Tasmota/CHANGELOG.md

Changelog

All notable changes to this project will be documented in this file.

[Unreleased] - Development

[14.3.0.4]

Added

• DALI command DaliGroupSliders 0..16 to show GUI group sliders with feedback disabling DaliLight

Breaking Changed

Changed

• AHT1X/AHT2X/AHT3X ready for virtual I2C
• SGP4X ready for virtual I2C
• SCD40 reduce logging levels
• SCD40 ready for virtual I2C

Fixed

• ESP32S3 UART output mode for Tx

Removed

[14.3.0.3] 20241031

Added

• Support for I2C over Serial

Changed

• ESP32 Platform from 2024.10.30 to 2024.11.30, Framework (Arduino Core) from v3.1.0.241023 to v3.1.0.241030 and IDF to 5.3.1.241024 (#22384)
• ESP32 LVGL library from v9.2.0 to v9.2.2 (#22385)
• Refactored i2c_enabled as array (#22387)

Fixed

• ESP32 Arduino Core IPv6 zones used by Matter (#22378)

[14.3.0.2] 20241030

Added

• DALI command DaliGear to set max found gear to speed up scan response
• DALI command DaliGroup to add gear to groups
• DALI command DaliTarget to set light control broadcast, group number or gear number
• Mitsubishi Electric HVAC Operation time for MiElHVAC (#22334)
• Mitsubishi Electric HVAC Outdoor Temperature for MiElHVAC (#22345)
• Mitsubishi Electric HVAC Compressor Frequency for MiElHVAC (#22347)
• SolaxX1 Meter mode (#22330)
• DALI inverted signal configuration using GPIO DALI RX_i/TX_i
• Support for Shelly DALI Dimmer Gen3 (See tips and template in file xdrv_75_dali.ino)
• HASPmota haspmota.get_pages() to get the sorted list of pages (#22358)
• Support for US AQI and EPA AQI in PMS5003x sensors (#22294)
• HLK-LD2410 Engineering mode (#21880)
• Support for HLK-LD2410S 24GHz smart wave motion sensor (#22253)
• Mitsubishi Electric HVAC Auto Clear Remote Temp for MiElHVAC (#22370)
• Command SetOption161 1 to disable web page slider updates by commands

Changed

• DALI renamed commands DaliCommission to DaliScan and DaliWeb to DaliLight
• DALI set Tasmota light control as default
• ESP32 Framework (Arduino Core) from v3.1.0.241015 to v3.1.0.241023 (#22351)
• Shutter optimized behavior to publish shutter data with sensor request (#22353)

Fixed

• Ethernet on -DFRAMEWORK_ARDUINO_ITEAD framework regression from v14.3.0 (#22367)
• Alexa Hue with multiple devices (#22383)

Removed

• DALI inverted signal configuration using compile time defines

[14.3.0.1] 20241022

Added

• BLE track devices with RPA (#22300)
• DALI support for short addresses and groups

Changed

• ESP32 platform update from 2024.09.30 to 2024.10.30 and Framework (Arduino Core) from v3.1.0.240926 to v3.1.0.241015 (#22299)
• HASPmota support for page delete and object updates (#22311)

Fixed

• EQ3 TRV firmware version 1.46 fails if the default true is used in subscribe on the notify characteristic (#22328)

[Released]

[14.3.0] 20241015

• Release Robert

[14.2.0.6] 20241015

Added

• Support for Sonoff SPM v1.3.0 (#13447)
• LVGL port colorwheel from LVGL 8 (#22244)
• HASPmota cpicker and msgbox (#22244)
• Support for DALI on ESP8266
• Command DaliWeb 1 to enable light control for DALI broadcast address
• Command DaliSend <address>|<address+256>,<command> to send command (address+256 is repeat) on DALI bus
• Command DaliQuery <address>|<address+256>,<command> to send command (address+256 is repeat) on DALI bus and wait up to DALI_TIMEOUT ms for response
• Berry Serial config to change parity on-the-fly for RS-485 (#22285)
• Mitsubishi Electric HVAC Heat/Dry/Cool Auto operation mode (#22216)
• Mitsubishi Electric HVAC Bridge to HomeBridge/Homekit locally (#22236)
• Mitsubishi Electric HVAC Air Direction Control (#22241)
• Mitsubishi Electric HVAC prohibit function (#22269)
• Mitsubishi Electric HVAC compressor map and operation power and energy (#22290)

Changed

• ESP32 platform update from 2024.09.10 to 2024.09.30 and Framework (Arduino Core) from v3.0.5 to v3.1.0.240926 (#22203)
• Berry improve persist dirty data handling (#22246)
• HASPmota delete instead of delete() (#22245)
• Command DaliDimmer range from 0..254 to 0..100

Fixed

• ESP32 Range Extender compile error with core 3.0.0 (#22205)
• HASPmota error when page '1' is not defined (#22220)
• ESP32-S3 uDisplay force cache writes to RGB display (#22222)
• ESP32 DALI compile error with core 3.x (#22214)
• DALI received data decoding
• ESP32 Ethernet using EthClockMode 3 (#22248)
• ESP32 disable SPI DMA for uDisplay (broken since esp-idf 5.3 (core 3.1.0)) (#22264)
• Sonoff WTS01 temperature sensor shows incorrect negative temperature (#19373)

Removed

• Berry Zigbee removed test code (#22263)

[14.2.0.5] 20240926

Added

• ESP8266 support for I2C CLK on GPIO16 (#22199)
• ESP8266 support for one-wire M1601 temperature sensor on DS18x20 GPIO (#21376)
• Support for BL0906 up to 6 channel energy monitor as used in Athom EM2/EM6 (#22167)

Changed

• ESP8266 platform update from 2024.06.00 to 2024.09.00 and Framework (Arduino Core) from v2.7.7 to v2.7.8 (#22199)

Fixed

• HASPmota broken changed event (#22194)

[14.2.0.4] 20240924

Added

• HX711 optional calibration precision option on command Sensor34 2 <weight in gram> <precision> where <precision> is 1 to 20 (#13983)
• Matter support for Zigbee Occupancy and Light 0/1/2 (OnOff / Dimmer / White Color Temperature) (#22110)
• KNX additional KnxTx functions and define KNX_USE_DPT9 (#22071)
• Support for I2C M5Unit (Mini)Scales using HX711 driver
• Berry virtual Energy driver (#22134)
• Support for RX8010 RTC as used in IOTTIMER (#21376)
• ESP8266 experimental support for second I2C bus
• Berry improve int64 constructor (#22172)
• MQTT warning if trying to connect without TLS on a port that normally uses TLS (#22175)

Changed

• Refactored I2C drivers HTU21, BH1750, SHT3x, iAQ and HYT
• Add command entered to command error and command unknown message
• ESP32 platform update from 2024.08.11 to 2024.09.10 and Framework (Arduino Core) from v3.0.4 to v3.0.5 (#22163)
• SCD30 Lowered I2C clock from 100k to 50k (#15438)
• Refactor and fix PID sensor (PID_USE_LOCAL_SENSOR) read race condition (#22162)

Fixed

• Shutter missing HOLD on shutterbutton (#22108)
• ModbusBridge request and response logic (#22075)
• Berry energy missing attributes (#22116)
• Zigbee flashing CC2562P with latest firmware (#22117)
• SML trx pin error (#22119)
• Shutter remaining issues on shutterinvert (#22120)
• Berry I2C to prepare M5Stack I2C STM32 based devices (#22143)
• Autoconf prevent 'init.bat' from stopping on empty lines (#22158)
• Compilation exception when metrics not found (#22170)
• ESP8266 Exception 3 on tasmota-minimal caused by unaligned PROGMEM (#22169)
• LVGL compilation of lv_menu (#22188)

[14.2.0.3] 20240908

Added

• Command SetOption69 1 to enable Serial Bridge inverted Receive (#22000)
• Support nexus protocol and calculation of separation limit to rc-switch library (#21886)
• Zigbee Koenkk firmware 20240710 for Sonoff Zigbee ZBPro (#22076)
• Berry Zigbee improvements to prepare Matter (#22083)
• Matter support for Zigbee Temperature, Humidity and Pressure sensors (#22084)
• SML multi TRX line (#22056)

Breaking Changed

• Berry make energy modules changes from #21887 backwards compatible (#22046)

Changed

• ESP32 platform update from 2024.08.10 to 2024.08.11 (#22021)
• ESP32 LVGL library from v9.1.0 to v9.2.0 (#22031)

Fixed

• Matter fixed UI bug when no endpoints configured (#22008)
• Zigbee extend timeout for MCU reboot from 5s to 10s (#22009)
• Matter fix when Rules are disabled (#22016)
• BearSSL panic on ESP8266 in rare conditions (#22017)
• Crash when calling TasmotaSerial destructor when initialized with incorrect arguments (#22036)
• LVGL Added OpenHASP icons to font montserrat-28 (#22048)
• Matter fail to report Shutter status if no shutter is configured in Tasmota (#22049)
• Matter fix Waterleak broken after Berry solidification optimisation #21885 (#22052)
• Berry avoid readbytes() from crashing when file is too large (#22057)
• Zigbee avoid disabling console serial on ESP32 and improved log messages (#22082)

Removed

• Berry remove reuse of methods for interface-like code reuse #21500 (#22055)

[14.2.0.2] 20240823

Changed

• Energy BL09xx command CurrentSet input changed from Ampere to milliAmpere
• GPIOViewer from v1.5.5 to v1.5.6

[14.2.0.1] 20240821

Added

• Energy Log level 4 message when (Calculated) Apparent Power is less than Active Power indicating wrong calibration (#20653)
• Energy command PowerSet 60,230 to calibrate both Current and Power with known resistive load of 60W at 230V using calibrated Voltage
• Energy command CurrentSet 60,230 to calibrate both Power and Current with known resistive load of 60W at 230V using calibrated Voltage

Changed

• Energy force Apparent Power equals Active Power when (Calculated) Apparent Power is less than Active Power (#20653)

Fixed

• Shutter timing registers overflow (#21966)
• PZEM continue energy monitoring when one phase fails (#21968)
• Energy calculation (#20653)

Removed

• ESP8266 Analog input support using energy driver as only one channel is available

[14.2.0] 20240814

• Release Rita

[14.1.0.4] 20240814

Added

• Support for Sonoff iFan04-H using template (#16402)
• Matter improve internal inspectfor superclasses (#21824)
• Matter support for split lights (SetOption68 1 and SetOption37 128) (#21834)
• Berry webserver_async (#21836)
• NeoPool command NPSetOption<x> to enabled/disable data validation/connection statistics (#21850)
• Analog GPIO ADC Input with AdcGpio<pin> <start_range>,<end_range>,<margin>,1 provide direct light control
• Analog GPIO ADC Voltage with AdcGpio<pin> <start_range>,<end_range>,<lowest_voltage>,<highest_voltage> provide energy monitoring with dc voltage
• Analog GPIO ADC Current with AdcGpio<pin> <start_range>,<end_range>,<lowest_current>,<highest_current> provide energy monitoring with dc voltage
• Berry new type "addr" to ctypes mapping (#21883)
• Berry file.savecode() (#21884)
• Berry solidify.nocompact() and reduce size of Matter UI (#21885)
• Berry zigbee.find() (#21889)
• Berry zigbee.started() (#21895)
• Command AdcGpio<gpio> <parameters> to better support ADC configuration
• Rule and Scripter xdrv sensor polling

Breaking Changed

• Berry energy module support for 8 phases and move to pseudo-arrays (#21887)

Changed

• Berry consolidated constants for solidified classes reduces Flash size (#2185)
• Berry updated precompiled Windows binary (#21858)
• Matter improve encoding of attributes to reduce flash size (#21864)
• ESP32 platform update from 2024.07.11 to 2024.08.10 (#21893)
• ESP32 Framework (Arduino Core) from v3.0.2 to v3.0.4 (#21893)
• Refactored Analog driver to better support multiple channels
• Zigbee loads device data early before MCU startup (#21917)
• Rule and Scripter sensor polling
• GUI name of Analog to ADC

Fixed

• Berry light.get for separate RGB/CT (#21818)
• Berry bytes setters and getters with negative offsets (#21835)
• Berry file.write() raises an exception on failure (ex: disk full) (#21849)
• Filesystem SD MMC free space display (#21869)

Removed

• Berry internal: remove class from closure to simplify code (#21839)

[14.1.0.3] 20240722

Added

• ESP32 support for power and energy limit checks, like MaxEnergy2 per phase (#21695)
• Berry tasmota.rtc("config_time") (#21698)
• Berry math.min() and math.max() (#21705)
• Berry FUNC_ANY_KEY event calling any_key() (#21708)
• Berry FUNC_BUTTON_MULTI_PRESSED event and make FUNC_BUTTON_PRESSED called only on state changes and once per second (#21711)
• Support for Sonoff POWCT Ring (#21131)
• NeoPool data validation and communication statistics default enabled for ESP32 only (#21721)
• FUNC_BUTTON_PRESSED now contains press_counter encoded in XdrvMailbox.command_code (#21724)
• Berry int64 added low32() and high32() methods, used in Matter (#21728)
• Matter support for 'Generic Switch' based on Tasmota Buttons (#21731)
• Berry cam module and img class (#21743)
• Skip MQTT response if command is prefixed with underscore (#21740)
• Skip MQTT response if commands are executed prefixed with Backlog2 (no delay) or Backlog3 (#21740)
• Support for Wooliis Hall Effect Coulometer or Battery capacity monitor (#21732)

Changed

• ESP32 support for energy margin checks, like MaxPower2 per phase (#21695)
• ESP32 TM1621 number overflow from "9999" to "12E3" (#21131)
• ESP32 platform update from 2024.06.11 to 2024.07.10 (#21745)
• ESP32 platform update from 2024.07.10 to 2024.07.11 (#21765)
• Berry simplified module persist (#21812)
• GPIOViewer from v1.5.4 to v1.5.5 (No functional change)

Fixed

• Berry bytes.resize() for large sizes (#21716)
• On universal display remove default backlight power if a single PWM channel is used for backlight. Regression from 14.0.0.1 (#21726)
• ESP32 I2S fixes (#21770)
• ESP32 Resistive Touch xpt for 2 spi buses (#21814)

[14.1.0.2] 20240627

Added

• Support for Sonoff WTS01 temperature sensor using SerialBridge in SSerialMode 3
• Berry classof extended to class methods (#21615)
• Extend command SetOption147 1 to disable publish of IRReceived MQTT messages (#21574)
• Matter support for Rain sensor (#21633)
• Matter internal debug option (#21634)
• Matter Fan support (virtual only) (#21637)
• Matter show event name in logs (#21649)
• Matter full support of events (#21698)

Changed

• SerialBridge command SSerialSend9 replaced by SSerialMode
• SML replace vars in descriptor and line (#21622)
• NeoPool using temperature as only frequently changing value for NPTeleperiod (#21628)
• NeoPool make compiler setting available by user_config_override.h (#21645)
• ESP32 MI32 improve parser (#21648)
• ESP8266 platform update from 2024.01.01 to 2024.06.00 (#21668)
• ESP8266 Framework (Arduino Core) from v2.7.6 to v2.7.7 (#21668)
• Matter refactor reading of multiple attributes to reduce memory pressure (#21675)
• ESP32 platform update from 2024.06.10 to 2024.06.11 (#21694)
• ESP32 Framework (Arduino Core) from v3.0.1 to v3.0.2 (#21694)

Fixed

• Matter interverted attributes 0xFFF9 and 0xFFFB (#21636)
• Matter CASE Sigma1 resumption mode for faster reconnection (#21644)
• Shutter MQTT on inverted shutter (#21663)
• Scripter TCP server (#21660)
• Matter TLV.U8 unsigned encoding (#21672)
• Matter resumption final ack (#21673)
• ESP32 allow use of UART0 with enabled USB_CDC_CONSOLE (#21496)

[14.1.0.1] 20240611

Added

• Berry solidification of bytes instances (#21558)
• Matter support for Air Quality sensors (#21559)
• Matter support for bridged Air Quality (#21597)
• HASPmota rounds to nearest int values passed as 'real' (#21599)
• Berry automatic rounding of float to int when calling C mapped functions (#21601)
• Berry add math.round (#21602)
• Support for QMP6988 temperature and pressure sensor

Changed

• Matter refactoring of bridged devices (#21575)
• ESP32 Core3 platform update from 2024.05.13 to 2024.06.10 (#21569)
• Optional MQTT_TELE_RETAIN to Energy Margins message replaced by SensorRetain
• Matter filter suffix automatically added for sensors (#21589)
• Display timing splash screen with display modes 1 to 5
• ESP32 MI32 refactoring, bugfixes, generic device scanning (#21603)
• Allow receive or send using SerialBridge

Fixed

• Berry input() returns empty string and does not crash (#21565)

[14.1.0] 20240603

• Release Rachel

[14.0.0.4] 20240603

Added

• SML FastExit for binary SML parsing (#21497)

Changed

• GPIOViewer from v1.5.3 to v1.5.4 (No functional change)
• TCP bridge increased baudrate selection (#21528)
• Berry coc parser keeps order of variables (#21542)

Fixed

• uDisplay Parallel display on Core3 (#21529)
• LVGL exception when using tjpegd (#21544)

Removed

• Deprecated code from drivers, USE_TTGO_WATCH and USE_M5STACK_CORE2 (#21533)

[14.0.0.3] 20240530

Changed

• ESP32 Core3 platform update from 2024.05.12 to 2024.05.13 (#21524)

Fixed

• ESP32 slow response when using UDP as in emulation (#21470)

[14.0.0.2] 20240529

Added

• Disabled watchdog for ESP32 and variants (#21509)

Changed

• Update Telegram CA (Go Daddy Root Certificate Authority - G2)

Fixed

• Telegram TLS fingerprint, remove CA validation (#21514)
• ESP32 I2S multiple fixes (#21511)

[14.0.0.1] 20240527

Added

• Enabled watchdog for ESP32 and variants (#21422)
• Optional command WebRun (as WebQuery extension) (#21364)
• Support for Knx dimmer and color (#21434)
• Support for Matter 1.3 Water leak detectors (#21456)
• Berry add reuse of methods for interface-like code reuse (#21500)

Changed

• ESP32 compiler option from target-align to no-target-align (#21407)
• On universal display remove default backlight power if a PWM channel is used for backlight
• Berry binary compiled with gcc (#21426)
• GPIOViewer from v1.5.2 to v1.5.3 (No functional change)
• Berry allow easy solidification of external Berry (#21430)
• ESP32 I2S audio improvements (#21433)
• Support W5500 SPI ethernet using four SPI GPIOs only without IRQ and RESET
• Berry change internal storage of parent class for methods (#21490)
• ESP32 Core3 platform update from 2024.05.11 to 2024.05.12 (#21493)

Fixed

• Domoticz re-subscribe on MQTT reconnect. Regression from v13.4.0.3 (#21281)
• Watchdog restart or freeze if displaytext is more than 128 characters (#21401)
• Avoid connection errors when switching to safeboot to upload OTA firmware (#21428)
• Berry Leds matrix alternate more and error about 'bri' attribute (#21431)
• Wrong timeout in WebQuery and webclient since Core3 (#21442)
• Webradio crash with invalid url (#21446)
• Zigbee crash when removing ZbName (#21449)
• ESP32 BLE fix scanning (#21451)
• I2S APLL not supported on all SOCs (#21483)
• UfsServe watchdog on large folder (#21486)
• Matter auto-fix IPv6 link-local zone id when network reconnects (#21494)
• SML compile error when median-filter is disabled (#21495)
• Hydreon RG15 malformed JSON string (#21508)

Removed

• Support of old insecure fingerprint algorithm. Deprecated since v8.4.0 (#21417)

[14.0.0] 20240515

• Release Rodney

[13.4.1.2] 20240515

Added

• ESP32 esp32_partition_app3904k_fs3392k partition scheme for 8MB ESP32S3 (#21241)
• TCP Serial bridge GPIO type TCP Tx En (#21269)
• Berry webserver.content_close() (#21276)
• ESP32 Compile option disabling PSRam check to avoid "blinking" of GPIO 16/17 at startup (#21282)
• HASPmota demo of Renaissance Watch for 480x480 displays (#21290)
• PlatformIO target reset (#21292)
• Support for AHT30 Temperature and Humidity Sensor (#19922)
• Berry wave file recorder (#21315)
• Command Publish3 to send binary data encoded as Hex, disabled in safeboot (21329)
• Support for compile time hostname with #define WIFI_DEFAULT_HOSTNAME (#21236)
• Berry after_teleperiod event matching FUNC_AFTER_TELEPERIOD (#21351)
• GPIOViewer pin mode support

Breaking Changed

• ESP32-C3 OTA binary name from tasmota32c3cdc.bin to tasmota32c3.bin with USB HWCDC and fallback to serial (#21212)
• ESP32-C6 OTA binary name from tasmota32c6cdc.bin to tasmota32c6.bin with USB HWCDC and fallback to serial (#21212)
• ESP32-S3 OTA binary name from tasmota32s3cdc.bin to tasmota32s3.bin with USB HWCDC and fallback to serial (#21212)

Changed

• uDisplay fast drawing on RGB displays (#21257)
• HDMI CEC synchronously sends messages (#21270)
• Refactor I2S (#21291)
• Command EthType option selection (#21317)
• Zigbee startup event triggered after plugins are loaded (#21320)
• Reduced safeboot size by 2.9KB (#21322)
• Internal macro APP_SLEEP to TASMOTA_SLEEP to specify default sleep in ms (#21324)
• ESP32 Core3 platform update from 2024.04.12 to 2024.05.10 (#21347)
• Refactor Tensorflow (#21327)
• Seriallog set to SERIAL_LOG_LEVEL at boot (#21363)
• TLS Letsencrypt replace R3 CA with long-term ISRG_Root_X1 CA, which works with R3 and R10-R14 (#21352)
• GPIOViewer from v1.5.0 to v1.5.2
• ESP32 Core3 platform update from 2024.05.10 to 2024.05.11 (#21381)
• Berry Leds uses native WS2812 driver by default (#21406)
• Command Pixels initiates a restart before activation due to changed NeoPixelBus library (#21406)

Fixed

• HASPmota align attribute and expand PNG cache (#21228)
• LVGL restore lv_palette functions (#21232)
• IPv6 support in safeboot (#21233)
• LVGL fix memory allocation of flush buffers (#21256)
• Neopool prevent possible multiple bus requests (#21267)
• Berry web_add_handler called before Webserver is initialized (#21272)
• Put back wifi IPv6 workaround (#21274)
• Async HDMI CEC (#21287)
• Berry math.inf, math.isinf() and fixed json output for inf and nan (#21304)
• Compilation of Ethernet when SPI drivers are disabled (#21321)
• Conflicting log_level definitions in NimBLE (#21337)
• Avoid unwanted OTA upgrade when safeboot starts for the first time (#21360)
• Matter broken NOCStruct types preventing pairing with HA (#21365)
• jpeg compile core3 (#21387)
• Berry gpio.dac_voltage() (#21403)

Removed

• LVGL disabled vector graphics (#21242)
• ESP32 IDF 4.4 based I2S code (#21188)
• Crash recorder from safeboot (#21332)

[13.4.1.1] 20240418

Added

• HASPmota dropdown_list and fixes (#21208)
• Support for SPL06_007 pressure and temperature sensor (#21185)

Breaking Changed

• ESP32 Ethernet Phy Type number for DM9051 from 4 to 10 (#21204)

Changed

• ESP32 Framework (Arduino Core) from v2.0.15 to v3.0.0 (#21180)
• ESP32 Core3 platform update from 2024.04.11 to 2024.04.12 (#21199)

Fixed

• HASPmota dropdown class "options" attribute (#21203)
• ESP8266 physical button/switch control when no rules activated (#21187)

Removed

• Support for ESP32 Arduino Core 2 (#21180)
• SSD1351 driver replaced with uDisplay (#21184)
• ST7789 driver replaced with uDisplay (#21184)

[13.4.0.4] 20240415

Added

• Command PowerLock to disable power control of selected outputs (#21081)
• Command Wifi 6 to enable 11ax on ESP32 Core3
• Berry flash.current_ota (#21097)

Breaking Changed

• Removed dedicated touch drivers in favour of Universal Touch driver (#21146)

Changed

• ESP32 refactored Wifi for ESP32 Core3 release (#21106)
• ESP32 Core3 platform update from 2024.02.10 to 2024.04.10 (#21114)
• ESP32 Core3 platform update from 2024.04.10 to 2024.04.11 (#21142)
• SGP4x Domoticz air quality value from raw to computed (#18880)
• ESP32 Framework (Arduino Core) from v2.0.14 to v2.0.15

Fixed

• NeoPool hydrolysis unit for Hidrolife, Bionet and Generic device (#21098)
• M5Core2 LoRa868 module receive exception
• Fade out on CCT bulb with SO92 1 (#21159)

Removed

• Unused #define MQTT_DATA_STRING support
• ILI9341 driver replaced with uDisplay (#21169)
• SSD1306 driver replaced with uDisplay (#21176)
• SSD1331 driver replaced with uDisplay (#21177)
• SSH1106 driver replaced with uDisplay (#21183)

[13.4.0.3] 20240402

Added

• Zigbee support for attributes of type uint48 used by energy monitoring (#20992)
• Support for single channel EU863-870 LoRaWanBridge (#17790)
• Support Azure iothub direct method (#21013)
• Added GPIO for SPI for Universal Touch Screen (#21025)
• Berry added close() to class serial (#21042)
• Support for Domoticz non-persistent DzIdx5 to DzIdx32 and disabling DOMOTICZ_OUT_TOPIC subscribe using command DzIdx0 0 (#21019)

