07 16:50:02 +00:00
// -- Serial sensors ------------------------------
2018-12-18 17:36:53 +00:00
# define USE_MHZ19 // Add support for MH-Z19 CO2 sensor (+2k code)
# define USE_SENSEAIR // Add support for SenseAir K30, K70 and S8 CO2 sensor (+2k3 code)
2017-12-27 13:10:55 +00:00
# define CO2_LOW 800 // Below this CO2 value show green light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1)
# define CO2_HIGH 1200 // Above this CO2 value show red light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1)
2018-12-18 17:36:53 +00:00
# define USE_PMS5003 // Add support for PMS5003 and PMS7003 particle concentration sensor (+1k3 code)
# define USE_NOVA_SDS // Add support for SDS011 and SDS021 particle concentration sensor (+0k7 code)
2018-10-26 16:13:17 +01:00
# define WORKING_PERIOD 5 // Working period of the SDS Sensor, Takes a reading every X Minutes
2018-03-20 13:31:11 +00:00
# define USE_SERIAL_BRIDGE // Add support for software Serial Bridge (+0k8 code)
2018-08-18 17:11:22 +01:00
//#define USE_SDM120 // Add support for Eastron SDM120-Modbus energy meter (+1k7 code)
2018-05-14 13:04:10 +01:00
# define SDM120_SPEED 9600 // SDM120-Modbus RS485 serial speed (default: 2400 baud)
2018-12-15 14:55:51 +00:00
# define USE_SDM220 // Add extra parameters for SDM220 (+0k1 code)
2018-08-18 17:11:22 +01:00
//#define USE_SDM630 // Add support for Eastron SDM630-Modbus energy meter (+2k code)
2018-05-16 09:07:41 +01:00
# define SDM630_SPEED 9600 // SDM630-Modbus RS485 serial speed (default: 9600 baud)
2018-10-26 16:13:17 +01:00
//#define USE_MP3_PLAYER // Use of the DFPlayer Mini MP3 Player RB-DFR-562 commands: play, volume and stop
# define MP3_VOLUME 10 // Set the startup volume on init, the range can be 0..30(max)
2018-12-18 17:36:53 +00:00
# define USE_TUYA_DIMMER // Add support for Tuya Serial Dimmer
2018-12-15 14:55:51 +00:00
# define TUYA_DIMMER_ID 0 // Default dimmer Id
2018-12-18 17:36:53 +00:00
# define USE_ARMTRONIX_DIMMERS // Add support for Armtronix Dimmers (+1k4 code)
# define USE_PS_16_DZ // Add support for PS-16-DZ Dimmer
//#define USE_AZ7798 // Add support for AZ-Instrument 7798 CO2 datalogger (+1k6 code)
2019-02-08 07:59:33 +00:00
//#define USE_PN532_HSU // Add support for PN532 using HSU (Serial) interface (+1k8 code, 140 bytes mem)
2019-02-08 17:26:02 +00:00
// #define USE_PN532_CAUSE_EVENTS // Cause event execution for PN532_UID= and PN532_DATA=[if defined] (+ 30 bytes code)
2019-02-08 07:59:33 +00:00
// #define USE_PN532_DATA_FUNCTION // Add sensor40 command support for erase, setting data block content (+1k7 code, 388 bytes mem)
// #define USE_PN532_DATA_RAW // Allow DATA block to be used by non-alpha-numberic data (+ 80 bytes code, 48 bytes ram)
2018-12-18 17:36:53 +00:00
2018-10-26 16:13:17 +01:00
// Power monitoring sensors -----------------------
2018-12-18 17:36:53 +00:00
# define USE_PZEM004T // Add support for PZEM004T Energy monitor (+2k code)
# define USE_PZEM_AC // Add support for PZEM014,016 Energy monitor (+1k1 code)
# define USE_PZEM_DC // Add support for PZEM003,017 Energy monitor (+1k1 code)
# define USE_MCP39F501 // Add support for MCP39F501 Energy monitor as used in Shelly 2 (+3k1 code)
2018-01-27 16:52:48 +00:00
2018-02-07 16:50:02 +00:00
// -- Low level interface devices -----------------
2019-01-01 12:45:44 +00:00
//#define USE_MAX31855 // Add support for MAX31855 K-Type thermocouple sensor using softSPI
2018-12-18 17:36:53 +00:00
# define USE_IR_REMOTE // Send IR remote commands using library IRremoteESP8266 and ArduinoJson (+4k3 code, 0k3 mem, 48 iram)
2018-12-15 14:55:51 +00:00
// #define USE_IR_HVAC // Support for HVAC (Toshiba, Mitsubishi and LG) system using IR (+3k5 code)
2018-12-18 17:36:53 +00:00
# define USE_IR_RECEIVE // Support for IR receiver (+7k2 code, 264 iram)
2018-12-15 14:55:51 +00:00
# define IR_RCV_BUFFER_SIZE 100 // Max number of packets allowed in capture buffer (default 100 (*2 bytes ram))
# define IR_RCV_TIMEOUT 15 // Number of milli-Seconds of no-more-data before we consider a message ended (default 15)
# define IR_RCV_MIN_UNKNOWN_SIZE 6 // Set the smallest sized "UNKNOWN" message packets we actually care about (default 6)
2017-02-14 13:27:08 +00:00
