5.6.1 20170818
* Change module list order in webpage
* Fix Sonoff T1 1CH and 2CH configuration (#751)
*
* 5.6.0 20170818
* Fix Sonoff Pow intermittent exception 0
* Change Sonoff Pow sending Domoticz telemetry data only
* Add Ai-Thinker RGBW led (AiLight) (experimental)
* Add NeoPixelBus library to Sonoff Led for Hue support
* Add user configurable GPIO4 and GPIO5 to module Sonoff Bridge
* Add Sonoff B1 RGBCW led support with command Color RRGGBBCCWW (#676)
* Add command CT 152..500 to Sonoff Led and Sonoff B1 to control Color
Temperature
* Add Cold-Warm slider to web page for Sonoff Led and Sonoff B1
* Add CT parameter to Hue
* Add Sonoff T1 support (#582)
* Add AnalogInput0 if configured as Analog Input to webpage (#697, #746)
* Add command SetOption14 0|1 to enable interlock mode (#719, #721)
* Fix Mitsubishi HVAC IR power controll (#740)
5.5.2i
* Fix Sonoff Pow intermittent exception 0
* Change Sonoff Pow sending Domoticz telemetry data only
* Add Sonoff B1 RGBCW led support with command Color RRGGBBCCWW (#676)
* Add command CT 152..500 to Sonoff Led and Sonoff B1 to control Color
Temperature
* Add Cold-Warm slider to web page for Sonoff Led and Sonoff B1
* Add CT parameter to Hue
* Add Ai-Thinker RGBW led (AiLight) (experimental)
* Add NeoPixelBus library to Sonoff Led for Hue support (saves 1k code
space)
* Add user configurable GPIO4 and GPIO5 to module Sonoff Bridge
* Fix Mitsubishi HVAC IR power controll (#740)
* Add Sonoff T1 support (#582)
5.5.0 20170730
* Reduce code space by removing the following commands as they are
replaced by SetOption alternatives:
* SaveState = SetOption0
* ButtonRestrict = SetOption1
* Units = SetOption2
* MQTT = SetOption3
* MQTTResponse = SetOption4
* TempUnit = SetOption8
* Smoothing WS2812 animation poll, invert fade speed and max allowed
wakeup time down to 3000 seconds
* Fix initial button press detection
* Add support for Sonoff RF Bridge 433 using command RfKey
* Fix regression from 5.0.7 by increasing message buffer size from 360
to 368 to accomodate 4 x DS18x20 sensors (#637)
* Add GroupTopic to Topic test when using ButtonTopic/SwitchTopic to
send either ON/OFF or TOGGLE (#642)
* Adjust HLW calibration limits to accomodate HuaFan device and add
commands HlwPSet, HlwUSet and HlwISet (#654)
5.4.0 20170725
* Fix command reset regression introduced in 5.2.0
* Increase polling from 0.1 second to 0.05 second
* Add multipress to all buttons
* Fix button 1 double press behaviour on multi relay devices
* Add support for Hua Fan Smart Socket (#479)
* Add support for Sonoff 4ch Pro (#565)
* Add command SetOption13 1 to allow immediate action on single button
press
* (disables multipress, hold and unrestricted commands) (#587)
5.3.0 20170715
* Major Hue rewrite which might introduce Alexa problems. If so,
initiate an issue
* Add support for Sonoff Led and BN-SZ01 Ceiling Led brightness control
to Hue
* Fix Sonoff Led Power, Dimmer and Color MQTT response (#176)
* Add commands Delay and Backlog to allow multiple commands at once
separated by ";" (#593)
* Use default flashmode DOUT to solve restart hangs on esp8285 chips
(#453, #598)
* Change Web console column width from 99 to 300 (#599)
5.2.4 20170703
* Removed flash mode update after selecting different module solving
esp8285 related problems
* Add device type flag to sonoff_template.ino
* Change Sonoff Led Wakeup and add support for Sonoff BN-SZ01 Led
5.1.1 20170517
* Allow command FullTopic in group mode
* Prepare for more use of RTC memory
* Add independant WS2812 led string power control (#386, #390)
* Add command Counter<x> to control up to four GPIO falling edge
interrupt counters or timers (#459)
* Add command CounterType<x> to select between pulse counting or pulse
timing
* Add command CounterDebounce to select global counter debounce time in
mSec
5.1.0 20170513
* Fix Offline/Removal of retained topic when FullTopic is changed
* Add FullTopic to MQTT Configuration and Information web page
* Adde license model GPLv3 (#188)
4.1.3 20170410
* Add user configuarble GPIO to module S20 Socket and Slampher
* Add support for Sonoff SC (#112)
* Set PWM frequency from 1000Hz to 910Hz as used on iTead Sonoff Led
firmware (#122)
* Set Sonoff Led unconfigured floating outputs to 0 to reduce exceptions
due to power supply instabilities (#122)
* Add Access Point Mac Address to Status 11 and Telemetry (#329)
* Fix DS18B20 negative temperature readings (#334)
4.1.0 20170325
* Change static IP addresses in user_config.h from list (using commas)
to string (using dots)
* Unify display result of commands Modules, Module and Gpios
* Rewrite Module selection web page to bring size down from 18651 to
4319 bytes (!) (#234, #240)
* Add basic support for (Lixada) H801 RGBWW controller (#252)
* Add command Prefix1 to Prefix3 to assign SUB_PREFIX, PUB_PREFIX and