Breaking Changed

• Berry loading .be file does not generated .bec anymore (#21075)

Changed

• ESP32 LVGL library from v9.0.0 to v9.1.0 (#21008)
• berry.exe (pre-compiled for Windows) updated to latest Berry patches (#21024)
• Some display.ini to utouch (#21029)
• ESP32 WiFi phy modes 11n and 11ax represented as HT20, HT40 and HE20 (#19350)
• KNX format of energy to match specifications (#21074)

Fixed

• BTHome, prep BLE5 (#20989)
• Scripter google char memory leak (#20995)
• HASPmota demo and robotocondensed fonts (#21014)
• Berry walrus bug when assigning to self (#21015)
• Too restrictive checksum checks in Lib_teleinfo (#21033)
• Color swap option for rgb displaytext (#21049)

Removed

• Berry print "a" syntax no longer supported (#21048)

[13.4.0.2] 20240318

Added

• Berry path.rename() (#20840)
• HASPmota support for spangroup (styled text) (#20852)
• HASPmota support for led (#20857)
• HASPmota improve arc and img (#20894)
• Berry string.startswith, string.endswith and %q format (#20909)
• LVGL lv.draw_label_dsc and lv_bar.get_indic_area (#20936)
• HASPmota support for scale, percentages (#20974)
• Support for ESP32-S3 120Mhz (#20973)
• Support for MCP23S08 (#20971)

Breaking Changed

• Drop support for old (insecure) fingerprint format (#20842)
• LVGL remove embedded typicons font (#20872)
• LVGL remove textarea and spinbox from binaries (#20916)

Changed

• LVGL optimize fonts and add icons (#20880)
• LVGL improved readability of montserrat-10 (#20900)
• HASPmota moved to a distinct library lv_haspmota (#20929)
• HASPmota solidify server-side (#20938)
• Refactor Platformio script post_esp32.py (#20966)

Fixed

• Berry bug when parsing ternary operator (#20839)
• HASPmota widgets line, btnmatrix, qrcode, bar, checkbox (#20881)
• Filesystem save of JSON settings data
• Berry fix walrus with member or index (#20939)
• TuyaV2 suppressed dimmer updates from MQTT (#20950)

[13.4.0.1] 20240229

Added

• Support for LoRa
• HASPmota p<x>b<y>.delete to delete an object (#20735)
• LVGL and HASPmota typicons font (#20742)
• HASPmota more attributes (#20744)
• QMC5883l check for overflow and scale reading (#20643)
• TasMesh support for LWT messages (#20392)
• Show calculated heat index if temperature and humidity is available with #define USE_HEAT_INDEX (#4771)
• Berry add explicit error log when memory allocation fails (#20807)
• Support for AMS5915/AMS6915 temperature and pressure sensors (#20814)
• IR support data larger than 64 bits (#20831)

Changed

• ESP32 Core3 SPI ethernet support for all models
• Berry class int64 made immutable (#20727)
• LVGL make lv_touch_3_buttons more responsive (#20728)
• ESP32 Core3 platform update from 2024.01.12 to 2024.02.10 (#20730)
• HASPmota fix and improve demo with pixel-perfect fonts (#20734)
• NeoPool webUI pH alarms (4 & 5) completed (#20743)
• Matter reduce memory usage when reading with wildcards (#20809)
• Prevent shutter MQTT broadcast with activated ShutterLock (#20827)

Fixed

• ESP32 PWM activity on unconfigured PWM GPIOs (#20732)
• Shutter inverted using internal commands (#20752)
• HASPmota PSRAM memory leak (#20818)
• Berry Memory leak in import re (#20823)

[13.4.0] 20240214

• Release Quinta

[13.3.0.5] 20240214

Added

• Internal support for persistent JSON settings using single file
• Command SetOption158 1 to disable publish of ModbusReceived MQTT messages (#20678)
• ESP32 Core3 support for SPI ethernet on DM9051, W5500 and KSZ8851
• Berry option to invert serial
• Command SetOption159 1 to enable counting on both rising and falling edge (#20712)

Breaking Changed

• ESP32 LVGL library from v8.3.11 to v9.0.0, some small breaking changes in C, none in HASPmota (#20659)

Changed

• Matter improve MtrInfo (#20686)
• Matter implement auto-attributes (#20694)
• GPIO Viewer user selection of assets website is https://ota.tasmota.com/tasmota/gpioviewer/gpio_viewer_13_4_0/ v2.0.8

Fixed

• Matter redirects for Advanced Matter configuration UI (#20690)
• LVGL9 restore missing layouts (#20701)

[13.3.0.4] 20240205

Added

• HASPmota support for min and max attribute in slider (#20582)
• ESP32-C3 support for GPIO11 (#18350)
• ESP32 support for Shelly Plus Add-On using DS18x20 or DHT11/AM2301/DHT21/DHT22/AM2302/AM2321/SI7021 on GPIO0/1 (#20580)
• ESP32 MI32 Legacy initial support for sensors using BTHOME packet format (#20625)
• Berry introspect.contains and bytes.addfloat (#20635)
• Matter add human readable names for TimeSync cluster (#20666)

Breaking Changed

• Matter aggregator relocated to endpoint 1 for Google compatibility, may break existing associations (#20654)

Changed

• Library OneWire-Stickbreaker by TasmotaOneWire supporting Shelly Plus Add-On (#20580)
• Refactored rules Subscribe using LList allowing full message size and enabled by default
• Refactored rules USE_EXPRESSION and SUPPORT_IF_STATEMENT replacing LinkedList with arrays and enabled by default
• ESP32 Core3 platform update from 2024.01.11 to 2024.01.12 (#20576)
• Utouch optimizations, rgb i2c init (#20596)
• GPIO Viewer update from 1.0.7 to 1.5.0
• Miel HVAC lower the minimum temperature to 10C (#20628)

Fixed

• Berry C mapping, raise an error if too many arguments are sent (#20604)
• Matter error when removing device from Google Home (#20665)
• Matter exception when fabrics is not initialized (#20667)

[13.3.0.3] 20240122

Added

• Berry debug.caller (#20470)
• GPIO Viewer user selection of assets website now defaults to https://ota.tasmota.com/tasmota|tasmota32/gpio_viewer/assets
• Support for HardwareSerial invert (#15461)
• SML support for IM350 (#20474)
• LVGL lv.str_arr (#20480)
• ESP32 MI BLE support for Xiaomi LYWSD02MMC (#20381)
• LVGL option to add lv.keyboard extra widget (#20496)
• GUI sensor separators (#20495)
• Command TimedPower<index> <milliseconds>[,ON|OFF|TOGGLE|BLINK] executes Power<index> [ON|OFF|TOGGLE|BLINK] and after executes Power<index> [OFF|ON|TOGGLE|BLINK_OFF]
• Berry solidification of strings longer than 255 bytes (#20529)
• Berry syntax coloring for Notepad++ by FransO (#20541)
• Berry/Zigbee web hook per device for customized status display (#20542)
• Zigbee ZbEmulation to selectively exclude some devices from Hue/Alexa emulation (#20552)

Changed

• ESP32 Core2 platform update from 2024.01.00 to 2024.01.01 (#20508)
• IP stack compatible with new Core3 IPv6 implementation (#20509)
• Command TimedPower from erasing all timers to showing remaining timers
• ESP8266 platform update from 2024.01.00 to 2024.01.01 (#20539)
• ESP8266 Framework (Arduino Core) from v2.7.5 to v2.7.6 (#20539)
• Refactored Pio filesystem download script (#20544)
• Command TimedPower refactored from String to LList

Fixed

• Scripter memory leak in >w x (#20473)
• ESP8266 GPIO Viewer exception 9 on reading Analog GPIO
• GPIO Viewer single instance
• Zigbee ramdom crash in main page (#20481)
• Web file upload response on upload error (#20340)
• ESP32 shutter exception 6 (divide by zero) on ShutterMode 4 (#20524)
• GPIOViewer exception 3
• Berry assignment to list with negative index (#20537)
• Matter support for Alexa (#20545)
• ESP8266 IPv6 support (#20539)
• ESP32 Audio for Core3, MP3Stream and Shine (#20540)
• ESP32 Core3 reset GPIOs 16/17 when PSRAM is not used (20547)

Removed

• Max number of 30 backlog entries

[13.3.0.2] 20240111

Added

• HASPmota type chart (#20372)
• Berry add support for tcpclientasync in tcpserver (#20401)
• Berry add tasmota.urlbecload(url:string) -> bool (#20412)
• GPIO Viewer to see realtime GPIO states. Enable with define USE_GPIO_VIEWER
• Berry gpio.read_pwm and gpio.read_pwm_resolution (#20414)
• Berry gpio.get_pin_type and gpio.ger_pin_type_index (#20415)
• Berry gpio.read_pwm and gpio.read_pwm_resolution (#20414)
• Berry GPIO viewer initial version using async webserver (#20416)
• Berry add string to bytes() (#20420)
• Berry button to dynamically load GPIO Viewer with Berry backend (#20424)
• Berry debug_panel.tapp to display real-time heap and wifi rssi (#20436)
• Berry webserver.header to read browser sent headers (#20447)
• Berry provide lightweight options for tasmota.wifi/eth/memory/rtc (#20448)
• Berry tasmota.webcolor (#20454)
• Support for pipsolar inverter (#20408)

Changed

• Renamed button "Consoles" to "Tools"
• ESP32 platform update from 2023.12.00 to 2024.01.00 (#20445)
• Header Host is now collected by Webserver (#20446)
• Webcam tweaks (#20451)
• ESP8266 platform update from 2023.04.00 to 2024.01.00 (#20467)
• ESP8266 Framework (Arduino Core) from v2.7.4.9 to v2.7.5 (#20467)

Fixed

• ESP32 Zigbee Aqara attributes (#20452)

[13.3.0.1] 20240101

Added

• Support for Sonoff Basic R4 Magic Switch (#20247)
• Support for CST816S touch interface (#20213)
• NeoPool hydrolysis FL1 and Redox flag (#20258)
• Matter support for password for remote Tasmota devices (#20296)
• Display of active drivers using command status 4
• ESP32 used UART information
• HASPmota haspmota.page_show() to change page (#20333)
• Berry introspect.set() for class attributes (#20339)
• Support negative power on BL0942 using index 5..8 (#20322)

Breaking Changed

• Refactoring of Berry animate module for WS2812 Leds (#20236)

Changed

• Support syslog updates every sleep or every second if #define SYSLOG_UPDATE_SECOND (#20260)
• ESP32 platform update from 2023.11.01 to 2023.12.00 (#20298)
• Moved Berry animate to its own berry_animate lib (#20309)
• Relax checks of Partition Wizard for newest Shelly (#20349)

Fixed

• Matter Contact sensor was not triggering any update (#20232)
• CVE-2021-36603 Cross Site Scripting (XSS) vulnerability (#12221)
• ESP32 piezo ceramic buzzer doesn't buzz (#20118)
• Syslog server warning caused by lack of field and hostname starting with 'z' (#14689)
• Support for Domoticz floor/room topics. Regression from v12.0.1 (#20299)
• Berry claiming UART0 if needed (#20324)
• LVGL fix type for lv_imgbtn (#20354)

[13.3.0] 20231213

• Release Quinlan

[13.2.0.3] 20231213

Added

• DeepSleep support through TIMERS (#20117)
• Command WebCanvas linear-gradient(#F02 7%,#F93,#FF4,#082,#00F,#708 93%) to set GUI canvas

Breaking Changed

• Remove Berry every_200ms event which didn't work anyways (#20205)

Changed

• ESP32 LVGL library from v8.3.10 to v8.3.11 (no functional change)
• Berry ULP API changes for Core3/IDF5 (#20198)
• Berry leds animation refactoring stage 1 (#20197)

Fixed

• TUYA state machine (in TUYA v1) (#20110)
• ESP32 Neopixel flicker for Core3/IDF5 (#20196)
• HASPmota bar fixed val attribute (#20208)

[13.2.0.2] 20231130

Added

• Scripter TCP client (#19914)
• Berry debug.gcdebug() to enable GC debugging (#19936)
• Berry AES_CBC to crypto module (#19964)
• NeoPool sensor delta trigger (command NPTelePeriod) (#19973)
• NeoPool store settings on unified file system (#19973)
• NeoPool command NPBoost (#19973)
• ESP32 Partition Wizard can be loaded dynamically (#19980)
• Berry scale_int, equivalent of scale_uint for signed integers (#20090)
• ESP32 support for Avago Tech Bluetooth Buttons (#20088)

Changed

• Matter update hierarchy of plugins (#19915)
• NeoPool NPHydrolysis percent and unit (#19924)
• Thermostat JSON index from 0 to 1 (#20011)
• ESP32 platform update from 2023.11.00 to 2023.11.01 (#20087)

Fixed

• Scripter timer issue (#19914)
• Zero-Cross Dimmer for ESP32 with Core3 (#19929)
• Matter flow sensor (#19961)
• Berry gpio.dac_voltage() regression from v13.1.0.1 (#19997)
• ESP32-C3 ledlink functionality regression from v13.1.0.2
• Berry parser error in specific cases (#20059)
• changeUIntScale for linearity when expanding range (#20089)
• ESP32 remove restart energy logging if no energy monitoring is selected
• WebQuery response buffer corruption and format character % (#20111)

[13.2.0.1] 20231103

Added

• I2C bus2 support to iAQ core sensor (#19799)
• I2C bus2 support to HTU temperature and humidity sensor
• I2C bus2 support to BH1750 ambient light sensor
• I2C bus2 support to ADS1115 A/D Converter
• I2C bus2 support to SHTxX temperature and humidity sensor
• I2C bus2 support to HYTxxx temperature and humidity sensor
• I2C bus2 support to SI1145/6/7 Ultra violet index and light sensor
• I2C bus2 support to LM75AD temperature sensor
• Command GpioRead to show input state (#19810)
• ESP32 core v3 auto TasConsole USB or Serial connection by @staars
• Support for Winsen XH03x dust particle sensors using USE_PMS5003 and PMS_MODEL_ZH03X (#19850)
• NeoPool hydrolysis setpoint and max
• NeoPool command NPFiltrationSpeed to set non-standard filtration type speed (#19857)
• NeoPool SetOption157 to output sensitive data (#19857)
• NeoPool enhancements for HA (#19857)
• ST7735S display.ini for 1.44 inch 128x128 red SPI display (#19862)
• HASPmota add styling properties (#19912)
• Matter flow sensor support (#19852)

Breaking Changed

• NeoPool SENSOR topic Power renamed to Powerunit (#19857)

Changed

• Prepare I2C drivers for bus2 support
• Matter Light0 now accept a Relay number (#19809)
• ESP32 keep FS intact when over flashing with VSC (#19816)
• Increase MAX_HUE_DEVICES to 32 (#19820)
• MI32 updates (#19893)

Fixed

• NeoPool filtration mode display (#19801)
• Compile USE_PID (#19890)
• ESP32 I2C allow bus2 support when bus1 is not enabled
• ESP32 IR receive with Arduino Core 3 (#19904)

[13.2.0] 20231019

• Release Quincy

[13.1.0.4] 20231019

Added

• Support for HC8 CO2 sensor (#19714)
• ESP32 commands Ds18Rescan and Ds18RetryRead (#19700)

Breaking Changed

• Removed support for Homekit in favour of Matter (#19738)

Changed

• ESP32 Framework (Arduino Core) from v2.0.13 to v2.0.14
• MAX31855/MAX6675 sensors driver support up to 6 (#19329)
• ESP32 analog from analogRead() to calibrated analogReadMilliVolts() (#19732)
• I2S refactoring in preparation for core 3 (#19749)
• Teleinfo use Apparent Power as Active Power approximation (#19756)

Fixed

• ESP32 shutter frequency (#19717)
• ModbusBridge write memory leak (#19758)
• Zigbee timezone when device reads LocalTime attribute (#19772)

Removed

• WiFiClientSecure in favour of WiFiClientSecureLightBearSSL (#19725)

[13.1.0.3] 20231003

Added

• Support for Shelly PlusPMMini, Plus1Mini and Plus1PMMini
• Matter support for Virtual Devices controllable via Rules or Berry (#19520)
• Berry read and write Counters (#19558)
• ESP32 support for influxdb access using https (#19582)
• Support for ENS16x (air quality) and ENS210 (temp & RH) sensors (#19479)
• Support for non-persistent WebButton17 to WebButton32 (#19580)
• Command Mi32Name (#19619)

Changed

• ESP32 Framework (Arduino Core) from v2.0.12 to v2.0.13
• ESP32 LVGL library from v8.3.9 to v8.3.10 (no functional change)
• Consolidate SGP40 and SGP41 into SGP4x driver (#19560)
• ESP32 Audio preparation for Arduino Core v3 (#19637)
• ESP32 LittleFS updated to version with grow option (#19635)
• ESP32 Partition Wizard grow filesystem support (#19645)

Fixed

• ESP32 DS18x20 driver support extended over GPIO33
• ESP32 Shutter button quad press (#19589)
• Compile error with new email lib (#19608)
• ESP32 Arduino Core v2 wifi client flush (#19642)

[13.1.0.2] 20230914

Added

• Support for HDMI CEC protocol (#19434)
• Support different baudrates on BL0942

Breaking Changed

• Sendmail upgraded to ESP-Mail-Client v3.4.9 from v1.2.0, using BearSSL instead of MbedTLS (#19460)

Changed

• Berry fast_loop is now called every 5ms whatever the Sleep value (#19436)
• Reduce IRAM consumption of HDMI CEC to 1453 bytes (#19452)
• ESP32 Framework (Arduino Core) from v2.0.11 to v2.0.12
• ESP32 LVGL library from v8.3.8 to v8.3.9 (no functional change)

Fixed

• PCF8574 mode 1 with base relays exception 3/28 regression from v12.4.0.4 (#19408)
• Berry make mdns compatible with non-IPv6 builds
• ESP32 Shutter migration (#19454)
• ESP32 Shutter multi press button events (#19465)
• Support for IPv6 link-local zones for esp-idf 5.1 (necessary for Matter)
• ESP32-C3 relay click on restart

[13.1.0.1] 20230831

Added

• Commands to allow setting of timeprop parameters (#19310)
• Variables %power<1..28>% and %switch<1..28>% to rules (#19331)
• Experimental support for ESP32-C2 and ESP32-C6 using Arduino core v3.0

Changed

• Display invert setting after tasmota start in uDisplay driver (#19337)

Fixed

• Shutter invert (#19341, #19374)
• Teleinfo power (#19381)
• Exception 3 in IRHVAC (#19389)

[13.1.0] 20230815

• Release Quentin

[13.0.0.4] 20230815

Added

• ESP32 prepare for Arduino Core v3 and esp-idf v5 (#19264)

Changed

• Console height from default 318 pixels to viewport (#19241)
• Shutter button hold behaviour with grouptopic (#19263)
• Thermostat improvements (#19279)
• PID controller improvements (#19285)
• HDC1080 detect device offline (#19298)
• ADE7953 lowered no load threshold (#19302)

[13.0.0.3] 20230805

Added

• Support for MAX17043 fuel-gauge systems Lipo batteries (#18788)
• Support for multiple PCA9685 with extended functionality (#18805)
• Zigbee decode Aqara 0000/FF01 attribute 03 as Temperature (#19210)
• Berry bytes get and set work for 3 bytes values (#19225)
• Matter support for fabric_filtered request (for Google compatibility) (#19249)

Changed

• Initial DisplayMode from 1 to 0 and DisplayDimmmer from 10% to 50% (#19138)
• ESP32 Framework (Arduino Core) from v2.0.10 to v2.0.11
• Berry mqtt.publish now distinguishes between string and bytes (#19196)
• IRremoteESP8266 library from v2.8.5 to v2.8.6
• ESP32 autodetect flashsize and adjust filesystem (#19215)
• Reduced log level for TeleInfo (#19216)
• Matter increased polling frequency for local switches/occupancy (#19242)

Fixed

• Initial battery level percentage (#19160)
• Berry SK6812_GRBW crash (#19166)
• ESP8266 SPI initialization for scripter, filesystem and MFRC522 (#19209)
• Zero cross dimmer minimum interrupt time (#19211)
• Fade would fail when the difference between start and target would be too small (#19248)
• Inverted shutter (#19243)
• Matter support for large attribute responses (#19252)
• Matter auto-configuration Relay indices (#19255)

[13.0.0.2] 20230721

Added

• Partition Wizard is now able to convert to safeboot from Shelly partition layout (#19034)
• Matter mini-profiler (#19075)
• Berry _class can be used in static var initialization code (#19088)
• Berry energy.update_total() to call EnergyUpdateTotal() from energy driver (#19117)
• Support for DeepSleep battery level percentage (#19134)
• Berry metrics for memory allocation/deallocation/reallocation (#19150)
• Berry tasmota.loglevel() and tasmota.rtc_utc() for faster performance (#19152)
• Berry AES CCM decrypting in a single call to avoid any object allocation (#19153)

Changed

• ESP32 shutter driver support up to 16 shutters (#18295)
• Configuration backup and restore now backup and restore .xdrvsetXXX files too (#18295)
• Berry extend range(lower, upper, incr) to arbitrary increment (#19120)
• Berry updated syntax highlighting plugin for VSCode (#19123)
• Matter latency improvement for single attribute reads and single commands (#19158)

[13.0.0.1] 20230708

Added

• Command Delay -1 to wait until next second (#18984)
• Matter add option to disable bridge mode (#18992)
• Support for SGP41 TVOC/NOx Sensor (#18880)
• Command BrRestart to restart the Berry VM (experimental) (#19003)
• Command Restart 9 to save all changes and go into deepsleep waiting for a reset (#19024)
• Berry added getgbl performance counter to debug.counters() (#19070)

Breaking Changed

• Berry bool( [] ) and bool( {} ) now evaluate as false (#18986)
• Berry import strict now detects useless expr without side effects (#18997)

Changed

• Matter support for temperature in Fahrenheit (SetOption8 1) (#18987)
• Matter improve responsiveness (#19002)
• ESP32 LVGL library from v8.3.7 to v8.3.8 (no functional change)
• Matter improve latency for remote commands (#19072)

Fixed

• Berry various fixes for Walrus Operator (#18982)
• MiElHVAC power commands regression from v12.4.0.1 (#18923)
• BrRestart now supports web handlers to work after Berry restart

Removed

• Support for ESP32-C3 with chip revision below 0.3 (old development boards)

[13.0.0] 20230626

• Release Qasim

[12.5.0.4] 20230626

Added

• Matter ability to add or remove endpoint in bridge mode (code only)
• Matter add controller's Vendor Name to logs and UI
• Matter redesigned UI
• Matter add support for Contact Sensor
• Berry string.format() now automatically converts type according to format
• Matter add friendly-name (NodeLabel) to each endpoint
• Berry add global function format as a simpler syntax to string.format
• Berry added f-strings as an alternative to string formatting
• Matter display the remote Device Name instead of IP address
• Berry Walrus operator ':='
• Zigbee firmware for Sonoff-ZB-Pro v20230507

Changed

• Berry webclient.url_encode() is now a static class method, no change required to existing code (#18775)
• Matter Bridge mode always on
• ESP32 Framework (Core) from v2.0.9 to v2.0.10
• Berry code size optimizations

Fixed

• Interaction of SetOption92, VirtualCT, and RGBWWTable (#18768)
• Fixed HASPmota event when value is non-integer (fixes #18229)
• Matter fix local Occupancy sensor
• Zigbee fixed regression with SetOption101
• Berry fixed parser error with upvals in closures
• NeoPool fix NPFiltration switch result (#18871)

[12.5.0.3] 20230602

Added

• Command WifiPower 0 to enable dynamic wifi power based on RSSI by @TD-er (#15443)
• Command WifiPower 1 to restore default wifi power
• HASPmota meta attribute and improved berry_run (#18685)
• Matter bridge for ESP8266 remote endpoints (experimental) (#18734)
• Display descriptor for ST7735 128x160 display (#18741)
• Matter support for Occupancy via Switch (experimental) (#18742)
• Berry RS256 crypto algorithm (RSASSA-MCKS1_v1-5 with SHA256) used for JWT (#18763)
• Berry add set_lsb_justified(bool) to AudioOutputI2S (#18774)

Breaking Changed

• Matter relay number starts at 1 instead of 0 to match Tasmota numbering

Changed

• InfluxDb resolves DNS name before request (#18015)
• Shutter sliders in WEBGUI automatically appear and disappear during configuration and update during movement (#18701)
• AdafruitFingerprint library from v2.0.4 to v2.1.0

Fixed

• ESP32 InfluxDb initial connection delays using HTTPClient (#18015)
• Shutter bootloop using more than 4 shutters (#18673)
• AIThinker webcam issues (#18652)
• Berry tasmota.wifi() would wrongly report wifi as up
• Inverted shutter now reflect status also in WEBGUI and several minor fixes to make "inverted" consistent (#18701)
• Matter fix fabric provisioning from CASE session for iOS 16.5 (#18709)
• ESP32 SPI initialization for MFRC522 (#18711)
• Freeze BMP readings before deepsleep (#18720)
• ESP32 Neopixel busy time adjustment (#18723)
• Zigbee attributes handling in Berry mapping (#18747)