2018-12-18 17:36:53 +00:00
# define USE_WS2812 // WS2812 Led string using library NeoPixelBus (+5k code, +1k mem, 232 iram) - Disable by //
# define USE_WS2812_CTYPE NEO_GRB // WS2812 Color type (NEO_RGB, NEO_GRB, NEO_BRG, NEO_RBG, NEO_RGBW, NEO_GRBW)
2017-10-18 17:22:34 +01:00
// #define USE_WS2812_DMA // DMA supports only GPIO03 (= Serial RXD) (+1k mem). When USE_WS2812_DMA is enabled expect Exceptions on Pow
2017-01-28 13:41:01 +00:00
2018-12-18 17:36:53 +00:00
# define USE_ARILUX_RF // Add support for Arilux RF remote controller (+0k8 code, 252 iram (non 2.3.0))
2017-11-15 22:07:45 +00:00
2018-12-18 17:36:53 +00:00
# define USE_SR04 // Add support for HC-SR04 ultrasonic devices (+1k code)
2018-04-20 13:31:09 +01:00
2018-08-18 17:11:22 +01:00
//#define USE_TM1638 // Add support for TM1638 switches copying Switch1 .. Switch8 (+1k code)
2018-12-18 17:36:53 +00:00
# define USE_HX711 // Add support for HX711 load cell (+1k5 code)
2018-10-26 16:13:17 +01:00
// #define USE_HX711_GUI // Add optional web GUI to HX711 as scale (+1k8 code)
2018-06-28 16:40:37 +01:00
2018-07-14 14:35:56 +01:00
# define USE_RF_FLASH // Add support for flashing the EFM8BB1 chip on the Sonoff RF Bridge. C2CK must be connected to GPIO4, C2D to GPIO5 on the PCB (+3k code)
2018-06-04 17:10:38 +01:00
2018-10-26 16:13:17 +01:00
# define USE_TX20_WIND_SENSOR // Add support for La Crosse TX20 anemometer (+2k code)
# define USE_RC_SWITCH // Add support for RF transceiver using library RcSwitch (+2k7 code, 460 iram)
2018-12-15 14:55:51 +00:00
//#define USE_RF_SENSOR // Add support for RF sensor receiver (434MHz or 868MHz) (+0k8 code)
// #define USE_THEO_V2 // Add support for decoding Theo V2 sensors as documented on https://sidweb.nl using 434MHz RF sensor receiver (+1k4 code)
2018-12-16 13:28:33 +00:00
// #define USE_ALECTO_V2 // Add support for decoding Alecto V2 sensors like ACH2010, WS3000 and DKW2012 weather stations using 868MHz RF sensor receiver (+1k7 code)
2018-12-15 14:55:51 +00:00
2019-02-02 01:12:13 +00:00
# define USE_SM16716 // Add support for SM16716 RGB LED controller (+0k7 code)
2019-02-01 04:37:22 +00:00
2018-06-24 16:50:42 +01:00
/*********************************************************************************************\
* Debug features are only supported in development branch
\ * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
//#define USE_DEBUG_DRIVER // Use xdrv_99_debug.ino providing commands CpuChk, CfgXor, CfgDump, CfgPeek and CfgPoke
2018-04-23 10:37:46 +01:00
/*********************************************************************************************\
2018-08-31 13:47:49 +01:00
* Optional firmware configurations
* Select none or just one for optional features and sensors as configured in sonoff_post . h
* See RELEASENOTES . md for selected features
2017-03-05 14:07:30 +00:00
\ * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
2019-02-08 13:55:45 +00:00
//#define FIRMWARE_CLASSIC // Create sonoff-classic with initial configuration tools WPS, SmartConfig and WifiManager
//#define FIRMWARE_BASIC // Create sonoff-basic with no sensors
//#define FIRMWARE_SENSORS // Create sonoff-sensors with useful sensors enabled
//#define FIRMWARE_KNX_NO_EMULATION // Create sonoff-knx with KNX but without Emulation
//#define FIRMWARE_DISPLAYS // Create sonoff-display with display drivers enabled
//#define FIRMWARE_MINIMAL // Create sonoff-minimal as intermediate firmware for OTA-MAGIC
2017-03-05 14:07:30 +00:00
2017-01-28 13:41:01 +00:00
/*********************************************************************************************\
* No user configurable items below
\ * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
2017-03-21 15:17:28 +00:00
# if defined(USE_MQTT_TLS) && defined(USE_WEBSERVER)
# error "Select either USE_MQTT_TLS or USE_WEBSERVER as there is just not enough memory to play with"
# endif
2018-10-26 16:13:17 +01:00
# endif // _MY_USER_CONFIG_H_
