Tasmota/tasmota/xdrv_23_zigbee_A_impl.ino

1850 lines
68 KiB
Arduino
Raw Normal View History

/*
xdrv_23_zigbee.ino - zigbee support for Tasmota
2019-12-31 13:23:34 +00:00
Copyright (C) 2020 Theo Arends and Stephan Hadinger
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifdef USE_ZIGBEE
#define XDRV_23 23
const char kZbCommands[] PROGMEM = D_PRFX_ZB "|" // prefix
#ifdef USE_ZIGBEE_ZNP
D_CMND_ZIGBEEZNPSEND "|" D_CMND_ZIGBEEZNPRECEIVE "|"
#endif // USE_ZIGBEE_ZNP
#ifdef USE_ZIGBEE_EZSP
2020-07-10 19:15:12 +01:00
D_CMND_ZIGBEE_EZSP_SEND "|" D_CMND_ZIGBEE_EZSP_RECEIVE "|" D_CMND_ZIGBEE_EZSP_LISTEN "|"
#endif // USE_ZIGBEE_EZSP
D_CMND_ZIGBEE_PERMITJOIN "|"
D_CMND_ZIGBEE_STATUS "|" D_CMND_ZIGBEE_RESET "|" D_CMND_ZIGBEE_SEND "|" D_CMND_ZIGBEE_PROBE "|"
D_CMND_ZIGBEE_INFO "|" D_CMND_ZIGBEE_FORGET "|" D_CMND_ZIGBEE_SAVE "|" D_CMND_ZIGBEE_NAME "|"
2020-03-26 19:58:59 +00:00
D_CMND_ZIGBEE_BIND "|" D_CMND_ZIGBEE_UNBIND "|" D_CMND_ZIGBEE_PING "|" D_CMND_ZIGBEE_MODELID "|"
D_CMND_ZIGBEE_LIGHT "|" D_CMND_ZIGBEE_OCCUPANCY "|"
D_CMND_ZIGBEE_RESTORE "|" D_CMND_ZIGBEE_BIND_STATE "|" D_CMND_ZIGBEE_MAP "|" D_CMND_ZIGBEE_LEAVE "|"
D_CMND_ZIGBEE_CONFIG "|" D_CMND_ZIGBEE_DATA
2020-03-01 10:25:59 +00:00
;
void (* const ZigbeeCommand[])(void) PROGMEM = {
#ifdef USE_ZIGBEE_ZNP
&CmndZbZNPSend, &CmndZbZNPReceive,
#endif // USE_ZIGBEE_ZNP
#ifdef USE_ZIGBEE_EZSP
2020-07-10 19:15:12 +01:00
&CmndZbEZSPSend, &CmndZbEZSPReceive, &CmndZbEZSPListen,
#endif // USE_ZIGBEE_EZSP
&CmndZbPermitJoin,
&CmndZbStatus, &CmndZbReset, &CmndZbSend, &CmndZbProbe,
&CmndZbInfo, &CmndZbForget, &CmndZbSave, &CmndZbName,
2020-03-26 19:58:59 +00:00
&CmndZbBind, &CmndZbUnbind, &CmndZbPing, &CmndZbModelId,
&CmndZbLight, &CmndZbOccupancy,
&CmndZbRestore, &CmndZbBindState, &CmndZbMap, CmndZbLeave,
&CmndZbConfig, CmndZbData,
};
/********************************************************************************************/
// Initialize internal structures
void ZigbeeInit(void)
{
// #pragma GCC diagnostic push
// #pragma GCC diagnostic ignored "-Winvalid-offsetof"
// Serial.printf(">>> offset %d %d %d\n", Z_offset(Z_Data_Light, dimmer), Z_offset(Z_Data_Light, x), Z_offset(Z_Data_Thermo, temperature));
// #pragma GCC diagnostic pop
2020-05-17 17:33:42 +01:00
// Check if settings in Flash are set
if (PinUsed(GPIO_ZIGBEE_RX) && PinUsed(GPIO_ZIGBEE_TX)) {
if (0 == Settings.zb_channel) {
AddLog_P(LOG_LEVEL_INFO, PSTR(D_LOG_ZIGBEE "Randomizing Zigbee parameters, please check with 'ZbConfig'"));
uint64_t mac64 = 0; // stuff mac address into 64 bits
WiFi.macAddress((uint8_t*) &mac64);
2020-07-31 10:35:26 +01:00
uint32_t esp_id = ESP_getChipId();
#ifdef ESP8266
2020-07-31 10:37:12 +01:00
uint32_t flash_id = ESP.getFlashChipId();
2020-07-31 10:35:26 +01:00
#else // ESP32
uint32_t flash_id = 0;
#endif // ESP8266 or ESP32
uint16_t pan_id = (mac64 & 0x3FFF);
if (0x0000 == pan_id) { pan_id = 0x0001; } // avoid extreme values
if (0x3FFF == pan_id) { pan_id = 0x3FFE; } // avoid extreme values
Settings.zb_pan_id = pan_id;
Settings.zb_ext_panid = 0xCCCCCCCC00000000L | (mac64 & 0x00000000FFFFFFFFL);
Settings.zb_precfgkey_l = (mac64 << 32) | (esp_id << 16) | flash_id;
Settings.zb_precfgkey_h = (mac64 << 32) | (esp_id << 16) | flash_id;
Settings.zb_channel = USE_ZIGBEE_CHANNEL;
Settings.zb_txradio_dbm = USE_ZIGBEE_TXRADIO_DBM;
}
2020-10-10 15:19:37 +01:00
if (Settings.zb_txradio_dbm < 0) {
Settings.zb_txradio_dbm = -Settings.zb_txradio_dbm;
2020-10-10 19:42:48 +01:00
#ifdef USE_ZIGBEE_EZSP
2020-10-10 15:19:37 +01:00
EZ_reset_config = true; // force reconfigure of EZSP
2020-10-10 19:42:48 +01:00
#endif
2020-10-10 15:19:37 +01:00
SettingsSave(2);
}
#ifdef USE_ZIGBEE_EZSP
// Check the I2C EEprom
Wire.beginTransmission(USE_ZIGBEE_ZBBRIDGE_EEPROM);
uint8_t error = Wire.endTransmission();
if (0 == error) {
AddLog_P(LOG_LEVEL_INFO, PSTR(D_LOG_ZIGBEE "ZBBridge EEPROM found at address 0x%02X"), USE_ZIGBEE_ZBBRIDGE_EEPROM);
zigbee.eeprom_present = true;
}
#endif
}
2020-07-02 21:56:37 +01:00
// update commands with the current settings
2020-07-02 21:56:37 +01:00
#ifdef USE_ZIGBEE_ZNP
ZNP_UpdateConfig(Settings.zb_channel, Settings.zb_pan_id, Settings.zb_ext_panid, Settings.zb_precfgkey_l, Settings.zb_precfgkey_h);
#endif
#ifdef USE_ZIGBEE_EZSP
EZ_UpdateConfig(Settings.zb_channel, Settings.zb_pan_id, Settings.zb_ext_panid, Settings.zb_precfgkey_l, Settings.zb_precfgkey_h, Settings.zb_txradio_dbm);
#endif
2020-06-19 19:54:37 +01:00
ZigbeeInitSerial();
}
/*********************************************************************************************\
* Commands
\*********************************************************************************************/
#ifdef USE_ZIGBEE_ZNP
// Do a factory reset of the CC2530
const unsigned char ZIGBEE_FACTORY_RESET[] PROGMEM =
{ Z_SREQ | Z_SAPI, SAPI_WRITE_CONFIGURATION, CONF_STARTUP_OPTION, 0x01 /* len */, 0x01 /* STARTOPT_CLEAR_CONFIG */};
//"2605030101"; // Z_SREQ | Z_SAPI, SAPI_WRITE_CONFIGURATION, CONF_STARTUP_OPTION, 0x01 len, 0x01 STARTOPT_CLEAR_CONFIG
#endif // USE_ZIGBEE_ZNP
void CmndZbReset(void) {
if (ZigbeeSerial) {
switch (XdrvMailbox.payload) {
case 1:
#ifdef USE_ZIGBEE_ZNP
ZigbeeZNPSend(ZIGBEE_FACTORY_RESET, sizeof(ZIGBEE_FACTORY_RESET));
#endif // USE_ZIGBEE_ZNP
eraseZigbeeDevices();
2020-10-10 15:19:37 +01:00
case 2: // fall through
Settings.zb_txradio_dbm = - abs(Settings.zb_txradio_dbm);
2020-10-29 11:21:24 +00:00
TasmotaGlobal.restart_flag = 2;
2020-10-10 15:19:37 +01:00
#ifdef USE_ZIGBEE_ZNP
2020-03-16 17:55:58 +00:00
ResponseCmndChar_P(PSTR(D_JSON_ZIGBEE_CC2530 " " D_JSON_RESET_AND_RESTARTING));
2020-10-10 15:19:37 +01:00
#endif // USE_ZIGBEE_ZNP
#ifdef USE_ZIGBEE_EZSP
ResponseCmndChar_P(PSTR(D_JSON_ZIGBEE_EZSP " " D_JSON_RESET_AND_RESTARTING));
#endif // USE_ZIGBEE_EZSP
break;
default:
2020-10-10 15:19:37 +01:00
ResponseCmndChar_P(PSTR("1 or 2 to reset"));
}
}
}
/********************************************************************************************/
2020-04-22 15:07:52 +01:00
//
// High-level function
// Send a command specified as an HEX string for the workload.
// The target endpoint is computed if zero, i.e. sent to the first known endpoint of the device.