[12.5.0.2] 20230516

Added

• Matter support for Shutters with Tilt
• Matter POC for remote Relay
• Support for Zero-Cross Dimmer on ESP32, changed calculation on ESP8266, high resolution control e.g. Solar: ZCDimmerSet
• ESP32 Enhanced Shutterbuttons functionality to control tilt position, additionally incr/decr possible to position and tilt.
• ESP32 command Shuttersetup for "Shelly 2.5 pro" automatic calibration and setup (experimental)
• Berry tcpclientasync class for non-blocking TCP client
• Support for GM861 1D and 2D bar code reader (#18399)
• Berry re (regex) add match2 and optional offset
• Support for PCA9557 8-bit I/O expander (#18632)
• Matter support for async HTTP for bridged devices (#18656)
• Zigbee support for air sensors (#18665)
• Command I2cScan0 to scan both buses on ESP32 with one command

Breaking Changed

• Change command FileUpload index binary data detection from >199 to >299

Changed

• ESP32 Framework (Core) from v2.0.8 to v2.0.9
• autoconf extract display.ini to file system
• IRremoteESP8266 library from v2.8.4 to v2.8.5
• Energy power delta report delayed by two seconds allowing hardware to stabilize (#17751)

Fixed

• Partition_Manager.tapp fixed
• Berry fixed a rare condition when a GC causes a memory corruption
• LED PWM ac_dimmer curve was wrongly applied instead of Gamma regression from v12.2.0.5 (#18666)

[12.5.0.1] 20230505

Added

• Matter sensors Humidity, Pressure, Illuminance; optimize memory (#18441)
• Command SetOption152 0/1 to select two (0 = default) pin bistable or one (1) pin latching relay control (#18386)
• Matter allow Matter#Initialized rule once the device is configured (#18451)
• Matter UI to change endpoints configuration (#18498)
• Matter support for Shutters (without Tilt) (#18509)
• Support for TC74 temperature sensor by Michael Loftis (#18042)

Changed

• ESP32 Framework (Core) from v2.0.7 to v2.0.8
• Refactored Zero Cross Dimmer (#18481)
• ESP32 LVGL library from v8.3.6 to v8.3.7 (no functional change)

Fixed

• ESP8266 Energy Export Active no update regression from v12.3.1.3
• NovaSDS GUI values (#18444)
• Berry fix rules for string comparisons (#18464)
• Shutter: GarageMode does not stop on console commands, ShutterSetOpen and ShutterSetClose does not reset direction (#18539)

[12.5.0] 20230417

• Release Peyton

[12.4.0.5] 20230417

Added

• Matter support for Light and Relays on ESP32 by Stephan Hadinger (#18320)
• ESP32 WIP support for 16 shutters using #define USE_SHUTTER_ESP32 in addition to USE_SHUTTER by Stefan Bode (#18295)
• Berry webserver.html_escape() reusing the internal HTML escaping function
• Support for GDK101 gamma radiation sensor by Petr Novacek (#18390)
• Matter support in now stabilized for Apple and Google (not tested with Alexa)
• Berry instrospect.name() to get names of functions, modules and classes (#18422)
• Berry add searchall() and matchall() to re module and pre-compiled patterns (#18429)
• Matter automatically exposes all detected Temperature sensors (#18430)

Changed

• ESP32 LVGL library from v8.3.5 to v8.3.6 (no functional change)

Fixed

• ESP32 Upload, Upgrade, WebGetConfig, WebQuery and WebSend random HTTP(S) connection timeout set to 5 sec (commit 542eca3)
• ESP32 energy monitoring set StartTotalTime regression from v12.3.1.5 (#18385)

[12.4.0.4] 20230403

Added

• Matter support simple Relay on Apple Homekit by Stephan Hadinger (#18239)
• VSC Pio menu bar extensions by @Jason2866 (#18233)
• Command SwitchMode0 to show or set all SwitchModes

Changed

• Support for multiple PCF8574 as switch/button/relay if enabled with #define USE_PCF8574 and #define USE_PCF8574_MODE2

[12.4.0.3] 20230322

Added

• Support for PMSA003I Air Quality Sensor by Jean-Pierre Deschamps (#18214)
• Support for DingTian virtual switch/button/relay (#18223)
• Berry add mdns.remove_service()

Fixed

• Refactor energy monitoring reducing stack usage and solve inherent exceptions and watchdogs (#18164)
• Berry fix tasmota.get_power(index)

[12.4.0.2] 20230317

Added

• Support for multiple MCP23008 as switch/button/relay if enabled with #define USE_MCP23XXX_DRV
• Support for multiple PCF8574 as switch/button/relay
• Extended Tariff command for forced tariff (#18080)
• Berry support for Tensorflow Lite (TFL) by Christiaan Baars (#18119)
• Zigbee send Tuya 'magic spell' to unlock devices when pairing (#18144)
• Berry webclient set_follow_redirects(bool)
• Berry webclient collect_headers() and set_headers
• Display TM1650 commands like TM1637 (#18109)
• Berry add web_get_arg event to drivers when FUNC_WEB_GET_ARG event is processed
• Support for reset settings on filesystem

Breaking Changed

• Shelly Pro 4PM using standard MCP23xxx driver and needs one time Auto-Configuration

Changed

• Refactored Berry rule engine and support for arrays
• ESP32 LVGL library from v8.3.3 to v8.3.5 (no functional change)
• Removed absolute url from filesystem (#18148)
• UrlFetch now follows redirects

Fixed

• TuyaMcu v1 sequence fix (#17625)
• TuyaMcu v1 timer integer overflow (#18048)
• PZEM energy monitor stabilize period on larger configs (#18103)
• Rule topic comparison (#18144)
• ESP32 energy period shows kWh value instead of Wh regression from v12.3.1.5 (#15856)

[12.4.0.1] 20230301

Added

• Matter read/write and commands (#18000)
• Matter subscriptions (#18017, #18018)
• Matter multi-fabric (#18019)
• Support for multiple MCP23017/MCP23S17 as switch/button/relay
• NTP time request from gateway (#17984)

Changed

• ADC Range oversample from 2 to 32 (#17975)
• ESP32 Framework (Core) from v2.0.6 to v2.0.7
• Move #define OTA_URL from user_config.h to board files for better initial support (#18008)
• Increase number of (virtual)relays and (virtual)buttons to 32
• LibTeleinfo from v1.1.3 to v1.1.5 (#18050)

Fixed

• SEN5X floats and units (#17961)
• Energytotals cannot be set to negative values (#17965)
• Undocumented support for non-sequential buttons and switches (#17967)
• SR04 driver single pin ultrasonic sensor detection (#17966)
• IR panasonic protocol regression from v12.0.2.4 (#18013)
• EnergyTotal divided twice during minimal upgrade step regression from v12.3.1.3 (#18024)

[12.4.0] 20230216

• Release Peter

[12.3.1.6] 20230216

Added

• ESP32 preliminary support for Matter protocol, milestone 1 (commissioning) by Stephan Hadinger
• Basic support for Shelly Pro 4PM
• Command DhtDelay<sensor> <high_delay>,<low_delay> to allow user control over high and low delay in microseconds (#17944)
• Berry int64.fromstring() to convert a string to an int64 (#17953)

Breaking Changed

• TM1638 button and led support are handled as virtual switches and relays (#11031)

Changed

• Dht driver from v6 to v7
• LVGL allow access to lv.LAYOUT_GRID and lv.LAYOUT_FLEX (#17948)
• TuyaMcu support of virtual switches

Fixed

• ESP8266 Fix TLS SNI which would prevent AWS IoT connection (#17936)
• TuyaMcu exception 3 regression from v12.3.1.4

[12.3.1.5] 20230208

Added

• ESP32 support for eigth energy phases/channels
• ESP32 command EnergyCols 1..8 to change number of GUI columns
• ESP32 command EnergyDisplay 1..3 to change GUI column presentation
• Support for SEN5X gas and air quality sensor by Tyeth Gundry (#17736)
• Berry add mdns advanced features and query
• ESP32 support for Biomine BioPDU 625x12 (#17857)

Breaking Changed

• Berry energy_ctypes changed with new energy driver
• Berry energy_ctypes fixed accordingly

Changed

• Energy refactoring preparing for ESP32 phase/channel extension

Fixed

• ADE7953 when calibration data for second channel is used regression from v12.2.0.2
• Shelly Pro 1/2 relay click at restart regression from v12.3.1.4
• Zigbee extend plug-in modifiers to 16 bits
• Broken I2C priority regression from v12.3.1.3 (#17810)
• Energy usage and return migrated too small (/10000) regression from v12.3.1.3

[12.3.1.4] 20230127

Added

• Berry crypto.EC_P256 ECDSA signature (required by Matter protocol)
• Berry add up flag to tasmota.wifi() and tasmota.eth(), always return MAC

[12.3.1.3] 20230115

Added

• Support for PCA9632 4-channel 8-bit PWM driver as light driver by Pascal Heinrich (#17557)
• Berry bytes() now evaluates to false if empty
• Berry crypto.AES_CCM (required by Matter protocol)
• ESP32 support for BMPxxx sensors on two I2C buses (#17643)
• Berry add implicit _class parameter to static methods

Changed

• Energy totals max supported value from +/-21474.83647 to +/-2147483.647 kWh
• Removed delays in TasmotaSerial and TasmotaModbus Tx enable switching
• Increase rule event buffer from 100 to 256 characters (#16943)
• All calls to atof() into CharToFloat() reducing code size by 8k
• Keep webserver enabled on command upload

Fixed

• Energy dummy switched voltage and power regression from v12.2.0.2
• Orno WE517 modbus serial config 8E1 setting (#17545)
• No IP address shown when in AP mode regression from v12.3.1.1 (#17599)
• Rename tasmota4M.bin to tasmota-4M.bin to solve use of tasmota-minimal.bin (#17674)
• DNS lookup for upload from ota server using http regression from v12.3.1.1

[12.3.1.2] 20221231

Added

• Berry crypto add EC_P256 and PBKDF2_HMAC_SHA256 algorithms required by Matter protocol
• Berry crypto add random to generate series of random bytes
• Berry crypto add HKDF_HMAC_SHA256
• Support for up to 3 single phase modbus energy monitoring device using generic Energy Modbus driver
• Berry crypto add SPAKE2P_Matter for Matter support
• Support for IPv6 only networks on Ethernet (not yet Wifi)
• Support for TM1650 display as used in some clocks by Stefan Oskamp (#17594)

Changed

• ESP32 Framework (Core) from v2.0.5.4 to v2.0.6 (IPv6 support)
• Tasmota OTA scripts now support both unzipped and gzipped file uploads (#17378)
• NTP default servers to dual-stack (IPv4/IPv6)
• Revert TuyaMcu rewrite by btsimonh as lack of support

Fixed

• Shutter default motorstop set to 0 (#17403)
• Shutter default tilt configuration (#17484)
• Modbus transmit enable GPIO enabled once during write buffer
• ESP8266 set GPIO's to input on power on fixing relay spikes (#17531)

[12.3.1.1] 20221221

Added

• Support for IPv6 DNS records (AAAA) and IPv6 Ping for ESP32 and ESP8266 (#17417)
• Berry support for crypto.SHA256 (#17430)
• Support for RGB displays (#17414)
• Berry add crypto AES_CTR, HDMAC_SHA256, MD5

Changed

• ESP32 Framework (Core) from v2.0.5.3 to v2.0.5.4 (IPv6 support)

[12.3.1] 20221216

• Release Percy

[12.3.0.1] 20221216

Changed

• ESP32 initial otaurl from http to https

Fixed

• ESP8266 zigbee exception 3 regression from v12.3.0 (#17397)

[12.3.0] 20221215

• Release Percy

[12.2.0.6] 20221215

Added

• Serial Modbus transmit enable GPIOs to all modbus energy drivers and modbus bridge (#17247)
• Berry crypto module, with AES_GCM by default and EC_CC25519 optional
• IPv6 support for Ethernet (ESP32)
• Support for ME007-ULS narrow FoV ultrasonic distance sensor by Mathias Buder (#17376)

Changed

• TasmotaSerial library from v3.5.0 to v3.6.0
• Removed leading spaces on commands (S)SerialSend1 to 6 but keep on duplicate commands (S)SerialSend11 to 16 (#16723)
• MQTT now uses Tasmota's DNS resolver instead of LWIP (#17387)
• Shutter bug fixes and functionality upgrade (#17380)

Fixed

• TasmotaSerial read(buffer, size) regression from v9.3.0
• RCSwitch exception 0/6 on some protocols (#17285)
• ESP32 exception 28 when RtcNtpServer is enabled on restart (#17338)
• Analog MQ exception 28 on restart (#17271)
• ESP32 fix Ping (#17373)

[12.2.0.5] 20221129

Added

• ESP32 DS18x20 parasitic power usage when defining W1_PARASITE_POWER (#17112)
• Optional define SERIAL_BRIDGE_BUFFER_SIZE to set Serial Bridge internal buffer size (Default ESP8266 = 256, ESP32 = 800)
• Command SSerialBuffer 256..SERIAL_BRIDGE_BUFFER_SIZE to change serial bridge rx buffer size (#17120)
• Command SetOption35 0..255 to skip number of received messages in Serial Bridge (default 0) (#17140)
• Teleinfo TEMPO (BBR) contract (#17160)
• Support for HLK-LD2410 24GHz smart wave motion sensor
• Berry mdns module (#17202)
• IPv6 preview for ESP32, also working for ESP8266

Changed

• Serial Bridge default internal serial rx buffer size from 64 to 256 (#17120)
• Accept filename extensions to GUI file upload input fields (#16875)
• AC PWM dimmer lineair power distribution (#17177)

Fixed

• ModbusBridge baudrates over 76500 baud (#17106)

Removed

• Accept filename extensions to GUI file upload input fields as not functional in some browsers (#16875)

[12.2.0.4] 20221117

Added

• Support for Plantower PMSx003T AQI models with temperature and humidity (#16971)
• Support for Dingtian x595/x165 shift register based relay boards by Barbudor (#17032)
• New FUNC_NETWORK_UP and FUNC_NETWORK_DOWN events
• WS2812 and Light ArtNet DMX control over UDP port 6454 (#17059)
• Command SwitchMode 16 sending only MQTT message on inverted switch change (#17028)
• Support for HMC5883L 3-Axis Digital Compass sensor by Andreas Achtzehn (#17069)
• Berry add udp->close() method (#17094)
• Command RgxClients for range extender clients list (#17048)
• Command RgxPort [tcp|udp], gateway_port, client_mac, client_port for range extender port forwardings (#17092)

Changed

• Reverted Flash Mode back from DIO to DOUT for ESP8266/ESP8285 (#17019)
• ESP32 Framework (Core) from v2.0.5.2 to v2.0.5.3 (#17034)
• TuyaMcu rewrite by btsimonh (#17051)
• WS2812 sends signal to only Pixels leds instead of sending to 512 leds (#17055)
• Zigbee improved Aqara plug support and completed cluster 0x0702 (#17073)
• ESP32 LVGL library from v8.3.2 to v8.3.3 (no functional change)

Fixed

• SenseAir S8 module detection (#17033)

[12.2.0.3] 20221109

Added

• Support for BP1658CJ RGBCW led bulbs like Orein OS0100411267 by Cossid (#17011)

Breaking Changed

• Redesign distance sensors VL53LXX, TOF10120, HRXL and DYP to use cm instead of mm (#17021)

Changed

• Default Flash Mode changed from DOUT to DIO for ESP8266/ESP8285

[12.2.0.2] 20221107

Added

• Support for Digital Addressable Lighting Interface (DALI) by Andrei Kazmirtsuk (#16938)
• Support for two phase power calibration using commands PowerSet2, VoltageSet2 and CurrentSet2
• Support for NTAG2xx tags read and write on PN532 NFC reader (#16939)
• Berry bytes().reverse() method (#16977)
• ESP32 Support for DMX ArtNet Led matrix animations (#16984)
• Command SetOption47 1..255 to delay power on relay state in seconds reducing power surge. SO47 1 delays until network connected. SO47 2 delays until mqtt connected
• ESP32 DMX ArtNet optimization to avoid any object allocation and avoid garbage collector pauses
• Berry add dyn class

Changed

• Move some persistent data (PowerLow)
• ESP32 Framework (Core) from v2.0.5 to v2.0.5.2
• ADE7953 monitoring from instant power to accumulated energy (#16941)

Fixed

• Deduplicate code and fix %timer n% rule regression from v12.2.0 (#16914)
• Serial initialization for baudrate and config (#16970)
• ModbusBridge buffer overflow (#16979)
• Default serial bridge configuration from 5N1 to 8N1 regression from v10.1.0.3

Removed

• Define USE_PN532_DATA_RAW from NFC reader (#16939)

[12.2.0.1] 20221026

Added

• DS18x20 support on up to four GPIOs by md5sum-as (#16833)
• Berry add bytes().setbytes() (#16892)
• Support for Shelly Pro 1/1PM and 2/2PM (#16773)
• Add Zigbee router firmware for Sonoff ZBBridgePro (#16900)
• Prepare for DMX ArtNet support on ESP32

Changed

• DS18x20 DS18Alias to DS18Sens (#16833)
• Compiling with reduced boards manifests in favour of Autoconfig (#16848)
• Add NeoPool NPFiltration 2 toggle cmnd (#16859)
• ESP32 NimBLE library from v1.4.0 to v1.4.1 (#16775)

Fixed

• BP5758D red channel corruption regression from v12.1.1.6 (#16850)

[12.2.0] 20221017

• Release Patrick

[12.1.1.6] 20221017

Added

• Command WcClock 10..200 set webcam clock in MHz. Default is 20
• ESP32 Automatically resize FS to max flash size at initial boot (#16838)
• Command SspmPowerOnState<relay> 0|1|2 to set Sonoff SPM 4Relay module v1.2.0 power on state overruling tasmota global power on state. 0 = Off, 1 = On, 2 = Saved state (#13447)
• Support for Flash size 32/64/128 MB in Partition Wizard and auto-resize

[12.1.1.5] 20221013

Added

• Command Sunrise 0..3 to select sunrise dawn angle between Normal, Civil, Nautical or Astronomical (#16795)

[12.1.1.4] 20221012

Added

• Support for Shelly Plus 2PM using template {"NAME":"Shelly Plus 2PM PCB v0.1.9","GPIO":[320,0,0,0,32,192,0,0,225,224,0,0,0,0,193,0,0,0,0,0,0,608,640,3458,0,0,0,0,0,9472,0,4736,0,0,0,0],"FLAG":0,"BASE":1,"CMND":"AdcParam1 2,10000,10000,3350"}
• Zigbee Alexa/Hue emulation, support multiple switches on separate endpoints (#16718)
• Support for QMC5883L magnetic induction sensor by Helge Scheunemann (#16714)
• LVGL/HASPmota add tiny "pixel perfect" fonts for small screens (#16758)
• HASPmota support for TTF fonts (#16759)
• Support for Modbus Energy Monitoring devices using a rule file. See xnrg_29_modbus.ino for more information

Changed

• ESP32 LVGL library from v8.3.0 to v8.3.2
• Increase serial console fixed input buffer size from 520 to 800
• Swap Shelly EM internal channels A and B to match P1 and P2 (#16486)

[12.1.1.3] 20221003

Added

• ESP32-S2 and ESP32-S3 touch button support
• Zigbee friendly names per endpoint

Fixed

• ESP32 touch button multi-press and hold detection (#16596)

[12.1.1.2] 20220927

Added

• Berry has persistent MQTT subscriptions: auto-subscribe at (re)connection
• Berry automated solidification of code
• Support of optional file calib.dat on ADE7953 based energy monitors like Shelly EM (#16486)
• Command SetOption46 0..255 to add 0..255 * 10 milliseconds power on delay before initializing I/O (#15438)
• Zigbee support for decimal Voltage/Current/Power on power metering plugs
• Command UrlFetch <url> to download a file to filesystem
• Zigbee basic support for Green Power
• Berry add introspect.setmodule(name:string, value:any) -> nil

Changed

• ESP32 Increase number of button GPIOs from 8 to 28 (#16518)
• IRremoteESP8266 library from v2.8.2 to v2.8.3
• Tasmota Core32 from 2.0.4.1 to 2.0.5
• IRremoteESP8266 library from v2.8.3 to v2.8.4
• Zigbee report unprocessed attributes
• Platformio one Platform for all Tasmota frameworks Core32 2.0.5 (#16644)

[12.1.1.1] 20220910

Added

• Support for SGP40 gas and air quality sensor (#16341)
• Support for Modbus writing using ModbusBridge by JeroenSt (#16351)
• Support for Ethernet in ESP32 safeboot firmware (#16388)
• Flowrate meter flow amount/duration, show values in table format (#16385)
• Zigbee prepare for Green Power support (#16407)
• Command SetOption146 1 to enable display of ESP32 internal temperature
• Support for DFRobot SEN0390 V30B ambient light sensor (#16105)
• Command DspSpeed 2..127 to control message rotation speed on display of POWR3xxD and THR3xxD
• Command DspLine<1|2> <index>,<unit>,<index>,<unit>,... to select message(s) on display of POWR3xxD and THR3xxD

Changed

• TasmotaModbus library from v3.5.0 to v3.6.0 (#16351)
• Button debouncing V3 by adopting switch debounce code (#16339)
• Thermostat max allowed temperature from 100 to 200C (#16363)
• Using command SerialBuffer raise max allowed buffer size to 2048 characters (#16374)

Fixed

• Removed whitespace from JSON values with no decimals (#16365)

[12.1.1] 20220825

• Release Patricia

Fixed

• RTC not detected when lights are present (#16242)
• DNS lookup for .local domains (#16273)
• Button response delay regression from v12.0.2.4 (#16319)
• Lost module name in GUI regression from v12.0.2.4 - 20220803 (#16324)
• LVGL fix descriptors Berry mapping

[12.1.0.1] 20220825

Added

• Zigbee device plugin mechanism with commands ZbLoad, ZbUnload and ZbLoadDump (#16252)
• ESP32-S3 support for internal temperature sensor
• Command StatusRetain (#11109)

Changed

• ESP32 NimBLE library from v1.3.6 to v1.4.0

[12.1.0] 20220818

• Release Patricia

[12.0.2.4] 20220818

Added

• Command SetOption45 1..250 to change default bistable latching relay pulse length of 40 milliseconds
• Support for Modbus bridge adding commands ModbusSend, ModbusBaudrate and ModbusSerialConfig (#16013)
• Support for multiple IRsend GPIOs (#16138)
• Zigbee added recording of when the battery was last reported (#16146)
• Zigbee add Battery auto-probe (can be disabled with SetOption143 1) (#16148)
• Zigbee include "BatteryPercentage" in all messages
• Commands WifiScan and WifiTest (#16141)
• Support for Catalan language translations by Albert Gonzalez (#16145)
• Zigbee SetOption144 1 includes a timestamp in ZbReceived messages

Changed

• ESP32 LVGL library from v8.2.0 to v8.3.0 (#16019)
• Tasmota ESP32 Arduino core from v2.0.4 to v2.0.4.1 (#16110)
• TasmotaModbus library from v3.4.0 to v3.5.0 (#16245)

Fixed

• Restore EnergyToday after using command restart 2 and power cycle (#16118)
• Fixed IR crash on ESP32 (#16173)
• Zigbee fix Tuya for writing attributes

[12.0.2.3] 20220716

Added

• Support for Sonoff POWR3xxD and THR3xxD (#15856)
• Support for bistable (latching) relays mixed with monostable relays using GPIO Relay_b or Relay_bi as used by Sonoff POWR320D and THR320D
• ESP32 Support for Ultra Low Power (ULP) coprocessor via Berry by Christian Staars (#15916)
• Command Sleep2 ! to cancel pending one-shot speed setting (#15954)

Changed

• Driver DHT v6 consolidation for both ESP8266 and ESP32 to support SI7021, THS01 and MS01 on ESP32 (#15856)
• Tasmota ESP32 Arduino core from v2.0.3 to v2.0.4 (#15940)

[12.0.2.2] 20220701

Added

• Command GlobalTemp2 1..250 to select Global Temperature source indexed from teleperiod occurrence data (#15834)
• Command GlobalHum2 1..250 to select Global Humidity source indexed from teleperiod occurrence data (#15834)
• Command GlobalPress2 1..250 to select Global Pressure source indexed from teleperiod occurrence data (#15834)

[12.0.2.1] 20220622

Added

• Support for 5-channel light dimmer driver SM2335 used in SwitchBot Color Bulbs (#15839)

Fixed

• ESP32 SendMail not working over ethernet (#15794)

[12.0.2] 20220620

• Release Paul

[12.0.1.2] 20220620

Added

• Command DnsTimeout 100..20000 to change default DNS timeout from 1000 msec blocking if no DNS server found

Fixed

• MQTT rc -4 on connections regression from v12.0.0 (#15809)

[12.0.1] 20220617

• Release Paul

Fixed

• Resolving NTP and/or MQTT server names regression from v12.0.0 (#15816)

[12.0.0] 20220615

• Release Paul

[11.1.0.4] 20220615

Added

• Support for HYTxxx temperature and humidity sensor (#15715)
• Support for Sensirion SHT4X using define USE_SHT3X (#15349)
• Command SSerialSend9 1 to enable Serial Bridge console Tee for debugging purposes
• Command SetOption142 1 to wait 1 second for wifi connection solving some FRITZ!Box modem issues (#14985)

Changed

• Restructured tasmota source directories taking benefit from PlatformIO Core v6.0.2
• ESP32 increase Serial Bridge input buffer from 130 to 520 characters

Fixed

• ESP32 Arduino Core WiFi timeout is changed from msec to seconds
• Reduce blocking by adding WifiPollDns before resolving NTP and/or MQTT server names (#14394)
• SHT1X driver hangs and wrong values on ESP32 (#15790)

