* Add new setting windmeter_measure_intvl and update speed computation
* Ensure windmeter_measure_intvl is not below 1
* Keep same settings order in response messages and add better comments
* Add files via upload
Added ENS16x library enabling read-out of ENS160 and ENS161 sensor component (follow-up of CCS811 and iAQcore)
Added ENS210 library to read out ENS210 temperature & humidity sensor
* Add files via upload
Add air quality sensor readout for ENS160 and ENS161 checking two possible I2C addresses (follow up sensor for CCS811 and iAQcore)
Add temperature and humidity sensor readout checking two possible I2C addresses
* Update BUILDS.md
Add USE_ENS16x and USE_ENS210
* Update decode-status.py
Add USE_ENS16x and ENS210
* Update I2CDEVICES.md
Add USE_ENS16x and USE_ENS210
* Update my_user_config.h
Add USE_ENS16x and USE_ENS210
* Update support_features.ino
Add USE_ENS16x and USE_ENS210
* Update tasmota_configurations.h
Add USE_ENS16x and ENS210
* Update tasmota_configurations_ESP32.h
Add USE_ENS16x and USE_ENS210
* Update xsns_111_ens16x.ino
Corrected I2X number
* Update xsns_112_ens210.ino
Corrected I2C number
* Disable USE_ENS16x and USE_ENS210 by default
* Added code size information
* cut down in libs
* optimize tasmota side
* fix ens16x web display
* final fix on alternate addresses
* update code & RAM usage
---------
Co-authored-by: Barbudor <barbudor@barbudor.net>
* fix: don't reset the device when coming out of deep sleep
* fix: move debug log message to inside the device validation
* Update xsns_110_max17043.ino
* add: update global battery percentage when max17043 reports new value
* Added a passive mode in sen5x sensor for parasitic installations. This skips reset & initialization of sensor on startup and reduces the polling to every 10 seconds to not interfere with and confuse the other I2C master on the bus, e.g. Ike* Vindstyrka.
* Removed obsolete updateCount. Cleanup.
* add: update DEBUG_THERMOSTAT to only control the virtual switch
Also, debug output is still generated but end user can control this debug level 3
* add: debug output of main controller parameters when thermostat enabled
Also, add units for debug outputs added to make them more intelligible
* Update xdrv_39_thermostat.ino
* add: debug message when sensor is detected as not alive
fix: display thermostat number in debug messages
* add: log message prefix string for thermostat
* Update xdrv_39_thermostat.ino
fix: typos in comments
add: debug messages
* add: debug prefix for thermostat
* add: debug prefix added to output lines
* fix: comment typos and small grammatical changes for clarity
* add: debug prefix 'THE' added to debug output
* Restart MAX17043 from the scratch
* revert change
* Changed battery capacity in charge (capacity is the Ah value of the battery, this degrades over time when battery ages)
* merge
* Changing xsns_109 to 110
* fix nr
* removed old xsns109
* Update I2CDEVICES.md
* clean-up usage of Interface
* New LWT on deepsleep
To allow better integration into HA LWT topic will report details of sleep status:
16:54:04.388 MQT: hm/tele/ESP_3284D1/LWT =
{"Sleep":{"Time":"2023-07-17T16:55:03","Sleep":1689612844,"Wakeup":1689612903}}
* Revert LWT back to non JSON
Send DeelSleep on LWT
Send Deepsleep parameters on topic DeepSleep
* Setting default for batteryLevel
* Enable BatteryPercentSet
Changing the battery level e.g. by rule
* Added Battery % to status message
* added battery_level_percent
* Added battery % support in STATE message
* Enable setting battery level
101 is reserved for power-plug. No battery Level reported
* Setting default for battery Level
101 is reserved for power plug
0..100 normal battery values
* Revert back LWT to Offline
Removed "DeepSleep" LWT status until further decision is made. Current implementation is technical sufficient for HA to detect a battery powered device
* Added discovery message after deepsleep change
* Added discovery for battery and deepsleep
This change will allow mqtt messages simpler by allowing something like
`publish cmnd/ir-bridge/IRHVAC {"Power": "On"}`.
The simpler format is required for working with mqtt clients like
iotMQTTPanel or similar on android.
Limitations:
- Requires full message be sent at-least once. I work around this with
a `system#boot` rule
- Gets messy with multiple devices. I have only one AC per room, and
this doesn't doesn't interfere with other IR devices.
TODO:
- [ ] Change the build flag `INCREMENTAL_IRAC`to a `SetOption`
- [ ] Persist `irac_prev_state` across reboots.
- [ ] Support multiple devices.
tyler.li
Matteo Albinola
Theo Arends
s-hadinger
Christian Baars
Barbudor
Christoph Friese
Paul Blacknell
Jason2866
Andre H. Beckedorf
Vincent de Groot
stefanbode
Andrew Klaus
Subhash Chandra