//
// Inputs:
// - shortaddr: 16-bits short address, or 0x0000 if group address
// - groupaddr: 16-bits group address, or 0x0000 if unicast using shortaddr
// - endpoint: 8-bits target endpoint (source is always 0x01), if 0x00, it will be guessed from ZbStatus information (basically the first endpoint of the device)
// - clusterSpecific: boolean, is the message general cluster or cluster specific, used to create the FC byte of ZCL
// - clusterIf: 16-bits cluster number
// - param: pointer to HEX string for payload, should not be nullptr
// Returns: None
//
void zigbeeZCLSendStr(uint16_t shortaddr, uint16_t groupaddr, uint8_t endpoint, bool clusterSpecific, uint16_t manuf,
uint16_t cluster, uint8_t cmd, const char *param) {
size_t size = param ? strlen(param) : 0;
SBuffer buf((size+2)/2); // actual bytes buffer for data
if (param) {
while (*param) {
uint8_t code = parseHex_P(&param, 2);
buf.add8(code);
}
}
2020-05-17 17:33:42 +01:00
if ((0 == endpoint) && (BAD_SHORTADDR != shortaddr)) {
2020-03-14 13:17:30 +00:00
// endpoint is not specified, let's try to find it from shortAddr, unless it's a group address
endpoint = zigbee_devices.findFirstEndpoint(shortaddr);
//AddLog_P(LOG_LEVEL_DEBUG, PSTR("ZbSend: guessing endpoint 0x%02X"), endpoint);
}
AddLog_P(LOG_LEVEL_DEBUG, PSTR("ZbSend: shortaddr 0x%04X, groupaddr 0x%04X, cluster 0x%04X, endpoint 0x%02X, cmd 0x%02X, data %s"),
2020-03-14 13:17:30 +00:00
shortaddr, groupaddr, cluster, endpoint, cmd, param);
2020-05-17 17:33:42 +01:00
if ((0 == endpoint) && (BAD_SHORTADDR != shortaddr)) { // endpoint null is ok for group address
AddLog_P(LOG_LEVEL_INFO, PSTR("ZbSend: unspecified endpoint"));
return;
}
// everything is good, we can send the command
2020-09-06 19:51:20 +01:00
uint8_t seq = zigbee_devices.getNextSeqNumber(shortaddr);
ZigbeeZCLSend_Raw(ZigbeeZCLSendMessage({
shortaddr,
groupaddr,
cluster /*cluster*/,
endpoint,
cmd,
manuf, /* manuf */
clusterSpecific /* not cluster specific */,
true /* response */,
2020-10-19 19:34:40 +01:00
false /* discover route */,
2020-09-06 19:51:20 +01:00
seq, /* zcl transaction id */
buf.getBuffer(), buf.len()
}));
// now set the timer, if any, to read back the state later
if (clusterSpecific) {
if (!Settings.flag5.zb_disable_autoquery) {
// read back attribute value unless it is disabled
sendHueUpdate(shortaddr, groupaddr, cluster, endpoint);
}
}
}
// Special encoding for multiplier:
// multiplier == 0: ignore
// multiplier == 1: ignore
// multiplier > 0: divide by the multiplier
// multiplier < 0: multiply by the -multiplier (positive)
2020-08-20 07:25:53 +01:00
void ZbApplyMultiplier(double &val_d, int8_t multiplier) {
if ((0 != multiplier) && (1 != multiplier)) {
if (multiplier > 0) { // inverse of decoding
val_d = val_d / multiplier;
} else {
val_d = val_d * (-multiplier);
}
}
}
2020-10-13 21:45:11 +01:00
//
// Write Tuya-Moes attribute
//
bool ZbTuyaWrite(SBuffer & buf, const Z_attribute & attr, uint8_t transid) {
double val_d = attr.getFloat();
const char * val_str = attr.getStr();
if (attr.key_is_str) { return false; } // couldn't find attr if so skip
if (attr.isNum() && (1 != attr.attr_multiplier)) {
ZbApplyMultiplier(val_d, attr.attr_multiplier);
}
buf.add8(0); // status
buf.add8(transid); // transid
buf.add16(attr.key.id.attr_id); // dp
buf.add8(0); // fn
int32_t res = encodeSingleAttribute(buf, val_d, val_str, attr.attr_type);
if (res < 0) {
AddLog_P(LOG_LEVEL_INFO, PSTR(D_LOG_ZIGBEE "Error for Tuya attribute type %04X/%04X '0x%02X'"), attr.key.id.cluster, attr.key.id.attr_id, attr.attr_type);
2020-10-13 21:45:11 +01:00
return false;
}
return true;
}
2020-09-14 21:06:19 +01:00
//
// Send Attribute Write, apply mutlipliers before
//
bool ZbAppendWriteBuf(SBuffer & buf, const Z_attribute & attr, bool prepend_status_ok) {
double val_d = attr.getFloat();
const char * val_str = attr.getStr();
2020-10-13 21:45:11 +01:00
if (attr.key_is_str) { return false; } // couldn't find attr if so skip
2020-09-14 21:06:19 +01:00
if (attr.isNum() && (1 != attr.attr_multiplier)) {
ZbApplyMultiplier(val_d, attr.attr_multiplier);
}
// push the value in the buffer
buf.add16(attr.key.id.attr_id); // prepend with attribute identifier
if (prepend_status_ok) {
buf.add8(Z_SUCCESS); // status OK = 0x00
}
buf.add8(attr.attr_type); // prepend with attribute type
int32_t res = encodeSingleAttribute(buf, val_d, val_str, attr.attr_type);
if (res < 0) {
// remove the attribute type we just added
// buf.setLen(buf.len() - (operation == ZCL_READ_ATTRIBUTES_RESPONSE ? 4 : 3));
AddLog_P(LOG_LEVEL_INFO, PSTR(D_LOG_ZIGBEE "Unsupported attribute type %04X/%04X '0x%02X'"), attr.key.id.cluster, attr.key.id.attr_id, attr.attr_type);
2020-09-14 21:06:19 +01:00
return false;
}
return true;
}
2020-10-13 21:45:11 +01:00
//
// Parse "Report", "Write", "Response" or "Config" attribute
// Operation is one of: ZCL_REPORT_ATTRIBUTES (0x0A), ZCL_WRITE_ATTRIBUTES (0x02) or ZCL_READ_ATTRIBUTES_RESPONSE (0x01)
2020-10-13 21:45:11 +01:00
//
void ZbSendReportWrite(class JsonParserToken val_pubwrite, class ZigbeeZCLSendMessage & packet) {
SBuffer buf(200); // buffer to store the binary output of attibutes
if (nullptr == XdrvMailbox.command) {
XdrvMailbox.command = (char*) ""; // prevent a crash when calling ReponseCmndChar and there was no previous command
}
// iterate on keys
for (auto key : val_pubwrite.getObject()) {
JsonParserToken value = key.getValue();
2020-09-14 21:06:19 +01:00
Z_attribute attr;
attr.setKeyName(key.getStr());
2020-09-14 21:06:19 +01:00
if (Z_parseAttributeKey(attr)) {
// Buffer ready, do some sanity checks
2020-10-13 21:45:11 +01:00
// all attributes must use the same cluster
if (0xFFFF == packet.cluster) {
packet.cluster = attr.key.id.cluster; // set the cluster for this packet
} else if (packet.cluster != attr.key.id.cluster) {
2020-09-14 21:06:19 +01:00
ResponseCmndChar_P(PSTR("No more than one cluster id per command"));
return;
}
2020-09-14 21:06:19 +01:00
} else {
if (attr.key_is_str) {
Response_P(PSTR("{\"%s\":\"%s'%s'\"}"), XdrvMailbox.command, PSTR("Unknown attribute "), key);
return;
}
if (Zunk == attr.attr_type) {
Response_P(PSTR("{\"%s\":\"%s'%s'\"}"), XdrvMailbox.command, PSTR("Unknown attribute type for attribute "), key);
return;
}
}
2020-10-13 21:45:11 +01:00
// copy value from input to attribute, in numerical or string format
if (value.isStr()) {
attr.setStr(value.getStr());
} else if (value.isNum()) {
attr.setFloat(value.getFloat());
}
2020-09-14 21:06:19 +01:00
double val_d = 0; // I try to avoid `double` but this type capture both float and (u)int32_t without prevision loss
const char* val_str = ""; // variant as string
////////////////////////////////////////////////////////////////////////////////
// Split encoding depending on message
2020-10-13 21:45:11 +01:00
if (packet.cmd != ZCL_CONFIGURE_REPORTING) {
if ((packet.cluster == 0XEF00) && (packet.cmd == ZCL_WRITE_ATTRIBUTES)) {
// special case of Tuya / Moes attributes
if (buf.len() > 0) {
AddLog_P(LOG_LEVEL_INFO, PSTR(D_LOG_ZIGBEE "Only 1 attribute allowed for Tuya"));
2020-10-13 21:45:11 +01:00
return;
}
packet.clusterSpecific = true;
packet.cmd = 0x00;
if (!ZbTuyaWrite(buf, attr, zigbee_devices.getNextSeqNumber(packet.shortaddr))) {
return; // error
}
} else if (!ZbAppendWriteBuf(buf, attr, packet.cmd == ZCL_READ_ATTRIBUTES_RESPONSE)) { // general case
2020-09-14 21:06:19 +01:00
return; // error
}
} else {
// ////////////////////////////////////////////////////////////////////////////////
// ZCL_CONFIGURE_REPORTING
if (!value.isObject()) {
ResponseCmndChar_P(PSTR("Config requires JSON objects"));
return;
}
JsonParserObject attr_config = value.getObject();
bool attr_direction = false;
uint32_t dir = attr_config.getUInt(PSTR("DirectionReceived"), 0);
if (dir) { attr_direction = true; }
// read MinInterval and MaxInterval, default to 0xFFFF if not specified
uint16_t attr_min_interval = attr_config.getUInt(PSTR("MinInterval"), 0xFFFF);
uint16_t attr_max_interval = attr_config.getUInt(PSTR("MaxInterval"), 0xFFFF);
// read ReportableChange
JsonParserToken val_attr_rc = attr_config[PSTR("ReportableChange")];
if (val_attr_rc) {
val_d = val_attr_rc.getFloat();
val_str = val_attr_rc.getStr();
2020-09-14 21:06:19 +01:00
ZbApplyMultiplier(val_d, attr.attr_multiplier);
}
// read TimeoutPeriod
uint16_t attr_timeout = attr_config.getUInt(PSTR("TimeoutPeriod"), 0x0000);
2020-09-14 21:06:19 +01:00
bool attr_discrete = Z_isDiscreteDataType(attr.attr_type);
// all fields are gathered, output the butes into the buffer, ZCL 2.5.7.1
// common bytes
buf.add8(attr_direction ? 0x01 : 0x00);
2020-09-14 21:06:19 +01:00
buf.add16(attr.key.id.attr_id);
if (attr_direction) {
buf.add16(attr_timeout);
} else {
2020-09-14 21:06:19 +01:00
buf.add8(attr.attr_type);
buf.add16(attr_min_interval);
buf.add16(attr_max_interval);
if (!attr_discrete) {
2020-09-14 21:06:19 +01:00
int32_t res = encodeSingleAttribute(buf, val_d, val_str, attr.attr_type);
if (res < 0) {
2020-09-14 21:06:19 +01:00
Response_P(PSTR("{\"%s\":\"%s'%s' 0x%02X\"}"), XdrvMailbox.command, PSTR("Unsupported attribute type "), key, attr.attr_type);
return;
}
}
}
}
}
// did we have any attribute?