[11.1.0.3] 20220602

Added

• Support for Sonoff SPM v1.2.0
• Support for Sonoff Zigbee Bridge Pro by Stephan Hadinger (#15701)
• Command SspmDisplay 2 to display Sonoff SPM energy data in GUI for user tab-selected relay modules (#13447)
• Command SetOption141 1 to disable display of module name in GUI header
• Support for 5-channel light dimmer driver BP5758D used in Tuya bulbs (#15713)

Fixed

• Possible pin output toggle after power on (#15630)

[11.1.0.2] 20220514

Added

• ESP32 Command Restart 3 to switch between SafeBoot and Production

Changed

• Prepare to remove dedicated Home Assistant discovery in favour of Tasmota Discovery and hatasmota
• ESP32 Tasmota SafeBoot with changed partition scheme allowing larger binaries

[11.1.0.1] 20220504

Added

• Support for Sonoff MS01 soil moisture sensor (#15335)
• Support for daisy chaining MAX7219 displays (#15345)
• Support for light schemes via DDP as default for ESP32x (#15436)
• Command EnergyExportActive<phase> to (p)reset energy export active for supported devices. Currently ADE7880 only (#13515)
• Sonoff SPM delayed SetPowerOnState (#13447)
• Command SetOption139 0/1 to switch between pressure unit "mmHg" (0) or "inHg" (1) when SO24 1 (#15350)
• Support for flowrate meters like YF-DN50 and similar (#15474)
• Command IfxRp ""|<policy> adds optional InfluxDb Retention Policy (#15513)
• Command SetOption140 0/1 to switch between MQTT Clean Session (0) or Persistent Session (1) (#15530)

Fixed

• SCD40 start low power command (#15361)
• Improv initial or erase device installation failing to provide Configure WiFi option
• BL09xx negative power presentation (#15374)

Removed

• Arduino IDE support

[11.1.0] 20220413

• Release Ostara

[11.0.0.7] 20220413

Added

• HX711 command Sensor34 10 0|1|<weight in gram> to set HX711 fixed tare (0 = use auto tare, 1 = use calibrated tare, Any other value is user selected tare)
• Command SetOption138 1 to switch GUI energy multi-column layout from left/center (0) to right (1) align (#15342)

Changed

• HX711 commands Sensor34 11 <valueA> and Sensor34 12 <valueB> to use HX711 absolute weight conversion (#15292)

Fixed

• TasMesh relaunch wifi on esp_now_init failure (#15334)

Removed

• HX711 command Sensor34 7 as now active tare is persistent resulting in calculated current weight

[11.0.0.6] 20220409

Added

• HX711 commands Sensor34 10 <valueA> and Sensor34 11 <valueB> to use HX711 absolute weight conversion (#15292)

Changed

• NeoPool boost command with redox control state, relay and aux detail display

Fixed

• NeoPool filtration state and speed display

[11.0.0.5] 20220407

Added

• Support for improv as used by esp-web-tools
• Command IfxSensor 1 to send non-teleperiod data to influxdb
• ESP32 Support for OpenHASP v1.0 by Stephan Hadinger (#15307)
• Command SetOption137 1 to avoid MQTT publish of defined Tuya CMDs if SO66 is active (#15267)

Changed

• Remove support for Internet Explorer by allowing ECMAScript6 syntax using less JavaScript code bytes (#15280)

Fixed

• ESP32 save settings after OTA upload regression from v10.0.0.3
• HX711 false readings by removing large deviations

[11.0.0.4] 20220402

Added

• Command RtcNtpserver 0/1 to enable Tasmota NTP server when enabled by define RTC_NTP_SERVER
• NeoPool JSON modules, power module, cell info, chlorine, conductivity and ionization
• Support for up to four DS3502 digital potentiometers with command Wiper<x> 0..127
• Command SetOption136 1 to disable single sensor reports from Tuya devices while keeping teleperiod reports (#15216)

Changed

• Consolidate three RTC chip drivers (DS3231, BM8563, PCF85363) into one driver updating RTC as soon as possible after restart
• Removed command Sensor33 and replaced by RtcNtpserver
• DS3231 I2C address define USE_RTC_ADDR into DS3231_ADDRESS
• NeoPool remove ambiguous device color names
• Display of energy values in GUI use columns when define USE_ENERGY_COLUMN_GUI is enabled (default)
• IRremoteESP8266 library from v2.8.1 to v2.8.2
• Tasmota ESP32 Arduino core to v2.0.3
• ESP8266 Shrinked tasmota-minimal.bin by removing all commands except Upgrade, Upload, OtaUrl, Seriallog, Weblog and Restart

Fixed

• NeoPool NPBit and NPRead/NPReadL output
• ESP32 PowerOnState (#15084)

[11.0.0.3] 20220312

Added

• TasmotaSerial implement end()
• ESP32 TasmotaSerial uart mapping to support multiple begin() and implement getUart() (#14981)
• Commands Sensor12 D0 .. D5, S0 .. S5 allowing differential or single-ended modes (#15001)
• NeoPool commands NPpHMin, NPpHMax, NPpH, NPRedox, NPHydrolysis, NPIonization, NPChlorine and NPControl (#15015)
• NeoPool system voltages display
• Full DS3231 integration and synchronisation when using UBX (=GPS), NTP or manual time
• LVGL Splash screen and SetOption135 1 to disable splash screen
• Command RfTimeout 100..60000 to disable duplicate RfReceive. Default 1000 (#15061)
• Support for ADE7880 3 phase energy monitor as used in Shelly 3EM (#13515)
• Support for PCF85363 RTC as used in Shelly 3EM (#13515)

Changed

• Extent number of pulsetimers from 8 to 32 (#8266)
• Tasmota ESP32 Arduino core to v2.0.2.3 (#14979)
• TasmotaSerial library from v3.4.0 to v3.5.0 (#14981)
• NeoPool limit relay output to the number actually available

[11.0.0.2] 20220225

Changed

• Enabled ethernet and Sonoff SPM in tasmota32.bin

[11.0.0.1] 20220220

Added

• Command SspmMap 0 to reset Sonoff SPM default mapping
• Command TcpConnect <port><ip_address> to add client connection mode (#14874)
• ESP32 support for BLE Mi scale V1 (#13517)
• ESP32 integrate Homekit in Bluetooth binary (#14818)
• ESP32 Berry always enable rules
• ESP32 Berry bootloop protection
• ESP32 Berry virtual Alexa hue device (#14833)

Changed

• Adafruit BusIO library from v1.0.10 to v1.11.0
• ESP32 update the internal Berry type system to sync with Skiars Berry repository. No expected impact on code, but .bec files need to be generated again. (#14811)
• ESP32 LVGL library from v8.1.0 to v8.2.0
• ESP32 NimBLE library from v1.3.3 to v1.3.6
• Sonoff SPM increase max number of relays supported to 32 (8 SPM-4Relay modules)

Fixed

• SSPM energy yesterday when zero
• GPIO OptionE1 selection regression (#14821)
• BL0939, BL0940 and BL0942 energy monitoring buffer miscompares resulting in wrong daily energy values regression from v9.5.0.8 (#14829)
• Orno WE517 power meter phase 2 current reactive (#14841)
• Wiegand 34-bit rfid reading and presentation (#14834)

[11.0.0] 20220212

• Release Olivia

[10.1.0.8] 20220212

Changed

• From Calendar Versioning (CalVer) back to Semantic Versioning (SemVer) for better major change indication and future support

[2022.1.4 = 10.1.0.7] 20220205

Added

• Rule variables %timer1% to %timer16% (#14619)

Changed

• Version display from 2022.01.3 to 2022.1.4

Fixed

• SR04 sensor driver regression from 2022.01.2

[2022.01.3 = 10.1.0.6] 20220204

Added

• Command WebTime <start_pos>,<end_pos> to show part of date and/or time in web gui based on "2017-03-07T11:08:02-07:00"
• ESP32 disable serial console when 3 (ESP32) or 2 (Other models) serial interfaces are requested (#14487)
• Support for BME688 with latest Bosch-Sensor-API library (#14513)
• Command SetOption44 1..100 to set base tolerance percentage for matching incoming IR messages (default 25, max 100) (#14555)
• Command Json {<Tasmota commands>} to enable input of any command as JSON tokens (#14568)
• Rule variable %color% (#14572)
• Command SspmDisplay 1 to display Sonoff SPM energy data in GUI for relays powered on only
• Command SspmEnergyTotal<relay> to (p)reset Sonoff SPM total energy without today's energy
• Command SspmEnergyYesterday<relay> to (p)reset Sonoff SPM energy yesterday
• Command SspmHistory<relay> to retrieve Sonoff SPM daily energy up to last six month (as defined by ARM firmware)
• Command SspmIAmHere<relay> to (faintly) blink Sonoff SPM-4Relay module error light of requested relay
• Command SspmLog<relay> [x] to retrieve Sonoff SPM relay power state change and cause logging
• Command SspmOverload<relay> <options> to set Sonoff SPM overload criteria for any relay
• Command SspmScan to rescan Sonoff SPM modbus
• Support for MQ analog sensor for air quality by Francesco Adriani (#14581)
• Command SetOption134 1 to disable PWM auto-phasing for lights by default (new behavior) (#14590)
• Increase PWM channels to 16 (Esp32 only)
• Initial support for ESP32-S3 with support for 38 configurable GPIOs

Changed

• BME68x-Sensor-API library from v3.5.9 to v4.4.7
• ESP32 core library from v2.0.2 to v2.0.2.1 (#14553)

Fixed

• OneWire-Stickbreaker (DS18x20) library support for ESP32-S2 (#14338)

[2022.01.2 = 10.1.0.5] 20220116

Added

• Tasmota favicon to webbrowser tab (#14322)
• Commands for ESP32 ethernet configuration EthIpAddress, EthGateway, EthSubnetmask, EthDnsServer1 and EthDnsServer2 (#14385)
• Support for Eastron SDM230 modBus energy meter (#13443)

Changed

• IRremoteESP8266 library from v2.8.0 to v2.8.1

[2022.01.1 = 10.1.0.4] 20220107

Added

• Experimental ADE7953 (Shelly EM) reset on restart (#14261)
• Command SspmMap 2,1,.. to map Sonoff SPM scanned module to physical module (#14281)
• Solax X1 modbus RTS support and offline status (#14305)
• DDP schemes for light and WS2812 (#14017)
• ESP32 single binary firmware (#14239)
• ESP32 support for USE_PWM_DIMMER as GPIO Option E1
• Support for Linkind dimmer as GPIO Option A6 (#14004)

Changed

• PubSubClient library from v2.8.12 to v2.8.13
• TasmotaSerial library from v3.3.0 to v3.4.0
• TasmotaModbus library from v1.2.0 to v3.4.0
• From Semantic Versioning (SemVer) to Calendar Versioning (CalVer)
• ESP32 Set stack size with #define SET_ESP32_STACK_SIZE, added StackLowMark metrics
• ESP32 Berry stores compiled bytecode into IRAM, freeing space in heap (#14307)

Fixed

• Intermittent exceptions and heap corruption due to PubSubClient library buffer overflow (#13700)
• Scripter memory corruption (#14268)
• Edit file for SD card (#14229)
• Solax X1 negative temperature support (#14278)
• Modbus serial config regression from v10.1.0.3

[10.1.0.3] 20211231

Added

• Command SSerialConfig <serialconfig> to change Serial Bridge configuration

Fixed

• DHT support negative temperatures on different hardware (#14173)
• ESP32 Provide proper OTA_URL for tasmota32solo1 (#14202)
• Hardware serial parity and stop bits support (#14212)

Changed

• LVGL update from 8.0.2 to 8.1.0

[10.1.0.2] 20211225

Changed

• TasmotaSerial library from v3.3.0 to v3.4.0 - reverted (#14153)
• Force initial serial configuration even if no serial GPIO's are enabled (#14153)
• Revert change to fix extra flashwrite before QuickPowerDetection (#14153)
• Increase SerialBridge receive buffer from 130 to 256 characters - reverted (#14153)
• ESP8266Audio library from v1.9.2 to v1.9.5 (#14172)
• ESP8266SAM library from v1.0 to v1.0.1 (#14172)

Fixed

• Serial broken after #14153 - reverted

[10.1.0.1] 20211223

Added

• PWM Dimmer two button support (#13993)
• Device Group Send full status item (#14045)
• Support for MAX7219 Dot Matrix displays (#14091)
• ESP32 support for TuyaMcu
• ESP32 Berry features

Changed

• Mitsubishi HVAC temperature resolution (#13936)
• Remove restriction of topic must differ from mqttclient (#14019)

Fixed

• EZOO2 sensor message format (#14000)
• ESP32 Webcam exception during flashwrites
• ESP32 LedPwmMode exception (#14073)
• ESP32 Compile error when I2S_Audio is enabled (#14095)

[10.1.0] 20211208

• Release Noelle

Added

• Berry added tcpclient

[10.0.0.4] 20211208

Added

• (Internal) Support for FUNC_BUTTON_MULTI_PRESSED in (light)drivers
• Support for GPE Multi color smart light as sold by Action in the Netherlands
• Support for 74xx595 8-bit shift registers (#13921)

Changed

• (Internal) Range conversion edge values
• NimBLE to v.1.3.3
• MQTT TLS dual mode (CA or fingerprint) in same firmware, SetOption132 1 to force fingerprint
• Toolchains for ESP32x changed from 8.4.0-2021r1 to 8.4.0-2021r2

Fixed

• Tuya dimmer range issue (#13849)
• BLE Memory leak with update NimBLE v.1.3.1 to v.1.3.3
• Compile error BLE EQ3 driver with core 2.0.x (#13948)

[10.0.0.3] 20211130

Added

• Shutter support for venetian blinds with tilt control
• ESP32 Autoconfiguration
• ESP32 fix leftover GPIO configuration after restart
• ESP32 Proof of Concept Sonoff SPM with limited functionality (switching and energy monitoring) (#13447)
• WS2812 scheme 13 stairs effect (#13595)
• ESP32 Preliminary support for Tasmota Apps (.tapp extensions)
• ESP32 Berry support for neopixel (WS2812, SK6812)
• Command IfxPeriod to overrule Teleperiod for Influx messages (#13750)
• ESP32 OTA over HTTPS
• ESP32 Berry import re regex module
• ESP32 HTTPS support to WebQuery

Changed

• ESP8266 Gratuitous ARP enabled and set to 60 seconds (#13623)
• Removed ILI9488 driver in favor of Universal Display Driver
• IRremoteESP8266 library from v2.7.20 to v2.8.0 (#13738)
• Ethernet hostname ending in _eth to -eth according to RFC952
• ESP32 core library from v2.0.1 to v2.0.1.1 (#13768)

Fixed

• ESP32 analog NTC temperature calculation (#13703)
• ESP32 ethernet broken by core 2.x
• ESP32 I2C clock stretch issue (#13768)

Removed

• ILI9488 driver in favour of Universal Display driver (#13719)

[10.0.0.2] 20211113

Added

• Support for HDC2010 temperature/humidity sensor by Luc Boudreau (#13633)

Breaking Changed

• ESP32-S2 TSettings memory usage fixed to 4096 bytes regression from v9.5.0.8

Changed

• ESP32 core library from v1.0.7.5 to v2.0.1

[10.0.0.1]

Added

• Berry add module python_compat to be closer to Python syntax (#13428)
• 1 second heartbeat GPIO
• Command TcpConfig for TCPBridge protocol configuration (#13565)

Changed

• File editor no-wrap (#13427)
• ESP32 core library from v1.0.7.4 to v1.0.7.5
• ESP32-C3 core library from v2.0.0-post to v2.0.1-rc1

Fixed

• Initial reset RTC memory based variables like EnergyToday and EnergyTotal
• ESP32 Telegram compile error (#13435)
• SML compile error (#13441)
• GUI checkbox MQTT TLS not saved regression from v9.2.0.3 (#13442)
• Discovery of shutters (#13572)
• ESP32-C3 OneWire as used by DS18x20 (#13583)

[10.0.0] 20211019

• Release Norman

[9.5.0.9] 20211019

Added

• Command SetOption129 1 to enable split total energy results (#13030)
• Command SetOption130 1 adding heap size (and ESP32 fragmentation) to logging timestamp for debugging
• Commands EnergyTotal<phase>, EnergyToday<phase> and EnergyYesterday<phase> to (re)set energy values
• Commands EnergyUsage and EnergyExport to (re)set energy usage and export values
• Berry add module import persist
• Support for BL0942 energy monitor (#13259)
• Support for HM330X SeedStudio Grove Particule sensor (#13250)

Breaking Changed

• ESP32 LVGL updated to v8.0.2

Changed

• Removed command EnergyReset as it is replaced by new commands
• Files starting with underscore in file system are no more hidden
• ESP32 Memory display to exclude IRAM (i.e. less by 40-50KB) (#13294)
• LVGL Berry namespace lv.* added and removed lv_* constants

Fixed

• ESP32 restore GPIO16/17 if no PSRAM was found regression from v9.5.0.3
• Restore functionality as documented when both GPIO_LED1 and GPIO_LED2 are used regression from v8.5.0 (#13368)

[9.5.0.8] 20210927

Added

• Command WebGetConfig <url> if #define USE_WEBGETCONFIG is enabled to restore/init configuration from external webserver (#13034)
• Berry class webclient for HTTP/HTTPS requests
• Support for ESP32-S2 GPIOs
• ESP32 add GPIO 6/7/8/11 to template and remove GPIO 28-31 (remapping so backwards compatible)
• Crash recorder Status 12 for ESP32/ESP32-S2/ESP32-C3, supporting Esp-idf 3.3/4.4
• Support for ESP32/ESP32-S2 DAC gpio via Berry
• Berry support for Serial
• Support for Sensirion SCD40/SCD41 CO2 sensor (#13139)
• Support for BL0939 energy monitor as used in ESP32 based Sonoff Dual R3 V2 Pow (#13195)
• Command WebQuery <url> GET|POST|PUT|PATCH [<headers>] <body> to extent HTTP requests (#13209)
• Berry print stack trace when exception, more detailed with line numbers if #define USE_BERRY_DEBUG

Changed

• M5 Stack Core2 uses UNIVERSAL_DISPLAY with enabled LVGL as default now
• DisplayDimmer has now range 0..100 instead of 0..15
• Minimum PWM Frequency lowered to 2Hz on ESP32 (#13123)
• Use Tasmota Arduino Core32 1.0.7.4 for ESP32 builds (#13154)
• Shrinked Webcam build, uses now USE_TASMOTA_DISCOVERY (#13148)
• Berry revamped energy module to expose all C variables to Berry (read/write)

Fixed

• OpenTherm invalid JSON (#13028)
• ESP32 crash when PSRAM is absent and BOARD_HAS_PSRAM set (#13037)
• MQTT TLS related connection timing errors (#13033)

[9.5.0.7] 20210901

Added

• Turn HTTP API (command SetOption128 1) default on for backward compatibility
• Support for IEM3155 Wattmeter (#12940)
• Berry support for vararg
• Command Subscribe2 ... to subscribe to a MQTT topic without appended "/#" (#12858)
• Support for Hydreon RG-15 Solid State Rain sensor (#12974)
• Support for IKEA VINDRIKTNING particle concentration sensor (#12976)
• Berry support for Curve 25519 EC crypto
• Command SetOption2 1 to enable display of global temperature/humidity/pressure info to JSON sensor message

Changed

• Shelly EM template needs to use GPIO ADE7953_IRQ_2
• IRremoteESP8266 library from v2.7.19 to v2.7.20

Fixed

• WDT reset on shutters with stepper motors during deceleration (#12849)
• Shelly 2.5 negative power values on relay 1 regression from 9.5.0.5
• Wiegand support for keypad zero key in single key mode using SetOption124 1 (#12960)
• Hass and Tasmota discovery prefix topic notifications (#12972)
• Unable to disable MusicSync mode on Sonoff L1 Lite regression from 9.3.0 (#12930)
• Shelly Dimmer 2 Energy usage (#12815)
• Sonoff L1 (lite) smoother color transitions

[9.5.0.6] 20210820

Added

• Version bump to monitor possible HTTP issues related to SetOption128

Changed

• Berry now compiling in strict mode to catch more bugs

Fixed

• ESP32-C3 PWM5

[9.5.0.5] 20210815

Added

• Inital support for Wi-Fi extender (#12784)
• Neopool commands NPPHRes, NPCLRes and NPIonRes (#12813)
• Support for (Yeelight) Mi Desk Pro using binary tasmota32solo1.bin
• Initial support for influxdb using #define USE_INFLUXDB and several Ifx commands
• Command SetOption128 1 disabling web referer check default blocking HTTP web commands (#12828)

Changed

• NeoPixelBus library from v2.6.3 to v2.6.7
• Make Sonoff L1 MusicSync persistent (#12008)
• Relax NTP poll if no ntpserver can be resolved by DNS
• Move firmware binaries to https://github.com/arendst/Tasmota-firmware/tree/main/release-firmware
• Default disable CORS for enhanced security and provide user compile option #define USE_CORS (#12827)
• Prometheus: All metrics are prefixed with tasmota_ (#12842) Memory metrics have been cleaned up to work consistently between ESP8266 and ESP32 The device name is reported as an info metric

Fixed

• Neopool communication error (#12813)
• Negative power values for ADE7953 based devices like Shelly EM (#12874)

[9.5.0.4] 20210801

Added

• Support for second DNS server
• Optional IP filter to command TCPStart (#12806)

Changed

• ESP8266Audio library from v1.5.0 to v1.9.2

[9.5.0.3] 20210729

Added

• Command SetSensor1..127 0|1 to globally disable individual sensor driver
• Support for CAN bus and Freedom Won Battery Management System by Marius Bezuidenhout (#12651)
• Berry ESP32 support for I2S audio mp3 playback
• Berry add module introspect
• Berry add tasmota.wifi() and tasmota.eth()
• LVGL new widget lv_wifi_bars

Changed

• ESP32 core library from v1.0.7.1 to v1.0.7.3
• Disable PSRAM on unsupported hardware
• Replace spaces by hyphens in final hostname (#12710)
• Message Upload buffer miscompare into Not enough space
• ESP32 remove GPIO initialization to INPUT from not used GPIOs to allow JTAG support

Fixed

• Discovery fails when using %hostname% in a topic (#12710)
• ESP32-Solo OTA upgrade
• ESP32 buzzer in PWM mode exception (#12717)

[9.5.0.2] 20210714

Added

• Initial support for Tasmota Mesh (TasMesh) providing node/broker communication using ESP-NOW (#11939)
• MQTT minimum password length restriction in GUI (#12553)
• Command SetOption127 1 to force Wi-Fi in no-sleep mode even if Sleep 0 is not enabled
• Support for Technoline WS2300-15 Anemometer (#12573)
• Support for Telaire T6700 Series CO2 sensor by Alexander Savchenko (#12618)

Changed

• ESP32 core library from v1.0.7 to v1.0.7.1
• IRremoteESP8266 library from v2.7.18 to v2.7.19
• ESP32 Ethernet Phy Type information to IDF v3+
• Allow buttons to work in AP normal mode (#12518)
• Enable Ping and rule features for any device compiled with more than 1M flash size (#12539)
• ESP32 internal sensor driver id moved from 87 to 127
• Extended supported sensor driver range to 128

Fixed

• ESP32-C3 settings layout for configuration backup and restore
• ESP32 core v2.0.0 setting hostname
• Berry button handlers and error messages (#12521)
• Scripter and Display MQTT errors due to MQTT_DATA move to String (#12525)
• Scripter moving average and sml input validation (#12541)
• Zigbee Hue angle encoding (#12545)
• AM2320 value reporting (#12552)
• Exception 28 when unable to send MQTT message and a topic name without a slash '/' (#12555)
• Wi-Fi initial setup workaround for 11n only routers (#12566)
• ESP32 do not use chip temperature sensor as global temperature if external temperature sensor is used (#12630)

[9.5.0.1] 20210701

Added

• Berry ESP32 partition manager (#12465)
• Rule event support as JSON payload (#12496)
• Support for AM2320 Temperature and Humidity Sensor by Lars Wessels (#12485)

Changed

• ESP32 core library from v1.0.6 to v1.0.7
• Speed up initial GUI console refresh
• Enable UFILESYS, GUI_TRASH_FILE and GUI_EDIT_FILE for any device compiled with more than 1M flash size
• Simplified configuration for ir-full and removal of tasmota-ircustom
• Refactor platformio (#12442)

Fixed

• ESP32 Webcam add boundary marker before sending mjpeg image (#12376)
• DDS238-2 wrong reactive power value (#12283)
• NO VALID JSON regression from may 4th (#12440)
• Telegram response decoding stopped working after 20210621 and exception on long result message (#12451)
• Neopool compile error on DEBUG_TASMOTA_SENSOR (#12464)

[9.5.0] 20210617

• Release Michael (Rossi)

[9.4.0.6] 20210617

Added

• Command MqttWifiTimeout 100..20000 to control MQTT Wi-Fi connection timeout default set to 200 mS (#12222)

[9.4.0.5] 20210615

Added

• Preliminary support for Esp32C3 - RiscV based

Changed

• NeoPixelBus library from v2.6.1.4 to v2.6.3 stage
• Allow longer MQTT response messages by removing fixed memory buffer with size 1040 to heap allocated buffer
• Command Timers layout of JSON message changed to single line
• Command Gpio layout of JSON message changed to single line
• Command Modules layout of JSON message changed to single line
• I2C extended MPU6886 to also support MPU9250 (found in Legacy M5Stack Fire)
• ESP32 increase log buffer from 4k to 6k to support longer messages
• Move Settings from DRAM to heap
• WifiManager save Wi-Fi configuration from settings, do it only once (#12242)
• Improving SI7021 reading reliability by adjusting timers (#12256)
• Refactor ESP32 partition selection, now via boards (#12257)
• Refactor platformio configurations by Jason2866
• Use correct template for Home Assistant light (#12317)