PUB_PREFIX2 respectively (#255)
* Add static ip addresses to flash (#262)
* Add commands IpAddress, Gateway, Subnetmask and DnsServer to select
static ip addresses (#273)
4.0.7 20170319
* Increased Sonoff Led PWM frequency from 432 to 1000
* Fix possible watch dog reboot after changing module type on web page
* Fix reporting of GPIO usage from web page
* Fix Sonoff Led blank during firmware upgrade
* Fix Sonoff Led flicker and possible flash corruption by using latest
Arduino-esp8266 versions
* of pwm core files included in sonoff library (#211)
* Add PWM output control with commands PWM1 to PWM5 using user
selectable GPIOs (#211)
* Fix exceptions due to low values of commands HlwPCal (10000), HlwUCal
(1000) and HlwICal (2500) (#223)
* Add Switch state to sensor status (#227, #233)
* Add user configuarble GPIO to module Sonoff Touch (#228)
* Add define WEB_PORT to user_config.h to change default web server port
from 80 (#232)
* Fix failed Ota Firmware upgrade started from Web page (#235)
4.0.6 20170316
* Fix to better find device by Wifi hostname
* Fix compile error when some I2C devices are disabled
* Add (experimental) support for SHT1X emulating I2C (#97)
* Add ADC to ElectroDragon (#203)
* Add support for Sonoff Dev (#206)
4.0.5 20170314
* Add command Status 11 to show power status with Vcc if define
USE_ADC_VCC is enabled (default)
* Add ADC input to Sonoff SV and Wemos D1 mini - Needs recompile with
define USE_ADC_VCC disabled (#137)
* Add MQTT host:port to timeout message (#199)
4.0.5 20170314
* Add command Status 11 to show power status with Vcc if define
USE_ADC_VCC is enabled (default)
* Add ADC input to Sonoff SV and Wemos D1 mini - Needs recompile with
define USE_ADC_VCC disabled (#137)
* Add MQTT host:port to timeout message (#199)
4.0.4 20170312
* Add pulse timers for up to 4 relays (#106)
* Fix Sonoff Led power state when dimmer or color is 0 (#176)
* Add command NtpServer<x> to configure up to three NTP servers (#177)
* Delete module User Test as module Wemos D1 mini has same/more user
configurable GPIO (#178)
* Add more user configurable GPIO to module ElectroDragon (#183)
4.0.3 20170309
* Renamed Module NodeMCU to WeMos D1 mini
* Add GPIO1 as user option to some modules
* Add Buttons, Relays and Leds to user configurable options (#159)
* Add description on Module parameters web page to some well known GPIOs
(#107, #171)
3.9.22 20170228
* Update web console
* Fix Status 4 JSON message
* Add Exception info during restart if available
* Add osWatch service to detect loop hangs that might happen during
(OTA) upgrades
* Add WiOn support for relay and switch only (#82, #102)
* Allow for user specified relay count up to four in sonoff_template.h
(#109)
* Add support for HTU21 compatible I2C sensors SI7013, SI7020 and SI7021
(#118)
* Add NodeMCU or Wemos configuration option (#119)
3.9.21 20170224
* Add ajax to web root page and web console (#79)
* Add commands SwitchMode1..4 and enable user switches 2, 3 and 4 (#84,
#88)
* Fix MQTT upgrade when webserver is active
3.9.17 20170217
* Fix possible ArduinoJSON related memory fragmentation
* Changed console logging using less memory
* Add GPIO04 as user selectable for Sonoff Dual (#75)
3.9.16 20170214
* Update latching relay handler
* Add support for IR led using IRremoteESP8266 library (#59)
* Add Hue argument passing using ArduinoJSON library (#59)
3.9.15 20170213
* Change JSON float values from string to number according to
http://json.org (#56)
* Add support for exs latched relay module
https://ex-store.de/ESP8266-WiFi-Relay-V31 (#58)
* Add support for inverted relays
* Changed MAX_LOG_LINES from 70 to 60 to preserve memory
3.9.14 20170211
* Add False and True as alternatives for 0/Off and 1/On (#49)
* Fix Status10 JSON format (#52)
* Fix DS18x20 using OneWire library (#53)
3.9.13 20170210
* Add FlashChipSize to Status 4
* Removed redundant DHT2 option and code
* Add Sonoff SV GPIO pin 05 configuration (#40)
* Add configuration file backup and restore via web page
* Fix latency due to light_sleep mode even if sleep was set to zero
(#50)
3.9.13 20170210
* Add FlashChipSize to Status 4
* Removed redundant DHT2 option and code
* Add Sonoff SV GPIO pin 05 configuration (#40)
* Add configuration file backup and restore via web page
* Fix latency due to light_sleep mode even if sleep was set to zero
(#50)
3.9.11 20170204
* Fix command I2Cscan
* Fix not allowed spaces in Topic, ButtonTopic and SwitchTopic
* Make all TELEMETRY, STATUS and COMMAND message topics unique (#4)
* Advertise command topic to be used by iobroker (#299)
* Fix butten (non)detection if no GPIO_KEY1 is defined (#13)
* Change WeMo serialnumber from 7 decimal chars to 8 hexadecimal chars
(#18)
* Update web page with Build Date/Time, Emulation and mDNS Discovery and
Advertise information (#21)
arendst