if (0 == buf.len()) {
ResponseCmndChar_P(PSTR("No attribute in list"));
return;
}
// all good, send the packet
2020-10-13 21:45:11 +01:00
packet.transacId = zigbee_devices.getNextSeqNumber(packet.shortaddr);
packet.msg = buf.getBuffer();
packet.len = buf.len();
ZigbeeZCLSend_Raw(packet);
ResponseCmndDone();
}
// Parse the "Send" attribute and send the command
void ZbSendSend(class JsonParserToken val_cmd, uint16_t device, uint16_t groupaddr, uint16_t cluster, uint8_t endpoint, uint16_t manuf) {
uint8_t cmd = 0;
String cmd_str = ""; // the actual low-level command, either specified or computed
const char *cmd_s = ""; // pointer to payload string
bool clusterSpecific = true;
static char delim[] = ", "; // delimiters for parameters
// probe the type of the argument
// If JSON object, it's high level commands
// If String, it's a low level command
if (val_cmd.isObject()) {
// we have a high-level command
JsonParserObject cmd_obj = val_cmd.getObject();
int32_t cmd_size = cmd_obj.size();
if (cmd_size > 1) {
Response_P(PSTR("Only 1 command allowed (%d)"), cmd_size);
return;
} else if (1 == cmd_size) {
// We have exactly 1 command, parse it
JsonParserKey key = cmd_obj.getFirstElement();
JsonParserToken value = key.getValue();
uint32_t x = 0, y = 0, z = 0;
uint16_t cmd_var;
uint16_t local_cluster_id;
const __FlashStringHelper* tasmota_cmd = zigbeeFindCommand(key.getStr(), &local_cluster_id, &cmd_var);
if (tasmota_cmd) {
cmd_str = tasmota_cmd;
} else {
Response_P(PSTR("Unrecognized zigbee command: %s"), key.getStr());
return;
}
// check cluster
if (0xFFFF == cluster) {
cluster = local_cluster_id;
} else if (cluster != local_cluster_id) {
ResponseCmndChar_P(PSTR("No more than one cluster id per command"));
return;
}
// parse the JSON value, depending on its type fill in x,y,z
if (value.isNum()) {
x = value.getUInt(); // automatic conversion to 0/1
// if (value.is<bool>()) {
// // x = value.as<bool>() ? 1 : 0;
2020-10-10 16:00:37 +01:00
// } else if
// } else if (value.is<unsigned int>()) {
// x = value.as<unsigned int>();
} else {
// if non-bool or non-int, trying char*
const char *s_const = value.getStr(nullptr);
// const char *s_const = value.as<const char*>();
if (s_const != nullptr) {
char s[strlen(s_const)+1];
strcpy(s, s_const);
if ((nullptr != s) && (0x00 != *s)) { // ignore any null or empty string, could represent 'null' json value
char *sval = strtok(s, delim);
if (sval) {
x = ZigbeeAliasOrNumber(sval);
sval = strtok(nullptr, delim);
if (sval) {
y = ZigbeeAliasOrNumber(sval);
sval = strtok(nullptr, delim);
if (sval) {
z = ZigbeeAliasOrNumber(sval);
}
}
}
}
}
}
//AddLog_P(LOG_LEVEL_DEBUG, PSTR("ZbSend: command_template = %s"), cmd_str.c_str());
if (0xFF == cmd_var) { // if command number is a variable, replace it with x
cmd = x;
x = y; // and shift other variables
y = z;
} else {
cmd = cmd_var; // or simply copy the cmd number
}
cmd_str = zigbeeCmdAddParams(cmd_str.c_str(), x, y, z); // fill in parameters
//AddLog_P(LOG_LEVEL_DEBUG, PSTR("ZbSend: command_final = %s"), cmd_str.c_str());
cmd_s = cmd_str.c_str();
} else {
// we have zero command, pass through until last error for missing command
}
} else if (val_cmd.isStr()) {
// low-level command
// Now parse the string to extract cluster, command, and payload
// Parse 'cmd' in the form "AAAA_BB/CCCCCCCC" or "AAAA!BB/CCCCCCCC"
// where AA is the cluster number, BBBB the command number, CCCC... the payload
// First delimiter is '_' for a global command, or '!' for a cluster specific command
const char * data = val_cmd.getStr();
uint16_t local_cluster_id = parseHex(&data, 4);
// check cluster
if (0xFFFF == cluster) {
cluster = local_cluster_id;
} else if (cluster != local_cluster_id) {
ResponseCmndChar_P(PSTR("No more than one cluster id per command"));
return;
}
// delimiter
if (('_' == *data) || ('!' == *data)) {
if ('_' == *data) { clusterSpecific = false; }
data++;
} else {
ResponseCmndChar_P(PSTR("Wrong delimiter for payload"));
return;
}
// parse cmd number
cmd = parseHex(&data, 2);
// move to end of payload
// delimiter is optional
if ('/' == *data) { data++; } // skip delimiter
cmd_s = data;
} else {
// we have an unsupported command type, just ignore it and fallback to missing command
}
AddLog_P(LOG_LEVEL_DEBUG, PSTR("ZigbeeZCLSend device: 0x%04X, group: 0x%04X, endpoint:%d, cluster:0x%04X, cmd:0x%02X, send:\"%s\""),
device, groupaddr, endpoint, cluster, cmd, cmd_s);
zigbeeZCLSendStr(device, groupaddr, endpoint, clusterSpecific, manuf, cluster, cmd, cmd_s);
ResponseCmndDone();
}
// Parse the "Send" attribute and send the command
2020-10-13 21:45:11 +01:00
void ZbSendRead(JsonParserToken val_attr, ZigbeeZCLSendMessage & packet) {
// ZbSend {"Device":"0xF289","Cluster":0,"Endpoint":3,"Read":5}
// ZbSend {"Device":"0xF289","Cluster":"0x0000","Endpoint":"0x0003","Read":"0x0005"}
// ZbSend {"Device":"0xF289","Cluster":0,"Endpoint":3,"Read":[5,6,7,4]}
// ZbSend {"Device":"0xF289","Endpoint":3,"Read":{"ModelId":true}}
// ZbSend {"Device":"0xF289","Read":{"ModelId":true}}
// ZbSend {"Device":"0xF289","ReadConig":{"Power":true}}
// ZbSend {"Device":"0xF289","Cluster":6,"Endpoint":3,"ReadConfig":0}
// params
size_t attrs_len = 0;
uint8_t* attrs = nullptr; // empty string is valid
size_t attr_item_len = 2; // how many bytes per attribute, standard for "Read"
size_t attr_item_offset = 0; // how many bytes do we offset to store attribute
2020-10-13 21:45:11 +01:00
if (ZCL_READ_REPORTING_CONFIGURATION == packet.cmd) {
attr_item_len = 3;
attr_item_offset = 1;
}
if (val_attr.isArray()) {
2020-09-13 15:11:20 +01:00
// value is an array []
JsonParserArray attr_arr = val_attr.getArray();
attrs_len = attr_arr.size() * attr_item_len;
attrs = (uint8_t*) calloc(attrs_len, 1);
uint32_t i = 0;
for (auto value : attr_arr) {
uint16_t val = value.getUInt();
i += attr_item_offset;
attrs[i++] = val & 0xFF;
attrs[i++] = val >> 8;
i += attr_item_len - 2 - attr_item_offset; // normally 0
}
} else if (val_attr.isObject()) {
2020-09-13 15:11:20 +01:00
// value is an object {}
JsonParserObject attr_obj = val_attr.getObject();
attrs_len = attr_obj.size() * attr_item_len;
attrs = (uint8_t*) calloc(attrs_len, 1);
uint32_t actual_attr_len = 0;
// iterate on keys
for (auto key : attr_obj) {
JsonParserToken value = key.getValue();
bool found = false;
// scan attributes to find by name, and retrieve type
for (uint32_t i = 0; i < ARRAY_SIZE(Z_PostProcess); i++) {
const Z_AttributeConverter *converter = &Z_PostProcess[i];
uint16_t local_attr_id = pgm_read_word(&converter->attribute);
uint16_t local_cluster_id = CxToCluster(pgm_read_byte(&converter->cluster_short));
// uint8_t local_type_id = pgm_read_byte(&converter->type);
if ((pgm_read_word(&converter->name_offset)) && (0 == strcasecmp_P(key.getStr(), Z_strings + pgm_read_word(&converter->name_offset)))) {
// match name
// check if there is a conflict with cluster
// TODO
if (!(value.getBool()) && attr_item_offset) {
// If value is false (non-default) then set direction to 1 (for ReadConfig)
attrs[actual_attr_len] = 0x01;
}
actual_attr_len += attr_item_offset;
attrs[actual_attr_len++] = local_attr_id & 0xFF;
attrs[actual_attr_len++] = local_attr_id >> 8;
actual_attr_len += attr_item_len - 2 - attr_item_offset; // normally 0
found = true;
// check cluster
2020-10-13 21:45:11 +01:00
if (0xFFFF == packet.cluster) {
packet.cluster = local_cluster_id;
} else if (packet.cluster != local_cluster_id) {
ResponseCmndChar_P(PSTR("No more than one cluster id per command"));
if (attrs) { free(attrs); }
return;
}
break; // found, exit loop
}
}
if (!found) {
AddLog_P(LOG_LEVEL_INFO, PSTR("ZIG: Unknown attribute name (ignored): %s"), key);
}
}
attrs_len = actual_attr_len;
} else {
2020-09-13 15:11:20 +01:00
// value is a literal
2020-10-13 21:45:11 +01:00
if (0xFFFF != packet.cluster) {
uint16_t val = val_attr.getUInt();
2020-09-13 15:11:20 +01:00
attrs_len = attr_item_len;
attrs = (uint8_t*) calloc(attrs_len, 1);
attrs[0 + attr_item_offset] = val & 0xFF; // little endian
attrs[1 + attr_item_offset] = val >> 8;
}
}
if (attrs_len > 0) {
2020-10-13 21:45:11 +01:00
// all good, send the packet
packet.transacId = zigbee_devices.getNextSeqNumber(packet.shortaddr);
packet.msg = attrs;
packet.len = attrs_len;
ZigbeeZCLSend_Raw(packet);
ResponseCmndDone();
} else {
ResponseCmndChar_P(PSTR("Missing parameters"));
}
if (attrs) { free(attrs); }
}
//
// Command `ZbSend`
//
// Examples:
// ZbSend {"Device":"0x0000","Endpoint":1,"Write":{"0006/0000":0}}
// ZbSend {"Device":"0x0000","Endpoint":1,"Write":{"Power":0}}
// ZbSend {"Device":"0x0000","Endpoint":1,"Write":{"AqaraRotate":0}}
// ZbSend {"Device":"0x0000","Endpoint":1,"Write":{"AqaraRotate":12.5}}