[9.4.0.4] 20210610

Added

• Version bump to signal new features to Hass
• Command Status0 providing all status information on a single line
• LVGL support for PNG images (#12148)
• Update Sugar Valley Neopool driver (#12171)
• Acer projector support (#12190)
• I2S and Interrupt GPIO types (#12192)
• Update OpenTherm driver (#12195)
• Support for BM8563 RTC chip (I2C) found in M5Stack Core2 and M5StickC (#12199)
• Command TuyaSend5 for hex string (#12211)
• Extend command Wifi with Wi-Fi Mode Control (#12292)

Changed

• IRremoteESP8266 library from v2.7.16 to v2.7.18

Fixed

• PING race condition breaks JSON in rule (#12106)
• Support Tuya powermeter >6500W (#12115)
• Zigbee max end-device (#12159)
• Prevent keep state MCP230xx output fast toggle on reboot (#12264)
• Tuya data type 2 read as 32 bit integer (instead of 16 bit) (#12282)

[9.4.0.3] 20210515

Added

• Make Telegram command TmState persistent (#11965)
• Zigbee firmware for Tube's Zigbee coordinator based on EFR32 and ESP32
• Zigbee firmware 6.7.9 for Sonoff ZBBridge
• Defines USER_RULE1, USER_RULE2 and USER_RULE3 to store rules at compile time
• Define USER_BACKLOG to store commands at compile time to be executed at firmware load or when executing command reset
• LVGL support for 3 buttons as rotary encoder (#12035)
• LVGL support for touchscreen (#12039)
• Allow home assistant discovery of MCP2300xx output as relay (#12037)
• LVGL support for TrueType fonts via FreeType library (#12087)
• LVGL support for PSRAM (#12062)
• Support for voltage and current monitoring when using Shelly dimmer 2 hardware (#11988)
• Support for Azure Device Provisioning Service for IoT Hub (#12056)
• Commands Color2 and Dimmer4 to allow retaining brightness ratio between white and color channels when setting dimmer for linked lights (#12072)
• Show new IP after the Wi-Fi Initial Config (#12091)

Fixed

• Avoid erasing of Zigbee data if zigbee is not started (#11961)
• Zigbee XModem retries (#11967)
• Teleinfo standard mode and blacklist feature crash (#11991)
• ESP32 Hue light (#12005)
• Map received CCT channels back in DevGroups (#12044)
• Increase TLS minimum stack thunk to 3800 bytes (#12063)
• Delay discovery of PZEM sensors (#12076)

Changed

• Shelly Dimmer 1 and 2 stm32 firmware from v51.5 to v51.6

[9.4.0.2] 20210430

Added

• Initial support for optional Template JSON fieldpair "CMND":"<any template related command>|<any template related command>|..." (#11788)
• ESP32 pulldown buttons Button_d and Button_id and switches Switch_d (#10814)
• Support for MQTT using Azure IoT Hub by Kevin Saye (#11906)
• Zigbee binary supporting cc25xx hardware on 4M flash hardware (#11872)

Fixed

• Wrong flash size detection when saving Zigbee device information on ESP8266 (#11870)
• Prometheus metrics parse error on DS18x20 (#11931)
• DS18x20 name search id (#11958)

[9.4.0] 20210423

• Release Leslie

[9.4.0.1] 20210423

Added

• Command Wifi 0/1 for ESP8266 to turn Wi-Fi Off and On. When Wi-Fi is Off it is always returned On after a restart except for a wake-up from deepsleep (#11839)

Changed

• Zigbee refactored storage for device configuration and device last known data (#11838)

Fixed

• Command Power should not reset pulsetime (#11805)
• Teleperiod rule handling regression from v9.3.1.2 (#11851)

[9.3.1.4] 20210422

Added

• Command TuyaTempSetRes 0..3 to control Tuya Temperature Set Resolution (#11781)
• ESP32 support for LVGL 7.11 with Berry binding by Stephan Hadinger (#11789)
• Add Input GPIO type with no default action, to be read via Berry

[9.3.1.3] 20210419

Added

• Optional GUI file editor enabled with define GUI_EDIT_FILE by barbudor (#11668)
• Initial support for universal display driver UDisplay by Gerhard Mutz. Enable by selecting any GPIO as Option A3 (#11665)

Breaking Changed

• ESP32 partition layout changed to accomodate more file space on most and more code space on core2 and odroid-go (#11746)

Changed

• In tasmota-sensors.bin enabled support for VL53L0X and disabled TSL2561 (#11711)
• Add HLW8012/BL0937 average pulse calculation by Alex Lovett (#11722)
• Redesigned initial GUI Wi-Fi configuration by Adrian Scillato (#11693)
• Redesigned GUI by moving non-configuration buttons from Configuration to new submenu Consoles

Fixed

• Telegram chat id incorrect size (#11660)
• KNX energy yesterday (#11718)

[9.3.1.2] 20210413

Added

• Commands MqttKeepAlive 1..100 to set Mqtt Keep Alive timer (default 30) and MqttTimeout 1..100 to set Mqtt Socket Timeout (default 4) (#5341)
• Commands DisplayType to select sub-modules where implemented and DisplayInvert to select inverted display where implemented
• Command SerialBuffer 256..520 to change hardware serial receive buffer size from default (256) to max local buffer size (520) (#11448)
• Command SetOption126 1 to enable DS18x20 arithmetic mean over teleperiod for JSON temperature based on (#11472)
• Support for TM1638 seven segment display by Ajith Vasudevan (#11031)
• Support for MAX7219 seven segment display by Ajith Vasudevan (#11387)
• Support for Frequency monitoring and zero-cross detection on CSE7761 (Sonoff Dual R3)
• ESP32 support for internal Hall Effect sensor connected to both GPIO36 and GPIO39 only
• Support for multiple CCS811 sensors with baseline control (USE_CCS811_V2) by clanganke (#10858)
• Berry add gpio module
• Berry add light module
• Support for dummy energy monitor using user values set by commands VoltageSet, CurrentSet, PowerSet and FrequencySet. Enable by selecting any GPIO as Option A2 (#10640)
• Command Backlog0 to allow execution of following commands without delay
• Tasmota discovery as alternative to Home Assistant discovery using define USE_TASMOTA_DISCOVERY

Changed

• PubSubClient library from EspEasy v2.7.12 to Tasmota v2.8.12
• IRremoteESP8266 library from v2.7.15 to v2.7.16
• ESP32 core library from v1.0.5 to v1.0.6
• Limit number of relay/button columns in GUI to 8 (#11546)
• ADC range result from int to float using command FreqRes for decimal resolution selection (#11545)
• Teleinfo, if raw mode selected also return telemety values in SENSOR data
• Removed overtemp detection on external energy monitoring devices (#11628)

Fixed

• HC-SR04 on ESP32 release serial interface if not used (#11507)
• Teleinfo, if raw mode selected also always update total energy calculations
• Alexa discovery for ZBBridge (#11576)
• Alexa discovery in hue emulation (#11415)

[9.3.1.1] 20210320

Added

• Support for CSE7761 energy monitor as used in ESP32 based Sonoff Dual R3 Pow (#10793)
• Command Sensor80 1 <0..7> to control MFRC522 RFID antenna gain from 18dB (0) to 48dB (7) (#11073)
• Allow MCP230xx pinmode from output to input (#11104)
• SML VBUS support (#11125)
• Support for NEC and OPTOMA LCD/DLP Projector serial power control by Jan Bubík (#11145)
• Support for XPT2046 touch screen digitizer on ILI9341 display by nonix (#11159)
• Berry improvements (#11163)
• Support for zigbee lumi.sensor_wleak (#11200)
• Crash protection in ext_vnsprintf_P (#11202)
• Extent compile time SetOptions support (#11204)
• ESP32 Extent BLE (#11212)
• ESP32 support for WS2812 hardware driver via RMT or I2S
• ESP32 support for secondary I2C controller
• Support for MPU6886 on primary or secondary I2C bus

Changed

• ESP32 core library from v1.0.5-rc6 to v1.0.5
• TasmotaSerial library from v3.2.0 to v3.3.0
• TuyaMcu dimmer timeout (#11121)
• Rename epaper 42 commands (#11222)
• DeepSleep announcement topic (#11223)

Fixed

• PN532 on ESP32 Serial flush both Tx and Rx buffers (#10910)
• Light scheme related color changes (#11041)
• Refactor acceleration function for shutter stepper and servo (#11088)
• LM75AD detection on different addresses (#11096)
• Timer loop when console is scrolled up regression from v9.3.0 (#11108)
• Display exception when no file system is present (#11125)
• Scripter and SML fixes (#11150)
• Zigbee exception when bad frame is received (#11192)
• ESP32 flash script for Odroid and Core2 (#11227)
• ESP32 WS2812 bitbang support (#11248)
• DS18x20 driver timing issue (#11270)

[9.3.1] 20210223

• Release Kenneth

[9.3.0.1] 20210223

Added

• Animate PWM dimmer brightness LEDs during transitions and with variable brightness (#11076)
• Commands StateRetain and InfoRetain (#11084)

Changed

• Remove the need to start filenames with a slash (/) in Ufs commands
• Removed command VirtualCT as synonym for SetOption106 (#11049)

Fixed

• Web request accepts wrong password (#11039)
• Ili1942 driver (#11046)
• ESP32 Mi32 driver (#11048)
• Shutter driver (#11055)
• TM1637 driver now needs TM1637 CLK and TM1637 DIO to enable (#11057)
• Sml driver (#11082)
• Ezo drivers (#11083)

[9.3.0] 20210219

• Release Kenneth

[9.2.0.7] 20210219

Added

• Support for Device Groups Device Map (#10898)
• Support for Eastron SDM72D-M three phase 100A Modbus energy meter (#10862)
• Support for Frysk language translations by Christiaan Heerze
• ESP8266 Fallback to *.bin.gz binary when OTA upload of *.bin binary fails
• Berry language improved Tasmota integration
• Berry file system support
• Filesystem commands Ufs, UfsType, UfsSize, UfsFree, UfsDelete, UfsRename and UfsRun
• Support for filesystem autoexec.bat to execute sequential commands like backlog
• Support for TM1637 seven segment display by Ajith Vasudevan (#10889)

Changed

• IRremoteESP8266 library from v2.7.14 to v2.7.15
• NeoPixelBus library from v2.6.0 to v2.6.1.4
• ILI9341 library from Adafruit_ILI9341-1.2.0-Tasmota-1.0 to ILI9341-gemu-1.0

[9.2.0.6] 20210210

Changed

• Remove support for direct migration from versions before v8.1.0 (Doris)
• ESP32 Increase number of switch GPIOs from 8 to 28
• ESP32 Increase number of interlock groups from 4 to 14
• Increase number of button GPIOs from 4 to 8
• Preview of Berry language for Tasmota32

[9.2.0.5] 20210205

Changed

• ESP32 increase number of relay GPIOs from 8 to 28

[9.2.0.4] 20210204

Added

• Function AddLog to provide logging for up to 128 (LOGSZ) characters to save stack space
• Commands ChannelRemap, MultiPWM, AlexaCTRange, PowerOnFade, PWMCT, WhiteBlend and VirtualCT as synonyms for SetOption37, 68, 82, 91, 92, 105 and 106
• Commands ZbNameKey, ZbDeviceTopic, ZbNoPrefix, ZbEndpointSuffix, ZbNoAutoBind and ZbNameTopic as synonyms for SetOption83, 89, 100, 101, 110 and 112
• Commands ZbNoAutoBind, ZbReceivedTopic and ZbOmitDevice as synonyms for SetOption116, 118 and 119
• Commands BuzzerActive and BuzzerPwm as synonyms for SetOption67 and 111
• Support for ESP32 Module 5 Wireless Tag Eth01 (#9496)
• Support trailing silence in buzzer tune (#10694)
• Command L1MusicSync <0|Off>|<1|On>|<2|Toggle>, 1..10, 1..100> to control Sonoff L1 Music Sync mode sensitivity and speed (#10722)
• Command Speed2 to control a once off fade (#10741)
• Zigbee command SetOption120 1 or ZbEndpointTopic 1 to add the endpoint as suffix in topic when using SetOption89 1
• Zigbee command ZbScan to do an energy scan on each radio channel

Changed

• Maximum chars in AddLog_P logging restored from 128 to 700 (MAX_LOGSZ) to solve broken error messages

[9.2.0.3] 20210122

Added

• Support for time proportioned (#define USE_TIMEPROP) and optional PID (#define USE_PID) relay control (#10412)
• Support rotary encoder on Shelly Dimmer (#10407)
• Command SetOption43 1..255 to control Rotary step (#10407)
• Support for BS814A-2 8-button touch buttons by Peter Franck (#10447)
• Support for up to 4 I2C SEESAW_SOIL Capacitance & Temperature sensors by Peter Franck (#10481)
• ESP8266 Support for 2MB and up linker files with 1MB and up LittleFS
• ESP32 support for TLS MQTT using BearSSL (same as ESP8266)
• Support for 24/26/32/34 bit RFID Wiegand interface (D0/D1) by Sigurd Leuther (#3647)
• Compile time option USE_MQTT_TLS_DROP_OLD_FINGERPRINT to drop old (less secure) TLS fingerprint
• Command SetOption40 0..250 to disable button functionality if activated for over 0.1 second re-introduced
• Support for SM2135 current selection using GPIO SM2135 DAT index (#10634)
• Support for ESP32 Module 7 M5stack core2 16MB binary tasmota32-core2.bin (#10635)
• Support for Sugar Valley NeoPool Controller by Norbert Richter (#10637)
• Rule trigger string comparisons for EndsWith $>, StartsWith $< and Contains $| (#10538)
• Support for TOF10120 time of flight sensor by Cyril Pawelko (#10190)

Breaking Changed

• ESP32 switch from default SPIFFS to default LittleFS file system loosing current (zigbee) files
• ESP8266 until now NOT SUPPORTED linker files 2MB and up. Current settings will be overwritten once LittleFS is enabled

Changed

• Force initial default state SetOption57 1 to scan Wi-Fi network every 44 minutes for strongest signal (#10395)
• Command Sleep 0 removes any sleep from Wi-Fi modem except when ESP32 BLE is active
• PubSubClient MQTT_SOCKET_TIMEOUT from 15 to 4 seconds
• Domoticz fixed 2 decimals resolution by user selectable TempRes, HumRes and PressRes resolutions

[9.2.0.2] 20210105

Added

• Support for ESP32 Module 3 Odroid Go 16MB binary tasmota32-odroidgo.bin (#8630)
• Command CTRange to specify the visible CT range the bulb is capable of (#10311)
• Command VirtualCT to simulate or fine tune CT bulbs with 3,4,5 channels (#10311)
• Command SetOption118 1 to move ZbReceived from JSON message and into the subtopic replacing "SENSOR" default (#10353)
• Command SetOption119 1 to remove the device addr from json payload, can be used with zb_topic_fname where the addr is already known from the topic (#10355)
• Command RuleTimer0 to access all RuleTimers at once (#10352)
• SPI display driver SSD1331 Color oled by Jeroen Vermeulen (#10376)
• IRremoteESP8266 library from v2.7.13 to v2.7.14
• Rotary No Pullup GPIO selection Rotary A/B_n (#10407)

Breaking Changed

• Replaced MFRC522 13.56MHz rfid card reader GPIO selection from SPI CS by RC522 CS
• Replaced NRF24L01 GPIO selection from SPI CS by NRF24 CS and SPI DC by NRF24 DC
• Replaced ILI9341 GPIO selection from SPI CS by ILI9341 CS and SPI DC by ILI9341 DC
• Replaced ST7789 GPIO selection from SPI CS by ST7789 CS and SPI DC by ST7789 DC
• Replaced ILI9488 GPIO selection from SPI CS by ILI9488_CS
• Replaced EPaper29 GPIO selection from SPI CS by EPaper29 CS
• Replaced EPaper42 GPIO selection from SPI CS by EPaper42 CS
• Replaced SSD1351 GPIO selection from SPI CS by SSD1351 CS
• Replaced RA8876 GPIO selection from SPI CS by RA8876 CS

Changed

• Maximum chars in AddLog_P logging reduced from 700 to 128 (LOGSZ) to enhance stability
• Disabled USE_LIGHT light support for ZBBridge saving 17.6kB (#10374)

[9.2.0.1] 20201229

Added

• Milliseconds to console output (#10152)
• Support for P9813 RGB Led MOSFET controller (#10104)
• Support for GPIO option selection
• Gpio Option A1 enabling PWM2 high impedance if powered off as used by Wyze bulbs (#10196)
• Support for FTC532 8-button touch controller by Peter Franck (#10222)
• Support character # to be replaced by space-character in command Publish topic (#10258)
• BSSID and Signal Strength Indicator to GUI Wi-Fi scan result (#10253)
• Support for Afrikaans language translations by Christiaan Heerze
• Support for IR inverted leds using #define IR_SEND_INVERTED true (#10301)
• Support for disabling 38kHz IR modulation using #define IR_SEND_USE_MODULATION false (#10301)
• Support for SPI display driver for ST7789 TFT by Gerhard Mutz (#9037)

Changed

• Logging from heap to stack freeing 700 bytes RAM

Fixed

• Redesign syslog and mqttlog using log buffer (#10164)
• Shutter stop issue (#10170)
• Scripter script_sub_command (#10181)
• Scripter JSON variable above 32 chars (#10193)
• Shelly Dimmer power on state (#10154, #10182)
• Wemo emulation for single devices (#10165, #10194)
• ESP32 LoadStoreError when using #define USER_TEMPLATE (#9506)
• Compile error when #ifdef USE_IR_RECEIVE is disabled regression from 9.1.0.2
• Prometheus memory leak (#10221)

[9.2.0] 20201221

Fixed Backported

• Shutter stop issue (#10170)
• Scripter script_sub_command (#10181)
• Scripter JSON variable above 32 chars (#10193)
• Shelly Dimmer power on state (#10154, #10182)
• Wemo emulation for single devices (#10165, #10194)
• ESP32 LoadStoreError when using #define USER_TEMPLATE (#9506)
• Compile error when #ifdef USE_IR_RECEIVE is disabled regression from 9.1.0.2

[9.2.0] 20201216

• Release Julie

[9.1.0.2] 20201216

Added

• KNX read reply for Power (#9236, #9891)
• Zigbee persistence of device/sensor data in EEPROM (only ZBBridge)
• Support for common anode sevenseg displays by adding #define USE_DISPLAY_SEVENSEG_COMMON_ANODE by Ken Sanislo (#9963)
• Support for multiple WeMo devices by Magic73 (#9208)
• Fallback NTP server from x.pool.ntp.org if no ntpservers are configured
• TyuaMcu update 2/3 by Federico Leoni (#10004)
• Optional CCloader support for CC25xx Zigbee or CC26xx BLE by Christian Baars (#9970)
• Command RfProtocol to control RcSwitch receive protocols by BBBits (#10063)
• Zigbee better support for Tuya Protocol (#10074)
• Support for SPI connected MFRC522 13.56MHz rfid card reader (#9916)
• Letsencrypt R3 in addition to X3 CA (#10086)
• Zigbee add visual map of network
• Command SetOption117 1 for light fading to be fixed duration instead of fixed slew rate (#10109)
• Support ESP32 SPIFFS for internal use

Breaking Changed

• KNX DPT9 (16-bit float) to DPT14 (32-bit float) by Adrian Scillato (#9811, #9888)

Changed

• Core library from v2.7.4.7 to v2.7.4.9
• Shelly Dimmer fw upgrade using WebGUI Firmware Upgrade and file from folder tools/fw_shd_stm32/
• MQTT Wi-Fi connection timeout from 5000 to 200 mSec (#9886)
• Platformio compiler option -free -fipa-pta enabled (#9875)
• IRremoteESP8266 library from v2.7.12 to v2.7.13
• Shelly Dimmer 1 and 2 stm32 firmware from v51.4 to v51.5
• Force bigger Thunk Stack if 4K RSA even without EC ciphers (#10075)
• mDNS has been disabled from all pre-compiled binaries to allow new features

Fixed

• KNX ESP32 UDP mulicastpackage (#9811)
• Command gpio using non-indexed functions regression from v9.1.0 (#9962)
• ESP32 TasmotaClient firmware upgrade (#9218)
• Reset to defaults after 6 hours of DeepSleep (#9993)
• Backlog timing wraparound (#9995)
• First LED in addressable string does not fade when using scheme (#10088)
• Improved Opentherm error handling (#10055)
• Platformio compiler option no target align removed fixing hardware watchdog exceptions
• Shutter motordelay stop issue (#10033)
• Shutter fix overflow on runtime over 100 seconds (#9800)
• ESP32 CC2530 heap corruption (#10121)
• ESP32 Analog input div10 rule trigger (#10149)

Removed

• PN532 define USE_PN532_CAUSE_EVENTS replaced by generic rule trigger on pn532#uid=

[9.1.0.1] - 20201116

Added

• Zigbee support for Mi Door and Contact (#9759)
• Zigbee alarm persistence (#9785)
• Support for EZO PMP sensors by Christopher Tremblay (#9760)
• Commands TuyaRGB, TuyaEnum and TuyaEnumList (#9769)
• Zigbee command ZbInfo and prepare support for EEPROM
• Support for AS608 optical and R503 capacitive fingerprint sensor
• Command SetOption115 1 to enable ESP32 MiBle
• Zigbee command ZbLeave to unpair a device
• Command SetOption116 1 to disable auto-query of zigbee light devices (avoids network storms with large groups)
• Support for Shelly Dimmer 1 and 2 by James Turton (#9854)
• IRremoteESP8266 library from v2.7.11 to v2.7.12

Changed

• Core library from v2.7.4.5 to v2.7.4.7
• Platformio compiler option no target align enabled (#9749)
• Consolidate AddLog_P into AddLog_P2 and rename to AddLog_P
• Sonoff L1 color up scaling and color margin detection (#9545)

Fixed

• NTP fallback server functionality (#9739)
• Telegram group chatid not supported (#9831)
• KNX buttons, switches and sensors detection regression from v9.1.0 (#9811)
• GUI MqttUser and MqttPassword updates when TLS is compiled in (#9825)

Removed

• Version compatibility check

[9.1.0] 20201105

• Release Imogen

[9.0.0.3] - 20201105

Added

• TLS in binary tasmota-zbbridge (#9635)
• Support for EZO O2 sensors by Christopher Tremblay (#9619)
• Support for EZO PRS sensors by Christopher Tremblay (#9659)
• Support for EZO FLO sensors by Christopher Tremblay (#9697)
• Support for EZO DO sensors by Christopher Tremblay (#9707)
• Support for EZO RGB sensors by Christopher Tremblay (#9723)
• Zigbee reduce battery drain (#9642)
• Zigbee command ZbMap to describe Zigbee topology (#9651)
• Zigbee command ZbOccupancy to configure the time-out for PIR
• Command Gpios 255 to show all possible GPIO configurations
• Command SwitchText to change JSON switch names by barbudor (#9691)
• Command SetOption114 1 to detach Switches from Relays and enable MQTT action state for all the SwitchModes returning {"Switch1":{"Action":"ON"}}
• Command DimmerStep 1..50 to change default dimmer up and down step of 10% by James Turton (#9733)
• HM10 Beacon support and refactoring by Christian Baars (#9702)
• Support for Hass discovery of TuyaMcu and Sonoff Ifan by Federico Leoni (#9727)
• Initial support for iBeacons (Sensor52) on ESP32 using internal BLE by rvbglas (#9732)

Changed

• PlatformIO library structure redesigned for compilation speed by Jason2866
• Zigbee flash storage refactor adding commands ZbProbe, ZbStatus2 and ZbRestore (#9641)
• Default otaurl in my_user_config.h to http://ota.tasmota.com/tasmota/release/tasmota.bin.gz
• When SetOption73 1 JSON result from {"ACTION":"SINGLE"} to {"Button1":{"Action":"SINGLE"}}

Fixed

• Rule Break not working as expected when ONCE is enabled (#9245)
• Rule expressions using mems corrupts character pool (#9301)
• Button press rules regression introduced by #9589 (#9700)
• Rule handling of JSON null regression from v8.5.0.1 (#9685)
• Arilux RF remote detection regression from v8.3.0

Removed

• Auto output selection of decimal or hexadecimal data based on user input. Now only based on SetOption17

[9.0.0.2] - 20201025

Added

• Support for Vietnamese language translations by Tâm.NT
• Support for timers in case of no-sunset permanent day by cybermaus (#9543)
• Command NoDelay for immediate backlog command execution by Erik Montnemery (#9544)
• Command SwitchMode 15 sending only MQTT message on switch change (#9593)
• Command ShutterChange to increment change position (#9594)
• Command SetOption113 1 to set dimmer low on rotary dial after power off
• Support for EZO Ph and ORP sensors by Christopher Tremblay (#9567)
• Support for EZO RTD sensors by Christopher Tremblay (#9585)
• Support for EZO HUM sensors by Christopher Tremblay (#9599)
• Support for EZO EC sensors by Christopher Tremblay (#9613)
• Support for EZO CO2 sensors by Christopher Tremblay (#9619)
• On ZigbeeBridge support for glowing led when permit join is active (#9581)
• Support for PWM Dimmer multi-press and ledmask (#9584)
• Make button press rules override PWM Dimmer functions (#9589)
• Support for fixed output Hi or Lo GPIO selection
• ESP32 support for Wireless-Tag WT32-ETH01 (#9496)
• ESP32 MI32 Beacon support, RSSI at TELEPERIOD, refactoring by Christian Baars (#9609)