// ZbSend {"Device":"0x0000","Endpoint":1,"Write":{"006/0000%39":12.5}}
// ZbSend {"Device":"0x0000","Endpoint":1,"Write":{"AnalogInApplicationType":1000000}}
// ZbSend {"Device":"0x0000","Endpoint":1,"Write":{"TimeZone":-1000000}}
// ZbSend {"Device":"0x0000","Endpoint":1,"Write":{"Manufacturer":"Tasmota","ModelId":"Tasmota Z2T Router"}}
void CmndZbSend(void) {
// ZbSend { "device":"0x1234", "endpoint":"0x03", "send":{"Power":1} }
// ZbSend { "device":"0x1234", "endpoint":"0x03", "send":{"Power":"3"} }
// ZbSend { "device":"0x1234", "endpoint":"0x03", "send":{"Power":"0xFF"} }
// ZbSend { "device":"0x1234", "endpoint":"0x03", "send":{"Power":null} }
// ZbSend { "device":"0x1234", "endpoint":"0x03", "send":{"Power":false} }
// ZbSend { "device":"0x1234", "endpoint":"0x03", "send":{"Power":true} }
// ZbSend { "device":"0x1234", "endpoint":"0x03", "send":{"Power":"true"} }
// ZbSend { "device":"0x1234", "endpoint":"0x03", "send":{"ShutterClose":null} }
// ZbSend { "device":"0x1234", "endpoint":"0x03", "send":{"Power":1} }
// ZbSend { "device":"0x1234", "endpoint":"0x03", "send":{"Color":"1,2"} }
// ZbSend { "device":"0x1234", "endpoint":"0x03", "send":{"Color":"0x1122,0xFFEE"} }
2020-03-16 17:55:58 +00:00
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
2020-09-23 18:38:24 +01:00
JsonParser parser(XdrvMailbox.data);
JsonParserObject root = parser.getRootObject();
if (!root) { ResponseCmndChar_P(PSTR(D_JSON_INVALID_JSON)); return; }
// params
uint16_t device = BAD_SHORTADDR; // BAD_SHORTADDR is broadcast, so considered invalid
uint16_t groupaddr = 0x0000; // group address valid only if device == BAD_SHORTADDR
uint16_t cluster = 0xFFFF; // no default
uint8_t endpoint = 0x00; // 0x00 is invalid for the dst endpoint
uint16_t manuf = 0x0000; // Manuf Id in ZCL frame
// parse "Device" and "Group"
JsonParserToken val_device = root[PSTR(D_CMND_ZIGBEE_DEVICE)];
if (val_device) {
2020-11-01 21:28:55 +00:00
device = zigbee_devices.parseDeviceFromName(val_device.getStr(), true).shortaddr;
2020-05-17 17:33:42 +01:00
if (BAD_SHORTADDR == device) { ResponseCmndChar_P(PSTR("Invalid parameter")); return; }
}
2020-05-17 17:33:42 +01:00
if (BAD_SHORTADDR == device) { // if not found, check if we have a group
JsonParserToken val_group = root[PSTR(D_CMND_ZIGBEE_GROUP)];
if (val_group) {
groupaddr = val_group.getUInt();
} else { // no device nor group
ResponseCmndChar_P(PSTR("Unknown device"));
return;
2020-03-14 13:17:30 +00:00
}
}
// from here, either device has a device shortaddr, or if BAD_SHORTADDR then use group address
// Note: groupaddr == 0 is valid
// read other parameters
cluster = root.getUInt(PSTR(D_CMND_ZIGBEE_CLUSTER), cluster);
endpoint = root.getUInt(PSTR(D_CMND_ZIGBEE_ENDPOINT), endpoint);
manuf = root.getUInt(PSTR(D_CMND_ZIGBEE_MANUF), manuf);
// infer endpoint
if (BAD_SHORTADDR == device) {
endpoint = 0xFF; // endpoint not used for group addresses, so use a dummy broadcast endpoint
} else if (0 == endpoint) { // if it was not already specified, try to guess it
endpoint = zigbee_devices.findFirstEndpoint(device);
AddLog_P(LOG_LEVEL_DEBUG, PSTR("ZIG: guessing endpoint %d"), endpoint);
}
if (0 == endpoint) { // after this, if it is still zero, then it's an error
ResponseCmndChar_P(PSTR("Missing endpoint"));
return;
}
// from here endpoint is valid and non-zero
// cluster may be already specified or 0xFFFF
2020-03-14 13:17:30 +00:00
JsonParserToken val_cmd = root[PSTR(D_CMND_ZIGBEE_SEND)];
JsonParserToken val_read = root[PSTR(D_CMND_ZIGBEE_READ)];
JsonParserToken val_write = root[PSTR(D_CMND_ZIGBEE_WRITE)];
JsonParserToken val_publish = root[PSTR(D_CMND_ZIGBEE_REPORT)];
JsonParserToken val_response = root[PSTR(D_CMND_ZIGBEE_RESPONSE)];
JsonParserToken val_read_config = root[PSTR(D_CMND_ZIGBEE_READ_CONFIG)];
JsonParserToken val_config = root[PSTR(D_CMND_ZIGBEE_CONFIG)];
uint32_t multi_cmd = ((bool)val_cmd) + ((bool)val_read) + ((bool)val_write) + ((bool)val_publish)
+ ((bool)val_response) + ((bool)val_read_config) + ((bool)val_config);
if (multi_cmd > 1) {
ResponseCmndChar_P(PSTR("Can only have one of: 'Send', 'Read', 'Write', 'Report', 'Reponse', 'ReadConfig' or 'Config'"));
return;
}
// from here we have one and only one command
2020-03-14 13:17:30 +00:00
2020-10-13 21:45:11 +01:00
// collate information in a ready to send packet
ZigbeeZCLSendMessage packet({
device,
groupaddr,
cluster /*cluster*/,
endpoint,
ZCL_READ_ATTRIBUTES,
manuf, /* manuf */
false /* not cluster specific */,
false /* no response */,
2020-10-19 19:34:40 +01:00
false /* discover route */,
2020-10-13 21:45:11 +01:00
0, /* zcl transaction id */
nullptr, 0
});
if (val_cmd) {
// "Send":{...commands...}
// we accept either a string or a JSON object
ZbSendSend(val_cmd, device, groupaddr, cluster, endpoint, manuf);
} else if (val_read) {
// "Read":{...attributes...}, "Read":attribute or "Read":[...attributes...]
// we accept eitehr a number, a string, an array of numbers/strings, or a JSON object
2020-10-13 21:45:11 +01:00
packet.cmd = ZCL_READ_ATTRIBUTES;
ZbSendRead(val_read, packet);
} else if (val_write) {
// only KSON object
if (!val_write.isObject()) {
ResponseCmndChar_P(PSTR("Missing parameters"));
return;
}
// "Write":{...attributes...}
2020-10-13 21:45:11 +01:00
packet.cmd = ZCL_WRITE_ATTRIBUTES;
ZbSendReportWrite(val_write, packet);
} else if (val_publish) {
// "Publish":{...attributes...}
// only KSON object
if (!val_publish.isObject()) {
ResponseCmndChar_P(PSTR("Missing parameters"));
return;
}
2020-10-13 21:45:11 +01:00
packet.cmd = ZCL_REPORT_ATTRIBUTES;
ZbSendReportWrite(val_publish, packet);
} else if (val_response) {
// "Report":{...attributes...}
// only KSON object
if (!val_response.isObject()) {
ResponseCmndChar_P(PSTR("Missing parameters"));
return;
}
2020-10-13 21:45:11 +01:00
packet.cmd = ZCL_READ_ATTRIBUTES_RESPONSE;
ZbSendReportWrite(val_response, packet);
} else if (val_read_config) {
// "ReadConfg":{...attributes...}, "ReadConfg":attribute or "ReadConfg":[...attributes...]
// we accept eitehr a number, a string, an array of numbers/strings, or a JSON object
2020-10-13 21:45:11 +01:00
packet.cmd = ZCL_READ_REPORTING_CONFIGURATION;
ZbSendRead(val_read_config, packet);
} else if (val_config) {
// "Config":{...attributes...}
// only JSON object
if (!val_config.isObject()) {
ResponseCmndChar_P(PSTR("Missing parameters"));
return;
}
2020-10-13 21:45:11 +01:00
packet.cmd = ZCL_CONFIGURE_REPORTING;
ZbSendReportWrite(val_config, packet);
} else {
Response_P(PSTR("Missing zigbee 'Send', 'Write', 'Report' or 'Response'"));
return;
}
}
//
// Command `ZbBind`
//
2020-03-26 19:58:59 +00:00
void ZbBindUnbind(bool unbind) { // false = bind, true = unbind
// ZbBind {"Device":"<device>", "Endpoint":<endpoint>, "Cluster":<cluster>, "ToDevice":"<to_device>", "ToEndpoint":<to_endpoint>, "ToGroup":<to_group> }
2020-03-26 19:58:59 +00:00
// ZbUnbind {"Device":"<device>", "Endpoint":<endpoint>, "Cluster":<cluster>, "ToDevice":"<to_device>", "ToEndpoint":<to_endpoint>, "ToGroup":<to_group> }
// local endpoint is always 1, IEEE addresses are calculated
2020-03-16 17:55:58 +00:00
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
2020-09-23 18:38:24 +01:00
JsonParser parser(XdrvMailbox.data);
JsonParserObject root = parser.getRootObject();
if (!root) { ResponseCmndChar_P(PSTR(D_JSON_INVALID_JSON)); return; }
// params
2020-05-17 17:33:42 +01:00
uint16_t dstDevice = BAD_SHORTADDR; // BAD_SHORTADDR is broadcast, so considered invalid
2020-03-01 10:25:59 +00:00
uint64_t dstLongAddr = 0;
uint8_t endpoint = 0x00; // 0x00 is invalid for the src endpoint
uint8_t toendpoint = 0x01; // default dest endpoint to 0x01
2020-03-01 10:25:59 +00:00
uint16_t toGroup = 0x0000; // group address
2020-11-01 21:28:55 +00:00
uint16_t cluster = 0; // cluster 0 is default
2020-03-01 10:25:59 +00:00
// Information about source device: "Device", "Endpoint", "Cluster"
// - the source endpoint must have a known IEEE address
2020-11-01 21:28:55 +00:00
const Z_Device & src_device = zigbee_devices.parseDeviceFromName(root.getStr(PSTR(D_CMND_ZIGBEE_DEVICE), nullptr), true);
if (!src_device.valid()) { ResponseCmndChar_P(PSTR("Unknown source device")); return; }
2020-03-01 10:25:59 +00:00
// check if IEEE address is known
2020-11-01 21:28:55 +00:00
uint64_t srcLongAddr = src_device.longaddr;
2020-03-16 17:55:58 +00:00
if (0 == srcLongAddr) { ResponseCmndChar_P(PSTR("Unknown source IEEE address")); return; }
2020-03-01 10:25:59 +00:00
// look for source endpoint
endpoint = root.getUInt(PSTR(D_CMND_ZIGBEE_ENDPOINT), endpoint);
2020-11-01 21:28:55 +00:00
if (0 == endpoint) { endpoint = zigbee_devices.findFirstEndpoint(src_device.shortaddr); }
2020-03-01 10:25:59 +00:00
// look for source cluster