Changed

• Command Gpio17 replaces command Adc
• Command Gpios replaces command Adcs
• Management of serial baudrate (#9554)
• TLS fingerprint #define MQTT_FINGERPRINT from string to hexnumbers (#9570)
• Rotary driver adjusted accordingly if Mi Desk Lamp module is selected (#9399)
• Tasmota Arduino Core v2.7.4.5 allowing webpassword over 47 characters (#9687)
• Webserver code optimizations (#9580, #9590)

Fixed

• Convert AdcParam parameters from versions before v9.0.0.2
• Telegram message decoding error regression from v8.5.0.1
• Correct Energy period display shortly after midnight by gominoa (#9536)
• Rule handling of Var or Mem using text regression from v8.5.0.1 (#9540)
• TuyaMcu energy display regression from v8.5.0.1 (#9547)
• Tuyamcu dimmers MQTT topic (#9606)
• MQTT data corruption on MQTTLog 4 (#9571)
• Scripter memory alignment (#9608)
• Zigbee battery percentage (#9607)
• HassAnyKey anomaly (#9601)
• ESP32 Webcam broken regression from #9590

[9.0.0.1] - 20201010

Added

• Optional support for Mitsubishi Electric HVAC by David Gwynne (#9237)
• Optional support for Orno WE517-Modbus energy meter by Maxime Vincent (#9353)
• SDM630 three phase ImportActive Energy display when #define SDM630_IMPORT is enabled by Janusz Kostorz (#9124)
• Optional support for inverted NeoPixelBus data line by enabling #define USE_WS2812_INVERTED (#8988)
• PWM dimmer color/trigger on tap, SO88 led, DGR WITH_LOCAL flag by Paul Diem (#9474)
• Support for stateful ACs using StateMode in tasmota-ir.bin by Arik Yavilevich (#9472)
• Zigbee command ZbData for better support of device specific data
• Support for analog buttons indexed within standard button range

Changed

• Redesigning ESP8266 GPIO internal representation in line with ESP32 changing Template layout too
• New IR Raw compact format (#9444)
• MAX31865 driver to support up to 6 thermocouples selected by MX31865 CS instead of SSPI CS (#9103)
• A4988 optional microstep pin selection
• Pulsetime to allow use for all relays with 8 interleaved so Pulsetime1 is valid for Relay1, Relay9, Relay17 etc. (#9279)
• Status command output for disabled status types
• IRremoteESP8266 library from v2.7.10 to v2.7.11
• NeoPixelBus library from v2.5.0.09 to v2.6.0

Fixed

• Template conversion when GPIO17 is 0
• Template using #define USER_TEMPLATE (#9506)
• Ledlink blink when no network connected regression from v8.3.1.4 (#9292)
• Exception 28 due to device group buffer overflow (#9459)
• Shutter timing problem due to buffer overflow in calibration matrix (#9458)
• Light wakeup exception 0 (divide by zero) when WakeupDuration is not initialised (#9466)
• ADC initialization sequence (#9473)
• Thermostat sensor status corruption regression from v8.5.0.1 (#9449)

Removed

• Support for direct upgrade from Tasmota versions before v7.0
• Auto config update for all Friendlynames and Switchtopic from Tasmota versions before v8.0

[8.5.1] - 20201002

• Release Hannah

[8.5.0.1] - 20200907

Added

• Command SetOption110 1 to disable Zigbee auto-config when pairing new devices
• Command SetOption111 1 to enable frequency output for buzzer GPIO (#8994)
• Command SetOption112 1 to enable friendly name in zigbee topic (use with SetOption89)
• #define USE_MQTT_AWS_IOT_LIGHT for password based AWS IoT authentication
• #define MQTT_LWT_OFFLINE and #define MQTT_LWT_ONLINE to user_config.h (#9395)
• New shutter modes (#9244)
• Zigbee auto-config when pairing
• Support for MLX90640 IR array temperature sensor by Christian Baars
• Support for VL53L1X time of flight sensor by Johann Obermeier

Changed

• Replace ArduinoJson with JSMN for JSON parsing
• WakeUp uses 256 steps instead of 100 (#9241)
• Major redesign of TuyaMcu adding shutter, light and multiple dimmer support by Federico Leoni (#9330)

Fixed

• Energy total counters (#9263, #9266)
• Crash in ZbRestore
• Reset BMP sensors when executing command SaveData and define USE_DEEPSLEEP enabled (#9300)
• status 0 message when using define USE_MQTT_TLS due to small log buffer (#9305)
• status 13 exception 9 when more than one shutter is configured
• status 13 json message
• Shelly 2.5 higher temperature regression from 8.2.0.1 (#7991)

[8.5.0] - 20200907

• Release Hannah

[8.4.0.3] - 20200823

Added

• Command PowerDelta1 to PowerDelta3 to trigger on up to three phases (#9134)
• Zigbee web ui widget for Lights
• SetOption109 1 to force gen1 Alexa mode, for Echo Dot 2nd gen devices only
• Zigbee web ui for power metering plugs
• Experimental support for ESP32 TTGO Watch and I2S Audio by Gerhard Mutz

Changed

• References from http://thehackbox.org/tasmota/ to http://ota.tasmota.com/tasmota/

[8.4.0.2] - 20200813

Added

• Command SetOption103 0/1 to set TLS mode when TLS is selected
• Command SetOption104 1 to disable all MQTT retained messages
• Command SetOption106 1 to create a virtual White ColorTemp for RGBW lights
• Command SetOption107 0/1 to select virtual White as (0) Warm or (1) Cold
• Command SetOption108 0/1 to enable Teleinfo telemetry into Tasmota Energy MQTT (0) or Teleinfo only (1) - Add better config corruption recovery (#9046)
• Virtual CT for 4 channels lights, emulating a 5th channel
• Support for DYP ME007 ultrasonic distance sensor by Janusz Kostorz (#9113)
• Zigbee web gui widget for Temp/Humidity/Pressure sensors
• Zigbee battery icon

Changed

• White blend mode moved to using SetOption 105 instead of RGBWWTable

Fixed

• Display power control (#9114)

Removed

• Support for direct upgrade from versions before 6.6.0.11 to versions after 8.4.0.1

[8.4.0.1] - 20200730

Added

• Zigbee better support for IKEA Motion Sensor
• ESP32 Analog input support for GPIO32 to GPIO39
• Zigbee options to ZbSend Config and ReadConfig
• Command Restart 2 to halt system. Needs hardware reset or power cycle to restart (#9046)
• Command SetOption102 0/1 to switch between Teleinfo French Metering mode, legacy 1200 bps (0) or Linky standard 9600 bps (1)

Changed

• Triple-mode TLS via configuration in a single firmware (TLS AWS IoT, Letsencrypt and No-TLS)
• Berry C mapping moved to a separate berry_mapping library

Fixed

• ESP32 PWM range

[8.4.0] - 20200730

• Release George

[8.3.1.7] - 20200716

Added

• Command DzSend<type> <index>,<value1(;value2)|state> to send values or state to Domoticz
• Command SetOption100 0/1 to remove Zigbee ZbReceived value from {"ZbReceived":{xxx:yyy}} JSON message
• Command SetOption101 0/1 to add the Zigbee source endpoint as suffix to attributes, ex Power3 instead of Power if sent from endpoint 3
• Command (S)SerialSend6 <comma separated values> (#8937)
• Support for Sonoff Zigbee Bridge as module 75 (#8583)

Changed

• Limited support of Arduino IDE as an increasing amount of features cannot be compiled with Arduino IDE
• All timer references from Arm to Enable in GUI, Timer command and JSON message
• Domoticz commands prefix from Domoticz to Dz
• Ping now reports the hostname instead of IP address (#8948)
• Zigbee randomizing of parameters at first run or after Reset

Removed

• Remove Arduino ESP8266 Core support for versions before 2.7.1

[8.3.1.6] - 20200617

Added

• Command Module2 to configure fallback module on fast reboot (#8464)
• Command SetOption97 0/1 to switch between Tuya serial speeds 9600 bps (0) or 115200 bps (1)
• Command SetOption98 0/1 to provide rotary rule triggers (1) instead of controlling light (0)
• Command SetOption99 0/1 to enable zero cross detection on PWM dimmer
• Support for Energy sensor (Denky) for French Smart Metering meter provided by global Energy Providers, need a adapter. See dedicated full blog about French teleinformation stuff
• Library to be used for decoding Teleinfo (French Metering Smart Meter)
• Support for single wire LMT01 temperature Sensor by justifiably (#8713)
• Compile time interlock parameters (#8759)
• Compile time user template (#8766)
• Rotary encoder support for light dimmer and optional color temperature if button1 still pressed (#8670)
• Support for switches/relays using an AC detection circuitry e.g. MOES MS-104B or BlitzWolf SS5 (#8606)
• Support for Schneider Electric iEM3000 series Modbus energy meter by Marius Bezuidenhout

Changed

• ESP32 USER GPIO template representation decreasing template message size
• Define USE_TASMOTA_SLAVE into USE_TASMOTA_CLIENT
• Commands SlaveSend and SlaveReset into ClientSend and ClientReset
• IRremoteESP8266 library updated to v2.7.8

Fixed

• Exception or watchdog on rule re-entry (#8757)

[8.3.1.5] - 20200616

Added

• ESP32 ethernet commands EthType 0/1, EthAddress 0..31 and EthClockMode 0..3
• Zigbee initial support for EmberZNet protocol (raw send/receive only)

[8.3.1.4] - 20200615

Added

• Basic support for ESP32 ethernet adding commands Wifi 0/1 and Ethernet 0/1 both default ON

[8.3.1.3] - 20200611

Added

• Initial support for Telegram bot (#8619)
• Support for HP303B Temperature and Pressure sensor by Robert Jaakke (#8638)
• Rule trigger System#Init to allow early rule execution without Wi-Fi and mqtt initialized yet
• Serial to TCP bridge, TCPStart and TCPBaudRate (needs #define USE_TCP_BRIDGE)

[8.3.1.2] - 20200522

Added

• Command Time 4 to display timestamp using milliseconds (#8537)
• Command SetOption94 0/1 to select MAX31855 or MAX6675 thermocouple support (#8616)
• Commands LedPwmOn 0..255, LedPwmOff 0..255 and LedPwmMode1 0/1 to control led brightness by George (#8491)
• Three Phase Export Active Energy to SDM630 driver
• Wildcard pattern ? for JSON matching in rules
• Support for unique MQTTClient (and inherited fallback topic) by full Mac address using mqttclient DVES_%12X (#8300)
• Zigbee options to ZbSend to write and report attributes
• CpuFrequency to status 2
• FlashFrequency to status 4
• Support for up to two BH1750 sensors controlled by commands BH1750Resolution and BH1750MTime (#8139)
• Zigbee auto-responder for common attributes
• Support for BL0940 energy monitor as used in Blitzwolf BW-SHP10 (#8175)

Changed

• Energy JSON Total field from "Total":[33.736,11.717,16.978] to "Total":33.736,"TotalTariff":[11.717,16.978]
• Energy JSON ExportActive field from "ExportActive":[33.736,11.717,16.978] to "ExportActive":33.736,"ExportTariff":[11.717,16.978]
• Adafruit_SGP30 library from v1.0.3 to v1.2.0 (#8519)

Fixed

• Escape of non-JSON received serial data (#8329)

[8.3.1.1] - 20200518

Added

• Command Rule0 to change global rule parameters
• More functionality to Switchmode 11 and 12 (#8450)
• Dump of compressed rules over 512 chars and unishox decompress fix
• Support for VEML6075 UVA/UVB/UVINDEX Sensor by device111 (#8432)
• Support for VEML7700 Ambient light intensity Sensor by device111 (#8432)

Changed

• IRremoteESP8266 library updated to v2.7.7

[8.3.1] - 20200518

• Release Fred

[8.3.0.2] - 20200517

Added

• Command DeviceName defaults to FriendlyName1 and replaces FriendlyName1 in GUI

Changed

• Hass discovery from using template name to new Device name (#8462)

[8.3.0.1] - 20200514

Changed

• KNX pow function to approximative pow saving 5k of code space
• Mutichannel Gas sensor pow function to approximative pow saving 5k of code space
• Quick Power Cycle detection from 4 to 7 power interrupts (#4066)

Fixed

• Fix default state of SetOption73 0 for button decoupling and send multi-press and hold MQTT messages

[8.3.0] - 20200514

• Release Fred

[8.2.0.6] - 20200501

Added

• Experimental basic support for Tasmota on ESP32 based on work by Jörg Schüler-Maroldt
• Support for analog anemometer by Matteo Albinola (#8283)
• Support for OpenTherm by Yuriy Sannikov (#8373)
• Support for Thermostat control by arijav (#8212)
• Automatic compression of Rules to achieve ~60% compression by Stephan Hadinger
• Command SetOption93 1 to control caching of compressed rules
• Rule trigger at root level like on loadavg<50 do power 2 endon after state command
• Zigbee support for router and end-device mode

Changed

• Flash access removing support for any Core before 2.6.3
• HAss discovery by Federico Leoni (#8370)
• Default PWM Frequency to 977 Hz from 223 Hz
• Minimum PWM Frequency from 100 Hz to 40 Hz
• PWM updated to the latest version of Arduino PR #7231
• Philips Hue emulation now exposes modelId and manufacturerId

[8.2.0.5] - 20200425

Changed

• Breaking Change Device Groups multicast address and port (#8270)
• IRremoteESP8266 library updated to v2.7.6

[8.2.0.4] - 20200417

Added

• Config version tag
• Command SetOption73 1 for button decoupling and send multi-press and hold MQTT messages by Federico Leoni (#8235)
• Command SetOption92 1 to set PWM Mode from regular PWM to ColorTemp control (Xiaomi Philips ...)
• Command SO as shortcut for command SetOption

Changed

• PWM implementation to Arduino #7231 removing support for Core versions before 2.6.3
• Default PWM Frequency to 223 Hz instead of 880 Hz for less interrupt pressure

Fixed

• Fix Zigbee DimmerUp/DimmerDown malformed

[8.2.0.3] - 20200329

Added

• Support for longer template names
• Zigbee command ZbBindState and manufattribute
• Zigbee command ZbConfig and configuration in Settings
• Commands CounterDebounceLow and CounterDebounceHigh to control debouncing (#8021)
• Commands NrfPage, NrfIgnore, NrfScan and NrfBeacon to NRF24 Bluetooth driver (#8075)
• Command SetOption90 1 to disable non-json MQTT messages (#8044)
• Command Sensor10 0/1/2 to control BH1750 resolution - 0 = High (default), 1 = High2, 2 = Low (#8016)
• Command Sensor10 31..254 to control BH1750 measurement time which defaults to 69 (#8016)
• Command Sensor18 0..32000 to control PMS5003 sensor interval to extend lifetime by Gene Ruebsamen (#8128)
• Command SetOption91 1 to enable fading at startup / power on
• Command SetOption41 <x> to force sending gratuitous ARP every seconds
• Command DevGroupName to specify up to four Device Group Names (#8087)
• Command DevGroupSend to send an update to a Device Group (#8093)
• Command Ping (#7176)
• Command Palette to add the ability to specify a palette of colors (#8150)
• Commands GlobalTemp and GlobalHum to init sensor data (#8152)
• Quick Wi-Fi reconnect using saved AP parameters when SetOption56 0 (#3189)
• More accuracy to GPS NTP server (#8088)
• Support for an iAQ sensor (#8107)
• Support for Seven Segment display using HT16K33 (#8116)
• Support for AS3935 Lightning Sensor by device111 (#8130)
• DimmerRange for PWM lights (#8120)

Changed

• Light scheme 2,3,4 cycle time speed from 24,48,72,... seconds to 4,6,12,24,36,48,... seconds (#8034)
• Remove floating point libs from IRAM
• Remove MQTT Info messages on restart for DeepSleep Wake (#8044)
• IRremoteESP8266 library updated to v2.7.5

Fixed

• PWM flickering during Wi-Fi connection (#8046)
• Zigbee crash with Occupancy sensor (#8089)
• Prevent multiple pings to run concurrently
• Scheme 2-4 brightness when SetOption68 1 (#8058)

[8.2.0.2] - 20200328

Added

• Support for up to four MQTT GroupTopics using the same optional Device Group names (#8014)
• Console command history (#7483, #8015)

[8.2.0.1] - 20200321

Added

• Zigbee command ZbRestore to restore device configuration dumped with ZbStatus 2
• Zigbee command ZbUnbind
• Support for unreachable (unplugged) Zigbee devices in Philips Hue emulation and Alexa
• Support for 64x48 SSD1306 OLED (#6740)

Changed

• HM-10 sensor type detection and add features (#7962)

Fixed

• Possible Relay toggle on (OTA) restart
• Zigbee sending wrong Sat value with Hue emulation

[8.2.0] - 20200321

• Release Elliot

[8.1.0.11] - 20200313

Added

• HAss Discovery support for Button and Switch triggers by Federico Leoni (#7901)
• Support for HDC1080 Temperature and Humidity sensor by Luis Teixeira (#7888)
• Commands SwitchMode 13 PushOn and SwitchMode 14 PushOnInverted (#7912)
• Command HumOffset -10.0 .. 10.0 to set global humidity sensor offset (#7934)
• Zigbee support for Hue emulation by Stephan Hadinger
• Dew Point to Temperature and Humidity sensors
• Support for ElectriQ iQ-wifiMOODL RGBW light by Ian King (#7947)

Changed

• Zigbee simplification of devices probing, saving Flash and memory

[8.1.0.10] - 20200227

Added

• Support for Jarolift rollers by Keeloq algorithm
• Zigbee features and improvements and remove support for Zigbee commands starting with Zigbee...
• Support for MaxBotix HRXL-MaxSonar ultrasonic range finders by Jon Little (#7814)
• Support for Romanian language translations by Augustin Marti
• Support for La Crosse TX23 Anemometer by Norbert Richter (#3146, #7765)
• Command SetOption89 0/1 for Zigbee distinct MQTT topics per device for SENSOR, allowing retained messages (#7835)

Changed

• Default my_user_config.h driver and sensor support removing most sensors and adding most drivers
• IRremoteESP8266 library updated to v2.7.4
• Revert switchmode 6 according to issue 7778 (#7831)
• Hue emulation code optimization

[8.1.0.9] - 20200220

Added

• Initial support for Sensors AHT10 and AHT15 by Martin Wagner (#7596)
• Support for Wemos Motor Shield V1 by Denis Sborets (#7764)
• Zigbee enhanced commands decoding, added ZbPing
• Commands SetOption85 0/1 and DevGroupShare supporting UDP Group command using GroupTopic without MQTT by Paul Diem (#7790)
• Support for Martin Jerry/acenx/Tessan/NTONPOWER SD0x PWM dimmer switches by Paul Diem (#7791)
• Command SetOption86 0/1 for PWM dimmer to turn brightness LED's off 5 seconds after last change
• Command SetOption87 0/1 for PWM dimmer to turn red LED on when powered off
• Command SetOption88 0/1 for PWM dimmer to let buttons control remote devices

Changed

• Revert most wifi connectivity changes introduced in 8.1.0.5 (#7746, #7602, #7621)

Fixed

• Zigbee auto-increment transaction number (#7757)

[8.1.0.8] - 20200212

Added

• Another new DHT driver based on ESPEasy. The old driver can still be used using define USE_DHT_OLD. The previous new driver can be used with define USE_DHT_V2 (#7717)

Changed

• MQTT message size with additional 200 characters
• Some wifi code to attempt faster connection (#7621)
• Display of some date and time messages from "Wed Feb 19 10:45:12 2020" to "2020-02-19T10:45:12"

Fixed

• Relation between RSSI and signal strength

[8.1.0.7] - 20200210

Added

• New DHT driver. The old driver can still be used using define USE_DHT_OLD (#7468)

Fixed

• wrong encoding of Zigbee persistent data

[8.1.0.6] - 20200205

Added

• Support for sensors DS18x20 and DHT family on Shelly 1 and Shelly 1PM using Shelly Add-On adapter (#7469)
• Commands SwitchMode 11 PushHoldMulti and SwitchMode 12 PushHoldMultiInverted (#7603)
• Command Buzzer -1 for infinite mode and command Buzzer -2 for following led mode (#7623)
• Support for MI-BLE sensors using HM-10 Bluetooth 4.0 module by Christian Staars (#7683)
• BootCount Reset Time as BCResetTime to Status 1
• ZbZNPReceivedand ZbZCLReceived being published to MQTT when SetOption66 1
• Optional Wifi AccessPoint passphrase define WIFI_AP_PASSPHRASE in my_user_config.h (#7690)
• Support for FiF LE-01MR energy meter by saper-2 (#7584)

Fixed

• HAss sensor discovery part 1/4 by Federico Leoni (#7582, #7548)
• MaxPower functionality (#7647)

[8.1.0.5] - 20200126

Added

• SetOption84 0/1 sends AWS IoT device shadow updates (alternative to retained)
• ZbBind (experimental) and bug fixes

Changed

• Wifi connectivity stability (#7602)
• IRremoteESP8266 library updated to v2.7.3

Fixed

• PWM flickering at low levels (#7415)

[8.1.0.4] - 20200116

Added

• Web page sliders when SetOption37 128 is active allowing control of white(s)
• Zigbee persistence and friendly names
• Most SetOptions as defines to my_user_config.h
• SoftwareSerial to CSE7766 driver allowing different GPIOs (#7563)
• Optional parameter <startcolor> to command Scheme <scheme>, <startcolor> to control initial start color
• Rule trigger on one level deeper using syntax with two # like on zigbeereceived#vibration_sensor#aqaracubeside=0 do ...

Changed

• Zigbee command prefix from Zigbee* to Zb*

Fixed

• PowerDelta zero power detection (#7515)
• OTA minimal gzipped detection regression from 8.1.0.3
• RGBWWTable ignored (#7572)

[8.1.0.3] - 20200106

Added

• Support for gzipped binaries
• SwitchMode 8 ToggleMulti, SwitchMode 9 FollowMulti and SwitchMode 10 FollowMultiInverted (#7522)

Changed

• Commands Prefix, Ssid, StateText, NTPServer, and FriendlyName displaying all items
• IRremoteESP8266 library updated to v2.7.2

Fixed

• WakeUp <x> ignores provided value (#7473)
• Exception 9 restart on log message in Ticker interrupt service routines NTP, Wemos and Hue emulation (#7496)

[8.1.0.2] - 20191230

Added

• Support for AdcParam parameters to control ADC0 Current Transformer Apparent Power formula by Jodi Dillon (#7100)
• Optional support for Prometheus using file xsns_91_prometheus.ino (#7216)
• Command ShutterButton <parameters> to control shutter(s) by to-scho (#7403)
• Command SetOption82 0/1 to limit the CT range for Alexa to 200..380
• Experimental support for NRF24L01 as BLE-bridge for Mijia Bluetooth sensors by Christian Baars (#7394)
• Support to BMP driver to enter reset state (sleep enable) when deep sleep is used in Tasmota

Fixed

• LCD line and column positioning (#7387)
• Display handling of hexadecimal escape characters (#7387)
• Improved fade linearity with gamma correction
• Wrong gamma correction for Module 48 lights (PWM5 for CT)

[8.1.0.1] - 20191225

Added

• Command SetOption79 0/1 to enable reset of counters at teleperiod time by Andre Thomas (#7355)
• SerialConfig to Status 1
• WifiPower to Status 5
• Support for DS1624, DS1621 Temperature sensor by Leonid Myravjev
• Zigbee attribute decoder for Xiaomi Aqara Cube

Changed

• Lights: simplified gamma correction and 10 bits internal computation

Fixed

• Sonoff Bridge, Sc, L1, iFan03 and CSE7766 serial interface to forced speed, config and disable logging
• Serial initialization regression from previous fix
• Commands Display and Counter from overruling command processing (#7322)
• White added to light status (#7142)

[8.1.0] - 20191225

• Release Doris

[8.0.0.3] - 20191224

Changed

• Version bump due to internal Settings change

[8.0.0.2] - 20191223

Added

• Zigbee better support for Xiaomi Double Switch and Xiaomi Vibration sensor
• Support for AdcParam parameters to control ADC0 Moisture formula by Federico Leoni (#7309)
• Commands WebButton1 until WebButton16 to support user defined GUI button text (#7166)

Changed

• Settings variable namings
• Number of FriendlyNames from 4 to 8

[8.0.0.1] - 20191221

Added

• Support for max 150 characters in most command parameter strings (#3686, #4754)
• Support for GPS as NTP server by Christian Baars and Adrian Scillato
• Zigbee coalesce sensor attributes into a single message
• Deepsleep start delay based on Teleperiod if Teleperiod differs from 10 or 300

Changed

• Settings text handling allowing variable length text within a total text pool of 699 characters
• Smoother Fade using 100Hz instead of 20Hz animation (#7179)
• Number of rule Vars and Mems from 5 to 16 (#4933)

[7.2.0] - 20191221

• Release Constance

Changed

• Basic version string to lite (#7291)

Fixed

• Arduino IDE compile error (#7277)
• Restore ShutterAccuracy, MqttLog, WifiConfig, WifiPower and SerialConfig (#7281)
• No AP on initial install (#7282)
• Failing downgrade (#7285)

7.1.2.6 20191214

• Change some more Settings locations freeing up space for future single char allowing variable length text
• Change tasmota-basic.bin and FIRMWARE_BASIC to tasmota-lite.bin and FIRMWARE_LITE
• Fix DeepSleep in case there is no wifi by Stefan Bode (#7213)
• Fix Fade would ignore savedata 0 and store to flash anyways (#7262)
• Add Zigbee send automatic ZigbeeRead after sending a command
• Add Zigbee improving Occupancy:false detection for Aqara sensor
• Add fallback support from version 8.x
• Add restriction if fallback firmware is incompatible with settings resulting in unreachable device
• Add support for DHT12 Temperature and Humidity sensor by Stefan Oskamp

7.1.2.5 20191213

• Change some Settings locations freeing up space for future single char allowing variable length text
• Add Zigbee support for Xiaomi Aqara Vibration Sensor and Presence Sensor by Stephan Hadinger
• Add Shutter functions ramp up/down and MQTT reporting by Stefan Bode

7.1.2.4 20191209

• Change HTTP CORS from command SetOption73 0/1 to Cors <cors_domain> allowing user control of specific CORS domain by Shantur Rathore (#7066)
• Change GUI Shutter button text to Up and Down Arrows based on PR by Xavier Muller (#7166)
• Change amount of supported DHT sensors from 3 to 4 by Xavier Muller (#7167)
• Revert removal of exception details from MQTT info on restart
• Add Wifi Signal Strength in dBm in addition to RSSI Wifi Experience by Andreas Schultz (#7145)
• Add Yaw, Pitch and Roll support for MPU6050 by Philip Barclay (#7058)
• Add reporting of raw weight to JSON from HX711 to overcome auto-tare functionality by @tobox (#7171)
• Add command Sensor34 9 <weight code> to set minimum delta to trigger JSON message by @tobox (#7188)
• Fix flashing H801 led at boot by Stephan Hadinger (#7165, #649)
• Fix duplicated Backlog when using Event inside a Backlog by Adrian Scillato (#7178, #7147)
• Fix Gui Timer when using a negative zero offset of -00:00 by Peter Ooms (#7174)

7.1.2.3 20191208

• Change Exception reporting removing exception details from both MQTT info and Status 1. Now consolidated in Status 12 if available.