JsonParserToken val_cluster = root[PSTR(D_CMND_ZIGBEE_CLUSTER)];
if (val_cluster) {
cluster = val_cluster.getUInt(cluster); // first convert as number
if (0 == cluster) {
zigbeeFindAttributeByName(val_cluster.getStr(), &cluster, nullptr, nullptr);
}
}
// Or Group Address - we don't need a dstEndpoint in this case
JsonParserToken to_group = root[PSTR("ToGroup")];
if (to_group) { toGroup = to_group.getUInt(toGroup); }
2020-03-01 10:25:59 +00:00
// Either Device address
// In this case the following parameters are mandatory
// - "ToDevice" and the device must have a known IEEE address
// - "ToEndpoint"
JsonParserToken dst_device = root[PSTR("ToDevice")];
// If no target is specified, we default to coordinator 0x0000
if ((!to_group) && (!dst_device)) {
dstDevice = 0x0000;
2020-11-01 21:28:55 +00:00
dstLongAddr = localIEEEAddr;
toendpoint = 1;
}
2020-11-01 21:28:55 +00:00
if (dst_device) {
const Z_Device & dstDevice = zigbee_devices.parseDeviceFromName(dst_device.getStr(nullptr), true);
if (!dstDevice.valid()) { ResponseCmndChar_P(PSTR("Unknown dest device")); return; }
dstLongAddr = dstDevice.longaddr;
}
2020-03-01 10:25:59 +00:00
2020-11-01 21:28:55 +00:00
if (!to_group) {
if (0 == dstLongAddr) { ResponseCmndChar_P(PSTR("Unknown dest IEEE address")); return; }
toendpoint = root.getUInt(PSTR("ToEndpoint"), toendpoint);
2020-03-01 10:25:59 +00:00
}
// make sure we don't have conflicting parameters
2020-11-01 21:28:55 +00:00
if (to_group && dst_device) { ResponseCmndChar_P(PSTR("Cannot have both \"ToDevice\" and \"ToGroup\"")); return; }
#ifdef USE_ZIGBEE_ZNP
2020-03-14 13:17:30 +00:00
SBuffer buf(34);
buf.add8(Z_SREQ | Z_ZDO);
2020-03-26 19:58:59 +00:00
if (unbind) {
buf.add8(ZDO_UNBIND_REQ);
} else {
buf.add8(ZDO_BIND_REQ);
}
2020-11-07 16:54:17 +00:00
buf.add16(src_device.shortaddr);
2020-03-01 10:25:59 +00:00
buf.add64(srcLongAddr);
buf.add8(endpoint);
buf.add16(cluster);
2020-11-01 21:28:55 +00:00
if (!to_group) {
2020-03-01 10:25:59 +00:00
buf.add8(Z_Addr_IEEEAddress); // DstAddrMode - 0x03 = ADDRESS_64_BIT
buf.add64(dstLongAddr);
buf.add8(toendpoint);
} else {
buf.add8(Z_Addr_Group); // DstAddrMode - 0x01 = GROUP_ADDRESS
buf.add16(toGroup);
}
ZigbeeZNPSend(buf.getBuffer(), buf.len());
#endif // USE_ZIGBEE_ZNP
#ifdef USE_ZIGBEE_EZSP
SBuffer buf(24);
2020-07-20 16:24:51 +01:00
// ZDO message payload (see Zigbee spec 2.4.3.2.2)
buf.add64(srcLongAddr);
buf.add8(endpoint);
buf.add16(cluster);
2020-11-01 21:28:55 +00:00
if (!to_group) {
buf.add8(Z_Addr_IEEEAddress); // DstAddrMode - 0x03 = ADDRESS_64_BIT
buf.add64(dstLongAddr);
buf.add8(toendpoint);
} else {
buf.add8(Z_Addr_Group); // DstAddrMode - 0x01 = GROUP_ADDRESS
buf.add16(toGroup);
}
2020-11-07 16:54:17 +00:00
EZ_SendZDO(src_device.shortaddr, unbind ? ZDO_UNBIND_REQ : ZDO_BIND_REQ, buf.buf(), buf.len());
#endif // USE_ZIGBEE_EZSP
ResponseCmndDone();
}
2020-03-26 19:58:59 +00:00
//
// Command ZbBind
//
void CmndZbBind(void) {
ZbBindUnbind(false);
}
//
// Command ZbBind
//
void CmndZbUnbind(void) {
ZbBindUnbind(true);
}
//
// ZbLeave - ask for a device to leave the network
//
void CmndZbLeave(void) {
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
uint16_t shortaddr = zigbee_devices.parseDeviceFromName(XdrvMailbox.data, true).shortaddr;
if (BAD_SHORTADDR == shortaddr) { ResponseCmndChar_P(PSTR("Unknown device")); return; }
#ifdef USE_ZIGBEE_ZNP
SBuffer buf(14);
buf.add8(Z_SREQ | Z_ZDO); // 25
buf.add8(ZDO_MGMT_LEAVE_REQ); // 34
buf.add16(shortaddr); // shortaddr
buf.add64(0); // remove self
buf.add8(0x00); // don't rejoin and don't remove children
ZigbeeZNPSend(buf.getBuffer(), buf.len());
#endif // USE_ZIGBEE_ZNP
#ifdef USE_ZIGBEE_EZSP
// ZDO message payload (see Zigbee spec 2.4.3.3.4)
SBuffer buf(10);
buf.add64(0); // remove self
buf.add8(0x00); // don't rejoin and don't remove children
EZ_SendZDO(shortaddr, ZDO_MGMT_LEAVE_REQ, buf.getBuffer(), buf.len());
#endif // USE_ZIGBEE_EZSP
ResponseCmndDone();
}
void CmndZbBindState_or_Map(uint16_t zdo_cmd) {
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
2020-11-01 21:28:55 +00:00
uint16_t shortaddr = zigbee_devices.parseDeviceFromName(XdrvMailbox.data, true).shortaddr;
2020-05-17 17:33:42 +01:00
if (BAD_SHORTADDR == shortaddr) { ResponseCmndChar_P(PSTR("Unknown device")); return; }
uint8_t index = XdrvMailbox.index - 1; // change default 1 to 0
#ifdef USE_ZIGBEE_ZNP
SBuffer buf(10);
buf.add8(Z_SREQ | Z_ZDO); // 25
buf.add8(zdo_cmd); // 33
buf.add16(shortaddr); // shortaddr
buf.add8(index); // StartIndex = 0
ZigbeeZNPSend(buf.getBuffer(), buf.len());
#endif // USE_ZIGBEE_ZNP
#ifdef USE_ZIGBEE_EZSP
// ZDO message payload (see Zigbee spec 2.4.3.3.4)
uint8_t buf[] = { index }; // index = 0
EZ_SendZDO(shortaddr, zdo_cmd, buf, sizeof(buf));
#endif // USE_ZIGBEE_EZSP
ResponseCmndDone();
}
//
// Command `ZbBindState`
// `ZbBindState<x>` as index if it does not fit. If default, `1` starts at the beginning
//
void CmndZbBindState(void) {
2020-10-29 11:50:02 +00:00
#ifdef USE_ZIGBEE_ZNP
CmndZbBindState_or_Map(ZDO_MGMT_BIND_REQ);
#endif // USE_ZIGBEE_ZNP
#ifdef USE_ZIGBEE_EZSP
CmndZbBindState_or_Map(ZDO_Mgmt_Bind_req);
2020-10-29 11:50:02 +00:00
#endif // USE_ZIGBEE_EZSP
}
//
// Command `ZbMap`
// `ZbMap<x>` as index if it does not fit. If default, `1` starts at the beginning
//
void CmndZbMap(void) {
2020-10-29 11:50:02 +00:00
#ifdef USE_ZIGBEE_ZNP
CmndZbBindState_or_Map(ZDO_MGMT_LQI_REQ);
#endif // USE_ZIGBEE_ZNP
#ifdef USE_ZIGBEE_EZSP
CmndZbBindState_or_Map(ZDO_Mgmt_Lqi_req);
2020-10-29 11:50:02 +00:00
#endif // USE_ZIGBEE_EZSP
}
// Probe a specific device to get its endpoints and supported clusters
void CmndZbProbe(void) {
CmndZbProbeOrPing(true);
}
//
// Common code for `ZbProbe` and `ZbPing`
//
void CmndZbProbeOrPing(boolean probe) {
2020-03-16 17:55:58 +00:00
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
2020-11-01 21:28:55 +00:00
uint16_t shortaddr = zigbee_devices.parseDeviceFromName(XdrvMailbox.data, true).shortaddr;
2020-05-17 17:33:42 +01:00
if (BAD_SHORTADDR == shortaddr) { ResponseCmndChar_P(PSTR("Unknown device")); return; }
// everything is good, we can send the command
Z_SendIEEEAddrReq(shortaddr);
if (probe) {
Z_SendActiveEpReq(shortaddr);
}
ResponseCmndDone();
}
// Ping a device, actually a simplified version of ZbProbe
void CmndZbPing(void) {
CmndZbProbeOrPing(false);
}
//
// Command `ZbName`
// Specify, read or erase a Friendly Name
//
void CmndZbName(void) {
// Syntax is:
// ZbName <device_id>,<friendlyname> - assign a friendly name
// ZbName <device_id> - display the current friendly name
// ZbName <device_id>, - remove friendly name
//
// Where <device_id> can be: short_addr, long_addr, device_index, friendly_name
2020-03-16 17:55:58 +00:00
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
// check if parameters contain a comma ','
char *p;
2020-11-12 18:38:21 +00:00
strtok_r(XdrvMailbox.data, ",", &p);
// parse first part, <device_id>
2020-11-01 21:28:55 +00:00
Z_Device & device = zigbee_devices.parseDeviceFromName(XdrvMailbox.data, false); // it's the only case where we create a new device
2020-11-01 18:00:07 +00:00
if (!device.valid()) { ResponseCmndChar_P(PSTR("Unknown device")); return; }
if (p == nullptr) {
2020-11-01 18:00:07 +00:00
const char * friendlyName = device.friendlyName;
Response_P(PSTR("{\"0x%04X\":{\"" D_JSON_ZIGBEE_NAME "\":\"%s\"}}"), device.shortaddr, friendlyName ? friendlyName : "");
} else {
2020-08-23 14:22:36 +01:00
if (strlen(p) > 32) { p[32] = 0x00; } // truncate to 32 chars max
2020-11-01 18:00:07 +00:00
device.setFriendlyName(p);
Response_P(PSTR("{\"0x%04X\":{\"" D_JSON_ZIGBEE_NAME "\":\"%s\"}}"), device.shortaddr, p);
}
}
//
// Command `ZbName`
2020-03-01 10:25:59 +00:00
// Specify, read or erase a ModelId, only for debug purposes
//
2020-03-01 10:25:59 +00:00
void CmndZbModelId(void) {
// Syntax is:
// ZbName <device_id>,<friendlyname> - assign a friendly name
// ZbName <device_id> - display the current friendly name
// ZbName <device_id>, - remove friendly name
2020-03-01 10:25:59 +00:00
//
// Where <device_id> can be: short_addr, long_addr, device_index, friendly_name
2020-03-16 17:55:58 +00:00
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
2020-03-01 10:25:59 +00:00
// check if parameters contain a comma ','
char *p;
2020-11-12 18:38:21 +00:00
strtok_r(XdrvMailbox.data, ",", &p);
2020-03-01 10:25:59 +00:00
// parse first part, <device_id>
2020-11-01 18:00:07 +00:00
Z_Device & device = zigbee_devices.parseDeviceFromName(XdrvMailbox.data, true); // in case of short_addr, it must be already registered
if (!device.valid()) { ResponseCmndChar_P(PSTR("Unknown device")); return; }
2020-03-01 10:25:59 +00:00
if (p == nullptr) {
2020-11-01 18:00:07 +00:00
const char * modelId = device.modelId;
Response_P(PSTR("{\"0x%04X\":{\"" D_JSON_ZIGBEE_MODELID "\":\"%s\"}}"), device.shortaddr, modelId ? modelId : "");
2020-03-01 10:25:59 +00:00
} else {
2020-11-01 18:00:07 +00:00
device.setModelId(p);
Response_P(PSTR("{\"0x%04X\":{\"" D_JSON_ZIGBEE_MODELID "\":\"%s\"}}"), device.shortaddr, p);
2020-03-01 10:25:59 +00:00
}
}
//
// Command `ZbLight`
2020-03-14 13:17:30 +00:00
// Specify, read or erase a Light type for Hue/Alexa integration
void CmndZbLight(void) {
// Syntax is:
// ZbLight <device_id>,<x> - assign a bulb type 0-5
// ZbLight <device_id> - display the current bulb type and status
//
// Where <device_id> can be: short_addr, long_addr, device_index, friendly_name
2020-03-16 17:55:58 +00:00
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
2020-03-14 13:17:30 +00:00
// check if parameters contain a comma ','
char *p;
2020-11-12 18:38:21 +00:00
strtok_r(XdrvMailbox.data, ", ", &p);
2020-03-14 13:17:30 +00:00
// parse first part, <device_id>
2020-11-01 18:00:07 +00:00
Z_Device & device = zigbee_devices.parseDeviceFromName(XdrvMailbox.data, true); // in case of short_addr, it must be already registered
if (!device.valid()) { ResponseCmndChar_P(PSTR("Unknown device")); return; }
2020-03-14 13:17:30 +00:00
if (p) {
int8_t bulbtype = strtol(p, nullptr, 10);
2020-03-23 07:25:01 +00:00
if (bulbtype > 5) { bulbtype = 5; }
if (bulbtype < -1) { bulbtype = -1; }
2020-11-01 18:00:07 +00:00
device.setLightChannels(bulbtype);
2020-03-14 13:17:30 +00:00
}
Z_attribute_list attr_list;
device.jsonLightState(attr_list);
device.jsonPublishAttrList(PSTR(D_PRFX_ZB D_CMND_ZIGBEE_LIGHT), attr_list); // publish as ZbReceived
2020-03-14 13:17:30 +00:00
ResponseCmndDone();
}
//
// Command `ZbOccupancy`
// Specify, read or erase the Occupancy detector configuration
void CmndZbOccupancy(void) {
// Syntax is:
// ZbOccupancy <device_id>,<x> - set the occupancy time-out
// ZbOccupancy <device_id> - display the configuration
//
// List of occupancy time-outs:
// 0xF = default (90 s)
// 0x0 = no time-out
// 0x1 = 15 s
// 0x2 = 30 s
// 0x3 = 45 s
// 0x4 = 60 s
// 0x5 = 75 s
// 0x6 = 90 s -- default
// 0x7 = 105 s
// 0x8 = 120 s
// Where <device_id> can be: short_addr, long_addr, device_index, friendly_name
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
// check if parameters contain a comma ','
char *p;
2020-11-12 18:38:21 +00:00
strtok_r(XdrvMailbox.data, ", ", &p);
// parse first part, <device_id>
2020-11-01 18:00:07 +00:00
Z_Device & device = zigbee_devices.parseDeviceFromName(XdrvMailbox.data, true); // in case of short_addr, it must be already registered
if (!device.valid()) { ResponseCmndChar_P(PSTR("Unknown device")); return; }
int8_t occupancy_time = -1;
if (p) {
Z_Data_PIR & pir = (Z_Data_PIR&) device.data.getByType(Z_Data_Type::Z_PIR);
occupancy_time = strtol(p, nullptr, 10);
pir.setTimeoutSeconds(occupancy_time);
zigbee_devices.dirty();
} else {
const Z_Data_PIR & pir_found = (const Z_Data_PIR&) device.data.find(Z_Data_Type::Z_PIR);
if (&pir_found != nullptr) {
occupancy_time = pir_found.getTimeoutSeconds();
}
}
Response_P(PSTR("{\"" D_PRFX_ZB D_CMND_ZIGBEE_OCCUPANCY "\":%d}"), occupancy_time);
MqttPublishPrefixTopicRulesProcess_P(RESULT_OR_STAT, PSTR(D_PRFX_ZB D_CMND_ZIGBEE_LIGHT));
ResponseCmndDone();
}
2020-03-14 13:17:30 +00:00
//
// Command `ZbForget`
// Remove an old Zigbee device from the list of known devices, use ZigbeeStatus to know all registered devices
//
void CmndZbForget(void) {
2020-03-16 17:55:58 +00:00
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
2020-11-01 18:00:07 +00:00
Z_Device & device = zigbee_devices.parseDeviceFromName(XdrvMailbox.data, true); // in case of short_addr, it must be already registered
if (!device.valid()) { ResponseCmndChar_P(PSTR("Unknown device")); return; }
// everything is good, we can send the command
2020-11-01 18:00:07 +00:00
if (zigbee_devices.removeDevice(device.shortaddr)) {
ResponseCmndDone();
} else {
2020-03-16 17:55:58 +00:00
ResponseCmndChar_P(PSTR("Unknown device"));
}
}
//
// Command `ZbInfo`
// Display all information known about a device, this equivalent to `2bStatus3` with a simpler JSON output
//
void CmndZbInfo(void) {
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
Z_Device & device = zigbee_devices.parseDeviceFromName(XdrvMailbox.data, true); // in case of short_addr, it must be already registered
if (!device.valid()) { ResponseCmndChar_P(PSTR("Unknown device")); return; }
// everything is good, we can send the command
Z_attribute_list attr_list;
device.jsonDumpSingleDevice(attr_list, 3, false); // don't add Device/Name
device.jsonPublishAttrList(PSTR(D_JSON_ZIGBEE_INFO), attr_list); // publish as ZbReceived
ResponseCmndDone();
}
//
// Command `ZbSave`
// Save Zigbee information to flash
//
void CmndZbSave(void) {
2020-03-16 17:55:58 +00:00
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
switch (XdrvMailbox.payload) {
case 2: // save only data
hibernateAllData();
break;
case -1: // dump configuration
loadZigbeeDevices(true); // dump only
break;
case -2: // dump data
dumpZigbeeDevicesData();
break;
default:
saveZigbeeDevices();
break;
}
ResponseCmndDone();
}
// Restore a device configuration previously exported via `ZbStatus2``
// Format:
// Either the entire `ZbStatus3` export, or an array or just the device configuration.
// If array, if can contain multiple devices
// ZbRestore {"ZbStatus3":[{"Device":"0x5ADF","Name":"Petite_Lampe","IEEEAddr":"0x90FD9FFFFE03B051","ModelId":"TRADFRI bulb E27 WS opal 980lm","Manufacturer":"IKEA of Sweden","Endpoints":["0x01","0xF2"]}]}
// ZbRestore [{"Device":"0x5ADF","Name":"Petite_Lampe","IEEEAddr":"0x90FD9FFFFE03B051","ModelId":"TRADFRI bulb E27 WS opal 980lm","Manufacturer":"IKEA of Sweden","Endpoints":["0x01","0xF2"]}]
// ZbRestore {"Device":"0x5ADF","Name":"Petite_Lampe","IEEEAddr":"0x90FD9FFFFE03B051","ModelId":"TRADFRI bulb E27 WS opal 980lm","Manufacturer":"IKEA of Sweden","Endpoints":["0x01","0xF2"]}
void CmndZbRestore(void) {
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
2020-09-23 18:38:24 +01:00
JsonParser parser(XdrvMailbox.data);
JsonParserToken root = parser.getRoot();
2020-09-23 18:52:34 +01:00
if (!parser || !(root.isObject() || root.isArray())) { ResponseCmndChar_P(PSTR(D_JSON_INVALID_JSON)); return; }
// Check is root contains `ZbStatus<x>` key, if so change the root
JsonParserToken zbstatus = root.getObject().findStartsWith(PSTR("ZbStatus"));
if (zbstatus) {
root = zbstatus;
}
// check if the root is an array
if (root.isArray()) {
JsonParserArray arr = JsonParserArray(root);
for (const auto elt : arr) {
// call restore on each item
if (elt.isObject()) {
int32_t res = zigbee_devices.deviceRestore(JsonParserObject(elt));
if (res < 0) {
ResponseCmndChar_P(PSTR("Restore failed"));
return;
}
}
}
} else if (root.isObject()) {
int32_t res = zigbee_devices.deviceRestore(JsonParserObject(root));
if (res < 0) {
ResponseCmndChar_P(PSTR("Restore failed"));
return;
}
// call restore on a single object
} else {
ResponseCmndChar_P(PSTR("Missing parameters"));
return;
}
ResponseCmndDone();
}
//
// Command `ZbPermitJoin`
// Allow or Deny pairing of new Zigbee devices
//
2020-03-14 13:17:30 +00:00
void CmndZbPermitJoin(void) {
2020-03-16 17:55:58 +00:00
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
2020-06-29 21:21:32 +01:00
uint32_t payload = XdrvMailbox.payload;
2020-03-14 13:17:30 +00:00
uint8_t duration = 60; // default 60s
2020-03-14 13:17:30 +00:00
if (payload <= 0) {
duration = 0;
}
2020-03-14 13:17:30 +00:00
2020-06-29 21:21:32 +01:00
// ZNP Version
#ifdef USE_ZIGBEE_ZNP
if (99 == payload) {
duration = 0xFF; // unlimited time
}
2020-03-14 13:17:30 +00:00
SBuffer buf(34);
buf.add8(Z_SREQ | Z_ZDO); // 25
buf.add8(ZDO_MGMT_PERMIT_JOIN_REQ); // 36
buf.add8(0x0F); // AddrMode
buf.add16(0xFFFC); // DstAddr
buf.add8(duration);
buf.add8(0x00); // TCSignificance
ZigbeeZNPSend(buf.getBuffer(), buf.len());
2020-06-29 21:21:32 +01:00
#endif // USE_ZIGBEE_ZNP
2020-03-14 13:17:30 +00:00
2020-06-29 21:21:32 +01:00
// EZSP VERSION
#ifdef USE_ZIGBEE_EZSP
if (99 == payload) {
ResponseCmndChar_P(PSTR("Unlimited time not supported")); return;
}
2020-06-29 21:21:32 +01:00
SBuffer buf(3);
buf.add16(EZSP_permitJoining);
buf.add8(duration);
2020-07-22 18:29:16 +01:00
ZigbeeEZSPSendCmd(buf.getBuffer(), buf.len());
// send ZDO_Mgmt_Permit_Joining_req to all routers
buf.setLen(0);
buf.add8(duration);
buf.add8(0x01); // TC_Significance - This field shall always have a value of 1, indicating a request to change the Trust Center policy. If a frame is received with a value of 0, it shall be treated as having a value of 1.