7.1.2.2 20191206

• Remove rule trigger tele_power1#state due to compatibility
• Add command SerialConfig 0..23 or SerialConfig 8N1 to select Serial Config based in PR by Luis Teixeira (#7108)
• Add save call stack in RTC memory in case of crash, command Status 12 to dump the stack by Stephan Hadinger
• Add Home Assistant force update by Frederico Leoni (#7140, #7074)

7.1.2.1 20191206

• Add SML bus decoder syntax support for byte order by Gerhard Mutz (#7112)
• Add rule var %topic% by Adrian Scillato (#5522)
• Add rule triggers tele_power1#state and multiple tele-wifi1#xxx by Adrian Scillato (#7093)
• Add experimental support for stepper motor shutter control by Stefan Bode
• Add optional USE_MQTT_TLS to tasmota-minimal.bin by Bohdan Kmit (#7115)

7.1.2 20191206

• Maintenance Release

7.1.1.1 20191201

• Fix lost functionality of GPIO9 and GPIO10 on some devices (#7080)
• Fix Zigbee uses Hardware Serial if GPIO 1/3 or GPIO 13/15 and SerialLog 0 (#7071)
• Fix WS2812 power control (#7090)
• Change light color schemes 2, 3 and 4 from color wheel to Hue driven with user Saturation control
• Change log buffer size from 520 to 700 characters accommodating full rule text (#7110)

7.1.1 20191201

• Maintenance Release

7.1.0.1 20191130

• Fix slider for devices with one or two channels like only white or white/yellow
• Fix TasmotaSlave buffer overrun on Tele
• Fix light scheme 4 speed (#7072)
• Add support for TasmotaSlave executing commands on Tasmota

7.1.0 20191129

• Release Doris

7.0.0.6 20191122

• Add colorpicker to WebUI by Christian Staars (#6984)
• Change new Fade system much smoother, Speed now up to 40 (#6942, #3714)
• Fix Arduino IDE function prototyping compile error (#6982)
• Change update lib IRremoteESP8266 updated to v2.7.1, -2.7k flash and -1.5k RAM for Tasmota-IR
• Fix auto--power on/off when setting channel to non-zero or zero value, when SetOption68 1
• Fix postpone saving settings to flash until Fade is complete, avoids pause in Fade
• Add command SetOption77 0/1 to keep power on when slider is far left

7.0.0.5 20191118

• Fix boot loop regression
• Add command TempOffset -12.6 .. 12.6 to set global temperature sensor offset (#6958)
• Fix check deepsleep for valid values in Settings (#6961)
• Fix Wifi instability when light is on, due to sleep=0 (#6961, #6608)
• Add hardware detection to be overruled with SetOption51 (#6969)

7.0.0.4 20191108

• Add command WifiPower 0 .. 20.5 to set Wifi Output Power which will be default set to 17dBm
• Change supported PCF8574 I2C address range to 0x20 - 0x26 allowing other I2C devices with address 0x27 to be used at the same time
• Change supported PCF8574A I2C address range to 0x39 - 0x3F allowing other I2C devices with address 0x38 to be used at the same time
• Change supported MCP230xx I2C address range to 0x20 - 0x26 allowing other I2C devices with address 0x27 to be used at the same time
• Add Keep last channels values when Color command end with '=' (#6799)
• Add support for I2C sensor TLS2591 Light Intensity sensor (#6873)
• Change Kept only NEC/RC5/RC6/HASH IR protocols in standard Tasmota, all other protocols require Tasmota-IR, saving 4K
• Add command SetOption76 0/1 to enable incrementing bootcount when deepsleep is enabled (#6930)
• Change Reset erase end address from as seen by SDK (getFlashChipSize) to full flash size (getFlashChipRealSize)
• Change Zigbee log verbosity reduction

7.0.0.3 20191103

• Add command I2cDriver for I2C driver runtime control using document I2CDEVICES.md
• Fix random crash caused by UPNP flood
• Add support for Honeywell HPMA115S0 particle concentration sensor by David Hunt (#6843)
• Remove driver xsns_12_ads1115_i2cdev replaced by xsns_12_ads1115

7.0.0.2 20191102

• Add command WebColor19 to control color of Module and Name (#6811)
• Add support for Honeywell I2C HIH series Humidity and Temperetaure sensor (#6808)
• Fix wrong Dimmer behavior introduced with #6799 when SetOption37 < 128
• Change add DS18x20 support in Tasmota-IR
• Add Zigbee command support, considered as v1.0 for full Zigbee support
• Fix Reduce flash size after change to IRremoteESP8266 v2.7.0

7.0.0.1 20191027

• Remove update support for versions before 6.0
• Change default GUI to dark theme
• Add command SetOption73 0/1 to re-enable HTTP Cross-Origin Resource Sharing (CORS) now default disabled (#6767)
• Add frequency to ADE7953 energy monitor as used in Shelly 2.5 by ljakob (#6778)
• Add command SetOption74 0/1 to enable DS18x20 internal pull-up and remove define DS18B20_INTERNAL_PULLUP (#6795)
• Fix better control of RGB/White when SetOption37 >128, added Dimmer1 and Dimmer2 commands (#6714)
• Add hide Alexa objects with friendlyname starting with '$' (#6722, #6762)
• Add command SetOption75 0/1 to switch between grouptopic (0) using fulltopic replacing %topic% or (1) is cmnd/<grouptopic> (#6779)
• Change IRremoteESP8266 library to v2.7.0

6.7.1.1 20191026

• Change ArduinoSlave to TasmotaSlave
• Add support for Tuya battery powered devices (#6735)
• Change repository name from Sonoff-Tasmota to Tasmota and all code references from Sonoff to Tasmota

6.7.1 20191026

• Release Allison
• Fix on energy monitoring devices using PowerDelta Exception0 with epc1:0x4000dce5 = Divide by zero (#6750)
• Fix Script array bug (#6751)

6.7.0 20191025

• Release

6.6.0.21 20191022

• Remove support for WPS and SmartConfig in favour of Web server (!) based WifiManager (#6680)
• Remove binary sonoff-classic (#6680)
• Remove command SetOption2

6.6.0.20 20191018

• Add command SetOption65 0/1 to disable (1) fast power cycle detection fixing unwanted brownout trigger
• Add absolute PowerDelta using command PowerDelta 101..32000 where 101 = 101-100 = 1W, 202 = 202-100 = 102W (#5901)
• Add support for EX-Store WiFi Dimmer V4 (#5856)
• Add ZigbeeRead command and many improvements (#6095)
• Add ArduinoSlave driver (EXPERIMENTAL)

6.6.0.19 20191018

• Replace obsolete xsns_23_sdm120 with xnrg_08_sdm120 and consolidate define USE_SDM120
• Replace obsolete xsns_25_sdm630 with xnrg_10_sdm630 and consolidate define USE_SDM630
• Replace obsolete xsns_49_solaxX1 with xnrg_12_solaxX1 (#6677)

6.6.0.18 20191010

• Add command DimmerRange in Light module to support 2 byte dimming ranges from Tuya
• Add Zigbee additional commands and sending messages to control devices (#6095)
• Fix Rules were not triggered with IR unknown protocol or in sonoff-it (#6629)
• Add define USE_DEEPSLEEP and command DeepSleepTime 0 or 10..86400 (seconds) to enter deepsleep mode (#6638)
• Add define USE_SONOFF_RF to enable/disable Sonoff Rf support (#6648)
• Add incremental beeps to Ifan03 remote control fan speed buttons (#6636)
• Add rule support after every command execution like Fanspeed#Data=2 (#6636)
• Fix handling of ligth channels when pwm_multichannel (Option68) is enabled
• Add WebUI for multiple, independent PWM channels
• Remove default DS18B20 driver and only support define DS18x20 (#6647)
• Add support for PMS3003 dust particle sensor
• Change Sonoff L1 support by adding define USE_SONOFF_L1

6.6.0.17 20191009

• Add command SetOption34 0..255 to set backlog delay. Default value is 200 (mSeconds) (#6562)
• Add command Gpio 255 to show physical GPIO configuration of all non-flash pins (#6407)

6.6.0.16 20191008

• Change PZEM004T default address mask from 0.0.0.x to 192.168.1.x for legacy reason (#6585)
• Fix PZEM004T, PZEMAC and PZEMDC autodetection (#6585)
• Change light drivers internals to ease management

6.6.0.15 20191003

• Change command PulseTime JSON message format and allow display of all pulsetimer information (#6519)
• Add support for Chint DDSU666 Modbus energy meter by Pablo Zerón
• Add support for SM2135 as used in Action LSC Smart Led E14 (#6495)
• Add command SetOption72 0/1 to switch between software (0) or hardware (1) energy total counter (#6561)
• Add Zigbee tracking of connected devices and auto-probing of Manuf/Model Ids
• Fix better handling of PWM White Temperature mode for Module 48 (#6534)

6.6.0.14 20190925

• Change command Tariffx to allow time entries like 23 (hours), 1320 (minutes) or 23:00. NOTE: As this is development branch previous tariffs are lost! (#6488)
• Remove support for define USE_DS18x20_LEGACY and legacy DS18x20 driver (#6486)
• Add initial support for MQTT logging using command MqttLog <loglevel> (#6498)
• Add Zigbee more support - collect endpoints and clusters, added ZigbeeDump command
• Add initial support for shutters by Stefan Bode (#288)
• Add command to MCP230xx: sensor29 pin,0/1/2 for OFF/ON/TOGGLE
• Add initial support for PCF8574 I2C I/O Expander (currently output only) by Stefan Bode
• Add command SetOption71 0/1 to switch between different Modbus Active Energy registers on DDS238-2 energy meters (#6531)
• Change command SetOption43 to make it more general. Now supports PS_16_DZ driver too (#6544)
• Change command handling by moving buffers up in chain solving MQTTlog support (#6529)
• Change detection of non-MQTT commands by allowing non-space characters as delimiter (#6540)
• Fix TasmotaSerial: move serial send to IRAM for high speed baud rates

6.6.0.13 20190922

• Add command EnergyReset4 x,x to initialize total usage for two tarrifs
• Add command EnergyReset5 x,x to initialize total export (or production) for two tarrifs
• Add command Sensor34 8,0 and Sensor34 8,1 to disable/enable JSON message on weight change over 4 gram
• Add JSON array index support to rules evaluation allowing trigger on ENERGY#POWER[2]>0.60 from JSON ..,"Power":[0.00,0.68],.. (#6160)

6.6.0.12 20190910

• Redesign command Tariff to now default to 0 (=disabled) and allowing to set both Standard Time (ST) and Daylight Savings Time (DST) start hour
• Commands Tariff1 22,23 = Tariff1 (Off-Peak) ST,DST Tariff2 (Standard) 6,7 = Tariff2 ST,DST Tariff9 0/1 = Weekend toggle (1 = Off-Peak during weekend)
• Change rename "Data" to "Hash" and limit to 32 bits when receiving UNKNOWN IR protocol (see DECODE_HASH from IRremoteESP8266)
• Add command Gpios 255/All to show all available GPIO components (#6407)
• Change JSON output format for commands Adc, Adcs, Modules, Gpio and Gpios from list to dictionary (#6407)
• Add Zigbee support phase 3 - support for Xiaomi lumi.weather air quality sensor, Osram mini-switch
• Change energy sensors for three phase/channel support
• Add support for Shelly 2.5 dual energy (#6160)
• Add initial support for up to three PZEM-014/-016 on serial modbus connection with addresses 1 (default), 2 and 3 (#2315)
• Add initial support for up to three PZEM-004T on serial connection with addresses x.x.x.1 (default), 2 and 3 (#2315)
• Add initial support for up to three PZEM-003/-017 on serial modbus connection with addresses 1 (default), 2 and 3 (#2315)
• Add driver USE_SDM630_2 as future replacement for USE_SDM630 - Pls test and report
• Add command ModuleAddress 1/2/3 to set Pzem module address when a single module is connected (#2315)

6.6.0.11 20190907

• Change Settings crc calculation allowing short term backward compatibility
• Add support for up to 4 INA226 Voltage and Current sensors by Steve Rogers (#6342)
• Change Improve reliability of TasmotaSerial at 115200 bauds and reduce IRAM usage for Stage/pre-2.6
• Add support for A4988 stepper-motor-driver-circuit by Tim Leuschner (#6370)
• Add support for Hiking DDS238-2 Modbus energy meter by Matteo Campanella (#6384)

6.6.0.10 20190905

• Redesign Tuya support by Shantur Rathore removing commands SetOption34, 41, 44, 45, 46 and 65 (#6353)
• Add command Reset 99 to reset bootcount to zero (#684, #6351)
• Change command Time 1/2/3 to select JSON time format ISO, ISO + Epoch or Epoch for legacy reason

6.6.0.9 20190828

• Change theoretical baudrate range to 300..19660500 bps in 300 increments (#6294)
• Add Full support of all protocols in IRremoteESP8266, to be used on dedicated-IR Tasmota version. Warning: +81k Flash when compiling with USE_IR_REMOTE_FULL
• Add compile time define USE_WS2812_HARDWARE to select hardware type WS2812, WS2812X, WS2813, SK6812, LC8812 or APA106 (DMA mode only)
• Add 'sonoff-ir' pre-packaged IR-dedicated firmware and 'sonoff-ircustom' to customize firmware with IR Full protocol support
• Add Zigbee support phase 2 - cc2530 initialization and basic ZCL decoding
• Add driver USE_SDM120_2 with Domoticz P1 Smart Meter functionality as future replacement for USE_SDM120 - Pls test and report
• Add command Power0 0/1/2/Off/On/Toggle to control all power outputs at once (#6340)
• Add time to more events (#6337)
• Add command Time 1/2/3 to select JSON time format ISO + Epoch, ISO or Epoch

6.6.0.8 20190827

• Add Tuya Energy monitoring by Shantur Rathore
• Add phase 1 Domoticz P1 Smart Meter support using energy sensors handled by xdrv_03_energy.ino based on an idea by pablozg
• Add commands Tariff1 0..23 (start Off-Peak hour), Tariff2 0..23 (start Standard hour) and Tariff3 0/1 (Saturday and Sunday Off-Peak)

6.6.0.7 20190825

• Expand Settings area to 4k for future use

6.6.0.6 20190819

• Add I2C display driver for SH1106 oled by Gerhard Mutz
• Add SPI display drivers for epaper 4.2 inch, ILI9488 TFT, SSD1351 Color oled and RA8876 TFT by Gerhard Mutz
• Add support for HM17 bluetooth LE passive scan of ibeacon devices by Gerhard Mutz

6.6.0.5 20190816

• Add command WebSensor 0/1 to control display of sensor data in web GUI (#6085)
• Change some table locations from RAM to Flash
• Fix wrong telemetry message when SetOption68 1 (#6191)
• Add support for RDM6300 125kHz RFID Reader by Gerhard Mutz

6.6.0.4 20190806

• Add support for CHIRP soil moisture sensor by Christian Baars
• Add debug compile features using defines DEBUG_TASMOTA_CORE, DEBUG_TASMOTA_DRIVER and DEBUG_TASMOTA_SENSOR.
• See DEBUG_CORE_LOG example in sonoff.ino and DEBUG_DRIVER_LOG example in xdrv_09_timers.ino
• Add support for Solax X1 inverter by Pablo Zerón
• Add ZigBee support phase 1 - low level MQTT ZNP messages for CC2530 devices
• Add command Buzzer with optional parameters ,<duration of beep in 100mS steps>,<duration of silence in 100mS steps> enabled when a buzzer is configured (#5988)
• Add support for PAJ7620 gesture sensor by Christian Baars

6.6.0.3 20190725

• Change filename of configuration backup from using FriendlyName1 to Hostname solving diacritic issues (#2422)
• Change Store AWS IoT Private Key and Certificate in SPI Flash avoiding device-specific compilations
• Upgrade library IRRemoteEsp8266 to 2.6.4, now using sendPioneer()
• Add support for MAX31865 Thermocouple sensor by Alberto Lopez Siemens
• Add option 0 to Width1 (Marker), Width2 (Second), Width3 (Minute) and Width4 (Hour) disabling display (#6152)
• Add MqttCount metric to STATE (#6155)
• Add define USE_ENERGY_MARGIN_DETECTION to disable Energy Margin and Power Limit detection
• Add define USE_ENERGY_POWER_LIMIT to disable Energy Power Limit detection while Energy Margin detection is active
• Add allow repeat/longpress for IRSend raw, introduced IRSend option (#6074)
• Add SetOption68 to enable multi-channel PWM instead of a single light (#6134)

6.6.0.2 20190714

• Change commands Var and Mem to show all parameters when no index is given (#6107)
• Add command SetOption67 0/1 to disable or enable a buzzer as used in iFan03
• Add command DisplayWidth to set pixel width on supported devices
• Add command DisplayHeight to set pixel height on supported devices
• Add support for Sonoff iFan03 as module 71 (#5988)
• Add support for a buzzer
• Add support for IRSend long press ('repeat' feature from IRRemoteESP8266) (#6074)
• Add support for IRHVAC Midea/Komeco protocol (#3227)
• Add support for more IRSend protocols enabled in my_user_config.h
• Add support for IRSend Pioneer protocol (#6100)
• Add Oled reset GPIO option "OLED reset"

6.6.0.1 20190708

• Fix Domoticz battery level set to 100 if define USE_ADC_VCC is not used (#6033)
• Fix Force Elliptic Curve for Letsencrypt TLS #6042
• Fix WeMo emulation for 1G echo and 2G echo dot (#6086)
• Fix Xiaomi Philips brightness (#6091)
• Change defines USE_TX20_WIND_SENSOR and USE_RC_SWITCH in my_user_config.h to disable to lower iram usage enabling latest core compilation (#6060, #6062)
• Add blend RGB leds with White leds for better whites (#5895, #5704)
• Add command SetOption41 0..8 to control number of Tuya switches (#6039)
• Add command SetOption42 0..255 to set overtemperature (Celsius only) threshold resulting in power off all on energy monitoring devices. Default setting is 90 (#6036)
• Add command SetOption66 0/1 to enable or disable Tuya dimmer range 255 slider control
• Add command Time to disable NTP and set UTC time as Epoch value if above 1451602800 (=20160101). Time 0 re-enables NTP (#5279)
• Add AZ7798 automatic setting of clock display (#6034)
• Add Epoch and UptimeSec to JSON messages (#6068)
• Add support for up to 4 INA219 sensors (#6046)

6.6.0 20190707

• Remove support of TLS on core 2.3.0 and extent support on core 2.4.2 and up
• Remove MQTT uptime message every hour
• Refactor some defines to const
• Refactor webserver HTML input, button, textarea, and select name based on id
• Refactor webserver sensor data collection
• Refactor TLS based on BearSSL, warning breaking change for fingerprints validation
• Refactor management of lights, using classes and integers instead of floats
• Refactor UDP initial message handling from string to char using static memory and add debug info (#5505)
• Refactor IRSend and receive for 64-bit support (#5523)
• Refactor MQTT which might solve issue (#5755)
• Refactor IRSend by using heap when more than 199 values need to be send. May need increase of define MQTT_MAX_PACKET_SIZE too (#5950)
• Refactor double to float in rules, and replaced trigonometric functions from stdlib with smaller versions (#6005)
• Change pubsubclient MQTT_KEEPALIVE from 10 to 30 seconds for AWS IoT support
• Change gamma correction as default behavior, ie "Ledtable 1"
• Change PWM resolution from 8 to 10 bits for low brightness lights
• Change IRSend Panasonic protocol to 64-bit (#5523)
• Change ADC0 to enabled by default in my_user_config.h (#5671)
• Change define USE_EMULATION by USE_EMULATION_HUE and USE_EMULATION_WEMO (#5826)
• Change default PowerDelta from 80% to 0% on new installations (#5858, #5028, #4813, #4130, #4145, #3795, #3778, #3660, #3648)
• Fix display Bug in KNX webmenu for Physical Address
• Fix the Unescape() function and the SendSerial3 behaviour
• Fix webserver multiple Javascript window.onload functionality
• Fix TasmotaSerial at 9600 bps solving DFPlayer comms (#5528)
• Fix Configure Timer Web GUI (#5568)
• Fix Shelly 2.5 I2C address priority issue when VEML6070 code is present by disabling VEML6070 for Shelly 2.5 (#5592)
• Fix use of SerialDelimiter value 128 (#5634)
• Fix Sonoff Pow R2 / S31 invalid energy increments (#5789)
• Fix core 2.5.x ISR not in IRAM exception (#5837)
• Fix Philips Hue emulation Alexa issue by using part of MAC address for LightId (#5849)
• Fix missing white channel for WS2812 (#5869)
• Fix PZem startup issue (#5875)
• Fix exception 9 when syslog is enabled and NTP is just synced (#5917)
• Fix Toggle functionality to button double press when one button and two devices are detected (#5935)
• Fix channel command for dual dimmers (#5940)
• Fix not restoring white value on power off/power on (#5993)
• Add command AdcParam to control ADC0 Temperature and Light formula parameters
• Add command LedMask to assign which relay has access to power LED (#5602, #5612)
• Add extended LED power control using command LedPowerX where X is 1 to 4. Enabled when "LedLink(i)" is configured too (#5709)
• Add command Sensor20 1..255 to change Nova Fitness SDS01 working period in minutes (#5452)
• Add command SetOption38 6..255 to set IRReceive protocol detection sensitivity mimizing UNKNOWN protocols (#5853)
• Add command SetOption39 1..255 to control CSE7766 (Pow R2) or HLW8032 (Blitzwolf SHP5) handling of power loads below 6W. Default setting is 128 (#5756)
• Add command SetOption40 0..250 to disable button functionality if activated for over 0.1 second. Needs SetOption1 1 and SetOption13 0 (#5449)
• Add command SetOption63 0/1 to disable relay state feedback scan at restart (#5594, #5663)
• Add command SetOption64 0/1 to switch between "-" or "_" as sensor index separator impacting DS18X20, DHT, BMP and SHT3X sensor names (#5689)
• Add command SetOption65 0/1 and more Tuya Serial based device support (#5815)
• Add command WebColor to change GUI colors on the fly
• Add support for AWS IoT with TLS 1.2 on core 2.4.2 and up. Full doc here: https://github.com/arendst/Tasmota/wiki/AWS-IoT
• Add support for Badger HR-E Water Meter (#5539)
• Add support for Shelly 2.5 Energy and overtemp Monitoring (#5592)
• Add support for color and colortone for Philips Hue emulation via Alexa (#5600 #4809)
• Add support for Scripts as replacement for Rules. Default disabled but can be enabled in my_user_config.h (#5689)
• Add support for up to four LEDs related to four power outputs. Enabled when "LedLink(i)" is configured too (#5709)
• Add support for Shelly 1PM Template {"NAME":"Shelly 1PM","GPIO":[56,0,0,0,82,134,0,0,0,0,0,21,0],"FLAG":2,"BASE":18} (#5716)
• Add support for SPS30 Particle sensor thanks to Gerhard Mutz (#5830)
• Add support for VL53L0x time of flight sensor. Might interfere with TSL2561 using same I2C address (#5845)
• Add support for Sonoff L1 thanks to reef-actor (#6002)
• Add rule Http#Initialized
• Add rule System#Save executed just before a planned restart
• Add rule support for single JSON value pair like {"SSerialReceived":"on"} by expanding it to {"SSerialReceived":{"Data":"on"}} allowing for trigger SSerialReceived#Data=on (#5638)
• Add define USE_COUNTER to my_user_config.h to save space in sonoff-basic.bin and sonoff-minimal.bin
• Add define USE_DHT to my_user_config.h to save space in sonoff-basic.bin
• Add defines USE_EMULATION_WEMO and USE_EMULATION_HUE to my_user_config.h to control emulation features at compile time (#5826)
• Add Toggle functionality to button double press when more devices are detected
• Add device OverTemp (>73 Celsius) detection to Energy Monitoring devices with temperature sensor powering off all outputs
• Add Tuya Dimmer 10 second heartbeat serial packet required by some Tuya dimmer secondary MCUs
• Add all temperature, humidity and pressure for global access
• Add validation check when loading settings from flash
• Add HX711 weight restore after controlled restart or after power restore just before executing command Sensor34 7 (#5367, #5786)
• Add GUI hexadecimal color options in my_user_config.h (#5586)
• Add alternative IRSend command syntax IRSend raw,<freq>,<header mark>,<header space>,<bit mark>,<zero space>,<one space>,<bit stream> (#5610)
• Add user configurable ADC0 to Module and Template configuration compatible with current FLAG options (#5671)
• Add AriLux RF control GPIO option "ALux IrSel" (159) replacing "Led4i" (59) for full LED control (#5709)
• Add LED GPIO option "LedLink" (157) and "LedLinki" (158) to select dedicated link status LED (#5709)
• Add all 5 PWM channels individually addressable with LEDs. (#5741)
• Add reset of Energy values when connection to sensor is lost for over 4 seconds (#5874, #5881)
• Add checkbox to GUI password field enabling visibility during password entry only (#5934)