2020-07-22 18:29:16 +01:00
EZ_SendZDO(0xFFFC, ZDO_Mgmt_Permit_Joining_req, buf.buf(), buf.len());
// Set Timer after the end of the period, and reset a non-expired previous timer
if (duration > 0) {
// Log pairing mode enabled
Response_P(PSTR("{\"" D_JSON_ZIGBEE_STATE "\":{\"Status\":21,\"Message\":\"Pairing mode enabled\"}}"));
MqttPublishPrefixTopicRulesProcess_P(RESULT_OR_TELE, PSTR(D_JSON_ZIGBEE_STATE));
2020-10-19 19:34:40 +01:00
zigbee.permit_end_time = millis() + duration * 1000;
AddLog_P(LOG_LEVEL_INFO, "zigbee.permit_end_time = %d", zigbee.permit_end_time);
2020-10-19 19:34:40 +01:00
} else {
zigbee.permit_end_time = millis();
}
2020-06-29 21:21:32 +01:00
#endif // USE_ZIGBEE_EZSP
ResponseCmndDone();
}
2020-07-10 19:15:12 +01:00
#ifdef USE_ZIGBEE_EZSP
//
// `ZbListen`: add a multicast group to listen to
// Overcomes a current limitation that EZSP only shows messages from multicast groups it listens too
//
// Ex: `ZbListen 99`, `ZbListen2 100`
void CmndZbEZSPListen(void) {
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
2020-08-05 19:49:07 +01:00
int32_t index = XdrvMailbox.index; // 0 is reserved for group 0 (auto-config)
2020-07-10 19:15:12 +01:00
int32_t group = XdrvMailbox.payload;
if (group <= 0) {
group = 0;
} else if (group > 0xFFFF) {
group = 0xFFFF;
}
2020-07-20 16:24:51 +01:00
2020-07-10 19:15:12 +01:00
SBuffer buf(8);
buf.add16(EZSP_setMulticastTableEntry);
buf.add8(index);
buf.add16(group); // group
buf.add8(0x01); // endpoint
buf.add8(0x00); // network index
2020-07-22 18:29:16 +01:00
ZigbeeEZSPSendCmd(buf.getBuffer(), buf.len());
2020-07-10 19:15:12 +01:00
ResponseCmndDone();
}
2020-10-19 19:34:40 +01:00
void ZigbeeGlowPermitJoinLight(void) {
static const uint16_t cycle_time = 1000; // cycle up and down in 1000 ms
static const uint16_t half_cycle_time = cycle_time / 2; // cycle up and down in 1000 ms
if (zigbee.permit_end_time) {
uint16_t led_power = 0; // turn led off
// permit join is ongoing
if (TimeReached(zigbee.permit_end_time)) {
zigbee.permit_end_time = 0; // disable timer
Z_PermitJoinDisable();
} else {
uint32_t millis_to_go = millis() - zigbee.permit_end_time;
uint32_t sub_second = millis_to_go % cycle_time;
if (sub_second <= half_cycle_time) {
led_power = changeUIntScale(sub_second, 0, half_cycle_time, 0, 1023);
} else {
led_power = changeUIntScale(sub_second, half_cycle_time, cycle_time, 1023, 0);
}
led_power = ledGamma10_10(led_power);
}
// change the led state
uint32_t led_pin = Pin(GPIO_LEDLNK);
if (led_pin < 99) {
2020-10-30 11:29:48 +00:00
analogWrite(led_pin, TasmotaGlobal.ledlnk_inverted ? 1023 - led_power : led_power);
2020-10-19 19:34:40 +01:00
}
}
}
2020-07-10 19:15:12 +01:00
#endif // USE_ZIGBEE_EZSP
//
// Command `ZbStatus`
//
void CmndZbStatus(void) {
if (ZigbeeSerial) {
2020-03-16 17:55:58 +00:00
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
2020-11-01 18:00:07 +00:00
String dump;
2020-11-01 21:28:55 +00:00
Z_Device & device = zigbee_devices.parseDeviceFromName(XdrvMailbox.data, true);
if (XdrvMailbox.data_len > 0) {
2020-11-01 18:00:07 +00:00
if (!device.valid()) { ResponseCmndChar_P(PSTR("Unknown device")); return; }
dump = zigbee_devices.dumpDevice(XdrvMailbox.index, device);
} else {
if (XdrvMailbox.index >= 2) { ResponseCmndChar_P(PSTR("Unknown device")); return; }
dump = zigbee_devices.dumpDevice(XdrvMailbox.index, *(Z_Device*)nullptr);
}
2020-04-22 15:07:52 +01:00
Response_P(PSTR("{\"%s%d\":%s}"), XdrvMailbox.command, XdrvMailbox.index, dump.c_str());
}
}
//
// Command `ZbData`
//
void CmndZbData(void) {
if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
// check if parameters contain a comma ','
char *p;
2020-11-12 18:38:21 +00:00
strtok_r(XdrvMailbox.data, ",", &p);
// parse first part, <device_id>
Z_Device & device = zigbee_devices.parseDeviceFromName(XdrvMailbox.data, true); // in case of short_addr, it must be already registered
if (!device.valid()) { ResponseCmndChar_P(PSTR("Unknown device")); return; }
if (p) {
// set ZbData
const SBuffer buf = SBuffer::SBufferFromHex(p, strlen(p));
hydrateDeviceData(device, buf, 0, buf.len());
} else {
// non-JSON, export current data
// ZbData 0x1234
// ZbData Device_Name
hibernateDeviceData(device, true); // log
}
ResponseCmndDone();
}
//
// Command `ZbConfig`
//
void CmndZbConfig(void) {
// ZbConfig
// ZbConfig {"Channel":11,"PanID":"0x1A63","ExtPanID":"0xCCCCCCCCCCCCCCCC","KeyL":"0x0F0D0B0907050301L","KeyH":"0x0D0C0A0806040200L"}
uint8_t zb_channel = Settings.zb_channel;
uint16_t zb_pan_id = Settings.zb_pan_id;
uint64_t zb_ext_panid = Settings.zb_ext_panid;
uint64_t zb_precfgkey_l = Settings.zb_precfgkey_l;
uint64_t zb_precfgkey_h = Settings.zb_precfgkey_h;
2020-10-10 15:19:37 +01:00
int8_t zb_txradio_dbm = Settings.zb_txradio_dbm;
// if (zigbee.init_phase) { ResponseCmndChar_P(PSTR(D_ZIGBEE_NOT_STARTED)); return; }
2020-10-10 16:00:37 +01:00
RemoveSpace(XdrvMailbox.data);
if (strlen(XdrvMailbox.data) > 0) {
2020-09-23 18:38:24 +01:00
JsonParser parser(XdrvMailbox.data);
JsonParserObject root = parser.getRootObject();
if (!root) { ResponseCmndChar_P(PSTR(D_JSON_INVALID_JSON)); return; }
// Channel
zb_channel = root.getUInt(PSTR("Channel"), zb_channel);
zb_pan_id = root.getUInt(PSTR("PanID"), zb_pan_id);
zb_ext_panid = root.getULong(PSTR("ExtPanID"), zb_ext_panid);
zb_precfgkey_l = root.getULong(PSTR("KeyL"), zb_precfgkey_l);
zb_precfgkey_h = root.getULong(PSTR("KeyH"), zb_precfgkey_h);
2020-10-10 15:19:37 +01:00
zb_txradio_dbm = root.getInt(PSTR("TxRadio"), zb_txradio_dbm);
2020-04-11 18:01:39 +01:00
if (zb_channel < 11) { zb_channel = 11; }
if (zb_channel > 26) { zb_channel = 26; }
2020-09-14 21:06:19 +01:00
// if network key is zero, we generate a truly random key with a hardware generator from ESP
if ((0 == zb_precfgkey_l) && (0 == zb_precfgkey_h)) {
AddLog_P(LOG_LEVEL_INFO, PSTR(D_LOG_ZIGBEE "generating random Zigbee network key"));
2020-09-14 21:06:19 +01:00
zb_precfgkey_l = (uint64_t)HwRandom() << 32 | HwRandom();
zb_precfgkey_h = (uint64_t)HwRandom() << 32 | HwRandom();
}
// Check if a parameter was changed after all
if ( (zb_channel != Settings.zb_channel) ||
(zb_pan_id != Settings.zb_pan_id) ||
(zb_ext_panid != Settings.zb_ext_panid) ||
(zb_precfgkey_l != Settings.zb_precfgkey_l) ||
2020-07-02 21:56:37 +01:00
(zb_precfgkey_h != Settings.zb_precfgkey_h) ||
(zb_txradio_dbm != Settings.zb_txradio_dbm) ) {
Settings.zb_channel = zb_channel;
Settings.zb_pan_id = zb_pan_id;
Settings.zb_ext_panid = zb_ext_panid;
Settings.zb_precfgkey_l = zb_precfgkey_l;
Settings.zb_precfgkey_h = zb_precfgkey_h;
2020-07-02 21:56:37 +01:00
Settings.zb_txradio_dbm = zb_txradio_dbm;
2020-10-29 11:21:24 +00:00
TasmotaGlobal.restart_flag = 2; // save and reboot
}
}
// display the current or new configuration
char hex_ext_panid[20] = "0x";
Uint64toHex(zb_ext_panid, &hex_ext_panid[2], 64);
char hex_precfgkey_l[20] = "0x";
Uint64toHex(zb_precfgkey_l, &hex_precfgkey_l[2], 64);
char hex_precfgkey_h[20] = "0x";
Uint64toHex(zb_precfgkey_h, &hex_precfgkey_h[2], 64);
// {"ZbConfig":{"Channel":11,"PanID":"0x1A63","ExtPanID":"0xCCCCCCCCCCCCCCCC","KeyL":"0x0F0D0B0907050301L","KeyH":"0x0D0C0A0806040200L"}}
Response_P(PSTR("{\"" D_PRFX_ZB D_JSON_ZIGBEE_CONFIG "\":{"
"\"Channel\":%d"
",\"PanID\":\"0x%04X\""
",\"ExtPanID\":\"%s\""
",\"KeyL\":\"%s\""
",\"KeyH\":\"%s\""
2020-07-02 21:56:37 +01:00
",\"TxRadio\":%d"
"}}"),
zb_channel, zb_pan_id,
hex_ext_panid,
2020-07-02 21:56:37 +01:00
hex_precfgkey_l, hex_precfgkey_h,
zb_txradio_dbm);
}
2020-06-27 17:17:40 +01:00
/*********************************************************************************************\
* Presentation
\*********************************************************************************************/
2020-08-23 15:16:32 +01:00
extern "C" {
// comparator function used to sort Zigbee devices by alphabetical order (if friendlyname)
// then by shortaddr if they don't have friendlyname
2020-08-23 15:16:32 +01:00
int device_cmp(const void * a, const void * b) {
const Z_Device &dev_a = zigbee_devices.devicesAt(*(uint8_t*)a);
const Z_Device &dev_b = zigbee_devices.devicesAt(*(uint8_t*)b);
const char * fn_a = dev_a.friendlyName;
const char * fn_b = dev_b.friendlyName;
if (fn_a && fn_b) {
return strcasecmp(fn_a, fn_b);
} else if (!fn_a && !fn_b) {
return (int32_t)dev_a.shortaddr - (int32_t)dev_b.shortaddr;
} else {
if (fn_a) return -1;
else return 1;
2020-08-23 15:16:32 +01:00
}
}
// Convert seconds to a string representing days, hours or minutes present in the n-value.
// The string will contain the most coarse time only, rounded down (61m == 01h, 01h37m == 01h).
// Inputs:
// - n: uint32_t representing some number of seconds
// - result: a buffer of suitable size (7 bytes would represent the entire solution space
// for UINT32_MAX including the trailing null-byte, or "49710d")
// - result_len: A numeric value representing the total length of the result buffer
// Returns:
// - The number of characters that would have been written were result sufficiently large
// - negatve number on encoding error from snprintf
//
int convert_seconds_to_dhm(uint32_t n, char *result, size_t result_len){
char fmtstr[] = "%02dmhd"; // Don't want this in progmem, because we mutate it.
uint32_t conversions[3] = {24 * 3600, 3600, 60};
uint32_t value;
for(int i = 0; i < 3; ++i) {
value = n / conversions[i];
if(value > 0) {
fmtstr[4] = fmtstr[6-i];
break;
}
n = n % conversions[i];
}
// Null-terminate the string at the last "valid" index, removing any excess zero values.
fmtstr[5] = '\0';
return snprintf(result, result_len, fmtstr, value);
}
}
2020-06-27 17:17:40 +01:00
void ZigbeeShow(bool json)
{
if (json) {
return;
#ifdef USE_WEBSERVER
} else {
uint32_t zigbee_num = zigbee_devices.devicesSize();
if (!zigbee_num) { return; }
2020-08-23 15:16:32 +01:00
if (zigbee_num > 255) { zigbee_num = 255; }
WSContentSend_P(PSTR("</table>{t}")); // Terminate current two column table and open new table
WSContentSend_P(PSTR(
"<style>"
// Table CSS
".ztd td:not(:first-child){width:20px;font-size:70%%}"
".ztd td:last-child{width:45px}"
".ztd .bt{margin-right:10px;}" // Margin right should be half of the not-first width
2020-09-25 17:42:00 +01:00
".htr{line-height:20px}"
// Lighting
".bx{height:14px;width:14px;display:inline-block;border:1px solid currentColor;background-color:var(--cl,#fff)}"
// Signal Strength Indicator
".ssi{display:inline-flex;align-items:flex-end;height:15px;padding:0}"
".ssi i{width:3px;margin-right:1px;border-radius:3px;background-color:#eee}"
".ssi .b0{height:25%%}.ssi .b1{height:50%%}.ssi .b2{height:75%%}.ssi .b3{height:100%%}.o30{opacity:.3}"
"</style>"
));
2020-08-23 15:16:32 +01:00
// sort elements by name, then by id
uint8_t sorted_idx[zigbee_num];
for (uint32_t i = 0; i < zigbee_num; i++) {
sorted_idx[i] = i;
}
qsort(sorted_idx, zigbee_num, sizeof(sorted_idx[0]), device_cmp);
uint32_t now = Rtc.utc_time;
2020-06-27 17:17:40 +01:00
for (uint32_t i = 0; i < zigbee_num; i++) {
2020-08-23 15:16:32 +01:00
const Z_Device &device = zigbee_devices.devicesAt(sorted_idx[i]);
uint16_t shortaddr = device.shortaddr;
char *name = (char*) device.friendlyName;
char sdevice[33];
if (nullptr == name) {
snprintf_P(sdevice, sizeof(sdevice), PSTR(D_DEVICE " 0x%04X"), shortaddr);
name = sdevice;
}
char sbatt[64];
snprintf_P(sbatt, sizeof(sbatt), PSTR("&nbsp;"));
if (device.validBatteryPercent()) {
snprintf_P(sbatt, sizeof(sbatt),
PSTR("<i class=\"bt\" title=\"%d%%\" style=\"--bl:%dpx\"></i>"),
device.batterypercent, changeUIntScale(device.batterypercent, 0, 100, 0, 14)
);
}
uint32_t num_bars = 0;
char slqi[4];
slqi[0] = '-';
slqi[1] = '\0';
if (device.validLqi()){
num_bars = changeUIntScale(device.lqi, 0, 254, 0, 4);
snprintf_P(slqi, sizeof(slqi), PSTR("%d"), device.lqi);
2020-06-27 17:17:40 +01:00
}
WSContentSend_PD(PSTR(
2020-09-25 17:42:00 +01:00
"<tr class='ztd htr'>"
"<td><b title='0x%04X %s - %s'>%s</b></td>" // name
"<td>%s</td>" // sbatt (Battery Indicator)
"<td><div title='" D_LQI " %s' class='ssi'>" // slqi
), shortaddr,
device.modelId ? device.modelId : "",
device.manufacturerId ? device.manufacturerId : "",
name, sbatt, slqi);
if(device.validLqi()) {
for(uint32_t j = 0; j < 4; ++j) {
WSContentSend_PD(PSTR("<i class='b%d%s'></i>"), j, (num_bars < j) ? PSTR(" o30") : PSTR(""));
}
}
char dhm[16]; // len("&#x1F557;" + "49710d" + '\0') == 16
snprintf_P(dhm, sizeof(dhm), PSTR("&nbsp;"));
if(device.validLastSeen()){
snprintf_P(dhm, sizeof(dhm), PSTR("&#x1F557;"));
convert_seconds_to_dhm(now - device.last_seen, &dhm[9], 7);
}
WSContentSend_PD(PSTR(
"</div></td>" // Close LQI
"<td>%s{e}" // dhm (Last Seen)
), dhm );
// Sensors
const Z_Data_Thermo & thermo = device.data.find<Z_Data_Thermo>();
if (&thermo != nullptr) {
2020-10-28 20:40:58 +00:00
bool validTemp = thermo.validTemperature();
bool validTempTarget = thermo.validTempTarget();
bool validThSetpoint = thermo.validThSetpoint();
bool validHumidity = thermo.validHumidity();
bool validPressure = thermo.validPressure();
if (validTemp || validTempTarget || validThSetpoint || validHumidity || validPressure) {
WSContentSend_P(PSTR("<tr class='htr'><td colspan=\"4\">&#9478;"));
if (validTemp) {
char buf[12];
dtostrf(thermo.getTemperature() / 100.0f, 3, 1, buf);
WSContentSend_PD(PSTR(" &#x2600;&#xFE0F; %s°C"), buf);
}
if (validTempTarget) {
char buf[12];
dtostrf(thermo.getTempTarget() / 100.0f, 3, 1, buf);
WSContentSend_PD(PSTR(" &#127919; %s°C"), buf);
}
if (validThSetpoint) {
WSContentSend_PD(PSTR(" &#9881;&#65039; %d%%"), thermo.getThSetpoint());
}
if (validHumidity) {
WSContentSend_P(PSTR(" &#x1F4A7; %d%%"), (uint16_t)(thermo.getHumidity() / 100.0f + 0.5f));
}
if (validPressure) {
WSContentSend_P(PSTR(" &#x26C5; %d hPa"), thermo.getPressure());
}
2020-10-28 20:40:58 +00:00
WSContentSend_P(PSTR("{e}"));
}
2020-06-29 12:52:24 +01:00
}
2020-08-26 07:56:13 +01:00
// Light, switches and plugs
const Z_Data_OnOff & onoff = device.data.find<Z_Data_OnOff>();
bool onoff_display = (&onoff != nullptr) ? onoff.validPower() : false;
const Z_Data_Light & light = device.data.find<Z_Data_Light>();
bool light_display = (&light != nullptr) ? light.validDimmer() : false;
const Z_Data_Plug & plug = device.data.find<Z_Data_Plug>();
if (onoff_display || light_display || (&plug != nullptr)) {
int8_t channels = device.getLightChannels();
if (channels < 0) { channels = 5; } // if number of channel is unknown, display all known attributes
WSContentSend_P(PSTR("<tr class='htr'><td colspan=\"4\">&#9478;"));
if (onoff_display) {
WSContentSend_P(PSTR(" %s"), onoff.getPower() ? PSTR(D_ON) : PSTR(D_OFF));
2020-08-26 07:56:13 +01:00
}
if (&light != nullptr) {
if (light.validDimmer() && (channels >= 1)) {
WSContentSend_P(PSTR(" &#128261; %d%%"), changeUIntScale(light.getDimmer(),0,254,0,100));
}
if (light.validCT() && ((channels == 2) || (channels == 5))) {
uint32_t ct_k = (((1000000 / light.getCT()) + 25) / 50) * 50;
WSContentSend_P(PSTR(" <span title=\"CT %d\"><small>&#9898; </small>%dK</span>"), light.getCT(), ct_k);
}
if (light.validHue() && light.validSat() && (channels >= 3)) {
uint8_t r,g,b;
uint8_t sat = changeUIntScale(light.getSat(), 0, 254, 0, 255); // scale to 0..255
LightStateClass::HsToRgb(light.getHue(), sat, &r, &g, &b);
WSContentSend_P(PSTR(" <i class=\"bx\" style=\"--cl:#%02X%02X%02X\"></i>#%02X%02X%02X"), r,g,b,r,g,b);
} else if (light.validX() && light.validY() && (channels >= 3)) {
uint8_t r,g,b;
LightStateClass::XyToRgb(light.getX() / 65535.0f, light.getY() / 65535.0f, &r, &g, &b);
WSContentSend_P(PSTR(" <i class=\"bx\" style=\"--cl:#%02X%02X%02X\"></i> #%02X%02X%02X"), r,g,b,r,g,b);
}
2020-08-26 07:56:13 +01:00
}
if (&plug != nullptr) {
2020-10-28 20:40:58 +00:00
bool validMainsVoltage = plug.validMainsVoltage();
bool validMainsPower = plug.validMainsPower();
if (validMainsVoltage || validMainsPower) {
WSContentSend_P(PSTR(" &#9889; "));
if (validMainsVoltage) {
WSContentSend_P(PSTR(" %dV"), plug.getMainsVoltage());
}
if (validMainsPower) {
WSContentSend_P(PSTR(" %dW"), plug.getMainsPower());
}
}
}
WSContentSend_P(PSTR("{e}"));
2020-08-26 07:56:13 +01:00
}
2020-06-27 17:17:40 +01:00
}
WSContentSend_P(PSTR("</table>{t}")); // Terminate current multi column table and open new table
2020-06-27 17:17:40 +01:00
#endif
}
}
/*********************************************************************************************\
* Interface
\*********************************************************************************************/
bool Xdrv23(uint8_t function)
{
bool result = false;
if (zigbee.active) {
switch (function) {
case FUNC_EVERY_50_MSECOND:
if (!zigbee.init_phase) {
zigbee_devices.runTimer();
}
break;
case FUNC_LOOP:
#ifdef USE_ZIGBEE_EZSP
if (ZigbeeUploadXmodem()) {
return false;
}
#endif
2020-07-22 18:29:16 +01:00
if (ZigbeeSerial) {
ZigbeeInputLoop();
ZigbeeOutputLoop(); // send any outstanding data
2020-10-19 19:34:40 +01:00
#ifdef USE_ZIGBEE_EZSP
ZigbeeGlowPermitJoinLight();
#endif // USE_ZIGBEE_EZSP
2020-07-22 18:29:16 +01:00
}
if (zigbee.state_machine) {
ZigbeeStateMachine_Run();
}
break;
2020-06-27 17:17:40 +01:00
#ifdef USE_WEBSERVER
case FUNC_WEB_SENSOR:
ZigbeeShow(false);
break;
#ifdef USE_ZIGBEE_EZSP
// GUI xmodem
case FUNC_WEB_ADD_HANDLER:
2020-10-20 17:56:18 +01:00
WebServer_on(PSTR("/" WEB_HANDLE_ZIGBEE_XFER), HandleZigbeeXfer);
break;
#endif // USE_ZIGBEE_EZSP
2020-06-27 17:17:40 +01:00
#endif // USE_WEBSERVER
case FUNC_PRE_INIT:
ZigbeeInit();
break;
case FUNC_COMMAND:
result = DecodeCommand(kZbCommands, ZigbeeCommand);
break;
}
}
return result;
}
#endif // USE_ZIGBEE