6.5.0 20190319

• Remove commands SetOption14 and SetOption63 as it has been superseded by command Interlock
• Remove command SetOption35 0-255 for mDNS start-up delay (#4793)
• Remove support for MQTT_LIBRARY_TYPE, MQTT_ARDUINOMQTT and MQTT_TASMOTAMQTT (#5474)
• Change webserver content handling from single String to small Chunks increasing RAM
• Change code use of boolean to bool and byte to uint8_t
• Change code uint8_t flags to bool flags
• Change sonoff_template.h layout regarding optional module flags like ADC0
• Change sonoff_template.h module lay-out by removing non-configurable GPIOs
• Change button driver making it modular
• Change switch driver making it modular and introduce input filter (#4665, #4724)
• Change switch input detection by optimizing switch debounce (#4724)
• Change web authentication (#4865)
• Change image name BE_MINIMAL to FIRMWARE_MINIMAL and USE_xyz to FIRMWARE_xyz (#5106)
• Change GUI weblog from XML to plain text solving possible empty screens (#5154)
• Fix most compiler warnings
• Fix Display exception 28 when JSON value is nullptr received
• Fix epaper driver (#4785)
• Fix HAss Sensor Discovery Software Watchdog restart (#4831, #4988)
• Fix allowable MAX_RULE_VARS to 16 (#4933)
• Fix mDNS addService (#4938, #4951)
• Fix HAss discovery of MHZ19(B) sensors (#4992)
• Fix some exceptions and watchdogs due to lack of stack space (#5215)
• Fix GUI wifi password acception starting with asterisks (*) (#5231, #5242)
• Fix command WebSend intermittent results (#5273, #5304)
• Fix additional characters in fallbacktopic, hostname and mqttclient on core 2.5.0 (#5359, #5417)
• Fix Energy TotalStartTime when commands EnergyReset0 and/or EnergyReset3 used (#5373)
• Fix DS18S20 temperature calculation (#5375)
• Fix float calculations in range from 0 to -1 (#5386)
• Fix exception on GUI Configure Logging and Configure Other (#5424)
• Add commands PowerCal, VoltageCal and CurrentCal for HLW8012, HJL01 and BL0937 based energy sensors
• Add command SerialDelimiter 128 to filter reception of only characters between ASCII 32 and 127 (#5131)
• Add command SSerialSend5 <hexdata> to SerialBridge
• Add command Interlock 0 / 1 / 1,2 3,4 .. to control interlock ON/OFF and add up to 8 relays in 1 to 4 interlock groups (#4910, #5014)
• Add command Template 255 to copy module configuration over to current active template and store as user template named Merged (#5371)
• Add command WifiConfig 7 to allow reset of device in AP mode without admin password (#5297)
• Add command SetOption36 to control boot loop default restoration (#4645, #5063)
• Add command SetOption37 for RGBCW color mapping (#5326)
• Add command SetOption55 0/1 and define MDNS_ENABLE to disable/enable mDNS (#4793, #4923)
• Add command SetOption62 0/1 to disable retain on Button or Switch hold messages (#5299)
• Add support for Smanergy KA10 Smart Wall Socket with Energy monitoring
• Add support for commands in sensor drivers
• Add support for MAX31855 K-Type thermocouple sensor using softSPI (#4764)
• Add support for Near Field Communication (NFC) controller PN532 using Serial (#4791, #5162)
• Add support for OBI Power Socket 2 (#4829)
• Add support for YTF IR Bridge (#4855)
• Add support for Mi LED Desk Lamp with rotary switch (#4887)
• Add support for Digoo DG-SP202 Smart Socket with Energy monitoring (#4891)
• Add support for MAX44009 Ambient Light sensor (#4907)
• Add support for inverted buttons and inverted buttons without pullup (#4914)
• Add support for Luminea ZX2820 Smart Socket with Energy monitoring (#4921)
• Add support for multiple ADS1115 I2C devices (#5083)
• Add support for online template change using command Template or GUI Configure Other (#5177)
• Add support for Korean language translations (#5344)
• Add support for sensor SCD30 (#5434)
• Add parameter CFG_HOLDER to status 1 message (#5206)
• Add SetOption32 until SetOption49 diagnostic information to Status 3 report as replacement for second property value in SetOption property name
• Add Resolution property to Status 3 report providing previous SetOption second value property
• Add property MqttCount to status 6 message representing number of Mqtt re-connections
• Add property LinkCount to state and status 11 message representing number of Wifi Link re-connections
• Add property Downtime to state and status 11 message representing the duration of wifi connection loss
• Add variable %timestamp% to rules (#4749)
• Add rule support for "==", "!=" ">=" and "<=" (#5122)
• Add rule expression enabled by define USE_EXPRESSION in my_user_config.h (#5210)
• Add Power status functionality to LED2 when configured leaving LED1 for Link status indication
• Add user configuration of HLW8012 and HJL-01/BL0937 Energy Monitoring as used in Sonoff Pow and many Tuya based devices
• Add user configuration of MCP39F501 Energy Monitoring as used in Shelly2
• Add online template configuration using both commands and Configure Template menu option in GUI
• Add (S)SerialSend3 escape sequence \x to allow hexadecimal byte value (#3560, #4947)
• Add define DS18B20_INTERNAL_PULLUP to select internal input pullup when only one DS18B20 sensor is connected eliminating external resistor (#4738)
• Add button control when no relay configured (#4682)
• Add startup delay of 4 seconds to button control (#4829)
• Add core version conditional compile options to provided PWM files (#4917)
• Add resiliency to saved Settings (#5065)
• Add MHZ19 Temperature as Domoticz Temperature selection (#5128)
• Add HAss status sensor (#5139)
• Add status message to former declined group commands (#5145)
• Add 0x to IRRemote (SetOption29) and RCSwitch (SetOption28) received hexadecimal data (#5431)

6.4.1 20181224

• Change RAM usage BMP/BME I2C sensors
• Change FallbackTopic from cmnd/<mqttclient>/ to cmnd/<mqttclient>_fb/ to discriminate from Topic (#1528)
• Change FallbackTopic detection (#4706)
• Change Hass discovery to short MQTT messages as used by Hass 0.81 and up (#4711)
• Change MQTT GUI password handling (#4723)
• Fix possible dtostrf buffer overflows by increasing buffers
• Fix wifi strongest signal detection (#4704)
• Fix Alexa "this value is outside the range of the device". Needs power cycle and Alexa deletion/discovery cycle. (#3159, #4712)
• Add Slovak language file (#4663)
• Add support for AZ-Instrument 7798 CO2 meter/datalogger (#4672)
• Add define WIFI_SOFT_AP_CHANNEL in my_user_config.h to set Soft Access Point Channel number between 1 and 13 as used by Wifi Manager web GUI (#4673)
• Add define USE_MQTT_TLS_CA_CERT for checking MQTT TLS against root ca using Let's Encrypt cert from sonoff_letsencrypt.h - not supported with core 2.3.0 (#4703)

6.4.0 20181217

• Change GUI Configure Module by using AJAX for data fetch to cut page size (and memory use) by 40% In case of web page errors clear your browser cache or do Page Reload (F5 or Ctrl+R)
• Change enforcing flashmode dout but it is still mandatory
• Change bootcount update (being first) flash write to 10 seconds after restart
• Change display and epaper drivers
• Change command WebSend Host header field from IP address to hostname (#4331)
• Change log buffer size from 512 to 520 to accommodate http sensor data (#4354)
• Change default WIFI_CONFIG_TOOL from WIFI_WAIT to WIFI_RETRY in my_user_config.h (#4400)
• Change webgui refresh time delay for Save Settings and local OTA Upload (#4423)
• Change SR-04 driver to use NewPing library (#4488)
• Change MCP230xx driver to support interrupt retention over teleperiod (#4547)
• Change support for MPU6050 using DMP (#4581)
• Fix unintended function overload of WifiState
• Fix wifi connection errors using wifi disconnect and ESP.reset instead of ESP.restart
• Fix Sonoff Pow R2 and Sonoff S31 Serial interface hang caused by Sonoff Basic R2 driver delay implementation (and possibly core bug)
• Fix MQTT connection error after restart
• Fix wifi re-scan connection baseline
• Fix possible strncat buffer overflows
• Fix intermittent Pzem sensor energy overflow calculation error
• Fix shelly2 ghost switching caused by lack of pull-up inputs (#4255)
• Fix hardware serial pin configuration. To keep using hardware serial swap current Rx/Tx pin configuration only (#4280)
• Fix MqttRetry values above 255 seconds (#4424)
• Fix WifiManager functionality on initial installation (#4433)
• Fix ArduinoOTA for Core 2.5.0 (#4620)
• Add minutes to commands Timezone to allow all possible world timezones
• Add more strict checks for GPIO selections
• Add code image and optional commit number to version
• Add dynamic delay to main loop providing time for wifi background tasks
• Add additional start-up delay during initial wifi connection
• Add support for decoding Theo V2 sensors as documented on https://sidweb.nl using 434MHz RF sensor receiver
• Add support for decoding Alecto V2 sensors like ACH2010, WS3000 and DKW2012 weather stations using 868MHz RF sensor receiver
• Add user definition of defines WIFI_RSSI_THRESHOLD (default 10) and WIFI_RESCAN_MINUTES (default 44)
• Add command SetOption58 0/1 to enable IR raw data info in JSON message (#2116)
• Add command IRSend |0,,,.. to allow raw data transmission (#2116)
• Add command SetOption56 0/1 to enable wifi network scan and select highest RSSI (#3173)
• Add command SetOption57 0/1 to enable wifi network re-scan every 44 minutes with a rssi threshold of 10 to select highest RSSI (#3173)
• Add support for SDM220 (#3610)
• Add default sleep 1 to sonoff-basic to lower energy consumption (#4217)
• Add wifi status to Tuya (#4221)
• Add delays to reduce CPU usage at boot time (#4233)
• Add command SetOption24 0/1 to select pressure unit as hPa or mmHg (#4241)
• Add optional hardware serial when GPIO13(Rx) and GPIO15(Tx) are selected removing hardware serial from GPIO01(Tx) and GPIO03(Rx) (#4288)
• Add support for Gosund SP1 v2.3 Power Socket with Energy Monitoring (#4297)
• Add support for Armtronix dimmers. See wiki for info (#4321)
• Add to command WebSend option to send a direct path when command starts with a slash (#4329)
• Add support for LG HVac and IrRemote (#4377)
• Add initial support for Hass sensor discovery (#4380)
• Add support for Fujitsu HVac and IrRemote (#4387)
• Add support for I2C MGC3130 Electric Field Effect sensor by Christian Baars (#3774, #4404)
• Add command CalcRes to set number of decimals (0 - 7) used in commands ADD, SUB, MULT and SCALE (#4420)
• Add CPU average load to state message (#4431)
• Add command SetOption59 0/1 to change state topic from tele/STATE to stat/RESULT (#4450)
• Add support for SM Smart Wifi Dimmer PS-16-DZ (#4465)
• Add support for Teckin US Power Socket with Energy Monitoring (#4481)
• Add command SetOption60 0/1 to select dynamic sleep (0) or sleep (1) (#4497)
• Add support for iFan02 Fanspeed in Domoticz using a selector (#4517)
• Add support for GPIO02 for newer Sonoff Basic (#4518)
• Add Announce Switches to MQTT Discovery (#4531)
• Add support for Manzoku Power Strip (#4590)

6.3.0 20181030

• Change web Configure Module GPIO drop down list order for better readability
• Change status JSON message providing more switch and retain information
• Change xsns_17_senseair.ino to use TasmotaModbus library
• Change MCP230xx driver
• Change PubSubClient Mqtt library to non-blocking EspEasy version
• Change energy monitoring using energy sensor driver modules
• Change Webserver page handler for easier extension (thx to Adrian Scillato)
• Change pinmode for no-pullup defined switches to pullup when configured as switchmode PUSHBUTTON (=3 and up) (#3896)
• Change default OTA Url to http://thehackbox.org/tasmota/release/sonoff.bin (#4170)
• Remove support for MQTT Client esp-mqtt-arduino by #define MQTT_LIBRARY_TYPE MQTT_ESPMQTTARDUINO
• Remove commands PowerCal, VoltageCal and CurrentCal as more functionality is provided by commands PowerSet, VoltageSet and CurrentSet
• Remove restart after ntpserver change and force NTP re-sync (#3890)
• Fix showing Period Power in energy threshold messages
• Fix header file execution order by renaming user_config.h to my_user_config.h
• Fix some TSL2561 driver issues (#3681)
• Fix KNX PA exception. Regression from 6.2.1 buffer overflow caused by subStr() (#3700, #3710)
• Fix setting and getting color temperature for Philips Hue emulation (#3733)
• Fix ButtonRetain to not use default topic for clearing retain messages (#3737)
• Fix syslog when emulation is selected (#2109, #3784)
• Fix rule trigger POWER1#STATE execution after restart and SetOption0 is 0 (#3856)
• Fix Home Assistant forced light discovery (#3908)
• Fix invalid configuration restores and decode_config.py crc error when savedata = 0 (#3918)
• Fix timer offset -00:00 causing 12:00 hour offset (#3923)
• Fix I2CScan invalid JSON error message (#3925)
• Fix exception when wrong Domoticz JSON message is received (#3963)
• Fix Sonoff Bridge RfRaw receive (#4080, #4085)
• Fix possible wifi connection error (#4044, #4083)
• Fix invalid JSON floating point result from nan (Not a Number) and inf (Infinity) into null (#4147)
• Fix rule mqtt#connected trigger when mqtt is disabled (#4149)
• Add support for LCD, Matrix, TFT and Oled displays
• Add support for Neo Coolcam Wifi Smart Power Plug
• Add support for Michael Haustein ESP Switch
• Add support for MQTT Client based on lwmqtt to be selected by #define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT
• Add support for Neo Coolcam Wifi Smart Power Plug
• Add support for Michael Haustein ESP Switch
• Add support for MQTT Client based on lwmqtt to be selected by #define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT
• Add support for DS3231 Real Time Clock
• Add support for HX711 Load Cell with optional web GUI scale interface to demonstrate easy GUI plug-in
• Add support for serial 8N2 communication to TasmotaModbus and TasmotaSerial libraries
• Add support for RF transceiving using library RcSwitch (#2702)
• Add support for Shelly 1 and Shelly 2 (#2789)
• Add support for La Crosse TX20 Anemometer (#2654, #3146)
• Add support for MP3 player using DFRobot RB-DFR-562 (#3723)
• Add Support for Xiaomi-Philips Bulbs (#3787)
• Add support for PCA9685 12bit 16pin hardware PWM driver (#3866)
• Add support for EXS Relay V5.0 (#3810)
• Add support for OBI Power Socket (#1988, #3944)
• Add support for Teckin Power Socket with Energy Monitoring (#3950)
• Add support for Pzem-003/017 DC Energy monitoring module (#3694)
• Add support for Pzem-014/016 AC Energy monitoring module (#3694)
• Add support for CSL Aplic WDP 303075 Power Socket with Energy Monitoring (#3991, #3996)
• Add support for Tuya Dimmer (#469, #4075)
• Add command Display to show all settings at once
• Add command SerialSend5 to send raw serial data like "A5074100545293"
• Add command WebRefresh 1000..10000 to control web page refresh in milliseconds. Default is 2345
• Add command WeightRes 0..3 to control display of decimals for kilogram
• Add command RGBWWTable to support color calibration (#3933)
• Add command Reset 4 (reset to defaults but keep wifi params) and Reset 5 (as reset 4 and also erase flash) (#4061)
• Add command SetOption35 0..255 (seconds) to delay mDNS initialization to control possible Wifi connect problems
• Add command SetOption52 0/1 to control display of optional time offset from UTC in JSON messages (#3629, #3711)
• Add command SetOption53 0/1 to toggle gui display of Hostname and IP address (#1006, #2091)
• Add authentication to HTTP web pages
• Add decimals as input to commands PowerSet, VoltageSet and CurrentSet
• Add tools/decode-config.py by Norbert Richter to decode configuration data. See file for information
• Add define USE_DISPLAYS for selecting image sonoff-display
• Add define USE_BASIC for selecting image sonoff-basic without most sensors
• Add auto reload of main web page to some web restarts
• Add TasmotaModbus library as very basic modbus wrapper for TasmotaSerial
• Add more API callbacks and document API.md
• Add Apparent Power and Reactive Power to Energy Monitoring devices (#251)
• Add token %hostname% to command FullTopic (#3018)
• Add Wifi channel number to state message (#3664)
• Add user configurable GPIO02 and GPIO03 on H801 devices (#3692)
• Add toggle function RGBW lights (#3695, #3697)
• Add network information to display start screen (#3704)
• Add sleep to Nova Fitness SDS01X sensor (#2841, #3724, #3749)
• Add Analog input AD0 enabled to sonoff-sensors.bin (#3756, #3757)
• Add power value below 5W to Sonoff Pow R2 and S31 (#3745)
• Add RF Receiver control to module MagicHome to be used on Arilux LC10 (#3792)
• Add userid/password option to decode-status.py (#3796)
• Add delay after restart before processing rule sensor data (#3811)
• Add force_update to Home Assistant discovery (#3873)
• Add rule triggers SWITCH1#BOOT and POWER1#BOOT (#3904, #3910)
• Add Hebrew language file (#3960)
• Add TotalStartTime to Energy JSON message (#3971)
• Add whitespace removal from RfRaw and SerialSend5 (#4020)
• Add support for two BMP/BME sensors (#4195)

6.2.1 20180905

• Fix possible ambiguity on command parameters if StateText contains numbers only (#3656)
• Fix Wemo emulation to select the first relay when more than one relay is present (#3657)
• Fix possible exception due to buffer overflow (#3659)
• Fix lost energy today and total energy value after power cycle (#3689)

6.2.0 20180901

• Allow user override of define MAX_RULE_VARS and MAX_RULE_TIMERS (#3561)
• Disable wifi sleep for both Esp8266/Arduino core 2.4.1 and 2.4.2 to solve device freeze caused by Espressif SDK bug (#3554)
• Change DS18B20 driver to provide better instant results
• Change some sensor drivers to provide instant results
• Change define USE_ALL_SENSORS to USE_SENSORS as it doesn't contain all sensors due to duplicate I2C addresses
• Change some sensor update timings: AdcEvery 200 -> 250, Senseair 300 -> 250, SDM120 300 -> 250, SDM630 300 -> 250
• Change default Wifi config option from WPS to Wifi Manager if WPS is disabled or Wifi Smartconfig if webserver is disabled or Wifi Serial input if Smartconfig is disabled
• Change SHT1x driver to provide better instant results and fix I2C interference
• Change DHT driver to provide better instant results and add decimals to DHT11 (#3164)
• Change DS18x20 driver to provide better instant results (#3169)
• Change CounterType 1 from milliseconds to microseconds (#3437)
• Change scheduler for better sleep support using Uptime, Delay, PulseTime and TelePeriod, Blinktime (#3581)
• Remove unused functionality from Sonoff-minimal to save space
• Remove WPS and SmartConfig from sonoff-minimal saving 56k code space
• Remove TSL2561 debug message and update library (#2415)
• Remove forced restart when sleep command is executed (#3554)
• Fix invalid response using more than 4 switches and domoticz
• Fix sonoff-minimal not using default settings
• Fix insecure main webpage update
• Fix DHT driver mixing values for different sensors (#1797)
• Fix EnergyReset3 regression not clearing total energy (#2723)
• Fix rules once regression from v6.1.0 (#3198, #3226)
• Fix command Scale buffer overflow (#3236)
• Fix possible WDT due to long MQTT publish handling (#3313)
• Fix command TimeDst/TimeStd invalid JSON (#3322)
• Fix handling of default names when using names starting with shortcut character ",0,1 or 2 (#3392, #3600, #3618)
• Fix LM75AD I2C sensor detection (#3408)
• Fix iFan02 power on state (#3412, #3530)
• Fix some Pow R2 and S31 checksum errors using optimized re-sync (#3425)
• Fix SDM120 reporting wrong negative values to Domoticz (#3521)
• Fix MQTT reconnection detection when using TasmotaMqtt library (#3558)
• Fix OtaMagic when file path contains a dash (-) (#3563)
• Fix Sonoff Bridge data reception when using Portisch EFM8 firmware using in data buffer length (#3605)
• Add read sensor retry to DS18B20, DS18x20, DHT, SHT1X and HTU21
• Add user selection of Wifi Smartconfig as define USE_SMARTCONFIG in user_config.h
• Add boot loop detection and perform some solutions
• Add wifi and mqtt status led blinkyblinky to be disabled by SetOption31 1. Does not work when LedPower is On (deliberate) (#871, #2230, #3114, #3155)
• Add support for TM1638 switch (#2226)
• Add GPIO options ButtonXn, SwitchXn and CounterXn to select INPUT mode instead of INPUT_PULLUP (#2525)
• Add support for APDS9960 proximity sensor (#3051)
• Add support for MPR121 controller in input mode for touch buttons (#3142)
• Add support for MCP230xx for general purpose input expansion and command Sensor29 (#3188)
• Add default Wifi Configuration tool as define WIFI_CONFIG_NO_SSID in user_config.h if no SSID is configured (#3224)
• Add command Timers 0/1 to globally disable or enable armed timers (#3270)
• Add support for CCS811 sensor (#3309)
• Add Turkish language file (#3332)
• Add command SerialSend4 to send binary serial data (#3345)
• Add initial support for sensor MPU6050 (#3352)
• Add rule triggers Wifi#Connected and Wifi#Disconnected (#3359)
• Add option + to command Rule to concatenate new rule with existing rules (#3365)
• Add message when JavaScript is not enabled in webbrowser (#3388)
• Add build time setting of ButtonTopic and SwitchTopic (#3414)
• Add iFan02 Fanspeed + and Fanspeed - command options (#3415)
• Add Individual HSBColorX commands (#3430, #3615)
• Add output support on MCP23008/MCP23017 (#3436)
• Add modulo option to rules like rule1 on Time#Minute|5 do backlog power on;delay 200;power off endon (#3466)
• Add RGB support for Domoticz (#3547)
• Add all ruletimer values to command RuleTimer result message (#3571)
• Add command Publish2 for publishing retained MQTT messages (#3593)
• Add commands ButtonDebounce 40..1000 and SwitchDebounce 40..1000 to have user control over debounce timing. Default is 50mS (#3594)
• Add RuleX debug options 8,9,10 (StopOnError) to control RuleX execution status after an exception restart (#3607)
• Add rule variables %sunrise%, %sunset%, %uptime% and %time% (#3608)
• Add optional MQTT_TELE_RETAIN to Energy Margins message (#3612, 3614)

6.1.1 20180714

• Revert wifi changes (#3177)
• Revert sonoff-minimal removals causing failure of wifi connection (#3177)

6.1.0 20180706

• Remove version 3, 4 and pre 5.2 settings auto-upgrade. See https://github.com/arendst/Tasmota/wiki/Upgrading#migration-path
• Change default CFG_HOLDER from 0x20161209 to 4617 (=0x1209) - no impact on default upgrades
• Change number of supported switches from 4 to 8 (#2885, #3086)
• Change BME680 driver from Adafruit to Bosch BME680 library (#2969)
• Fix Pzem004T checksum error
• Fix KNX bug when doing reply of sensors values
• Fix rules induced LWT message
• Fix possible wifi connection problem (#1366)
• Fix some Pow R2 and S31 checksum errors (#1907)
• Fix display selection of un-available GPIO options in Module Configuration webpage (#2718)
• Fix timer re-trigger within one minute after restart (#2744)
• Fix IRSend not accepting data value of 0 by David Conran (#2751)
• Fix vars on rules by Adrian Scillato (#2769)
• Fix bug in KNX menu by Adrian Scillato (#2770)
• Fix anomalies in rules (#2778)
• Fix HUE bridge V1 software version by Heiko Krupp (#2788)
• Fix Hardware Watchdog restart when using event command (#2853)
• Add Ukrainian language file
• Add KNX support for DS18S20 Temperature sensor
• Add CRC to Settings making future upgrades more fail-safe
• Add feature information to Status 4
• Add tools folder with python script decode-status.py for decoding some status fields like SetOption and Features
• Add Slots on the KNX Web Menu to select Group Address to receive data to trigger rules
• Add two rule sets of 511 characters using commands rule1, rule2 and rule3
• Add Console Commands to send KNX Commands and KNX Values
• Add Slots on the KNX Web Menu to select Group Address to send data from console commands
• Add Events to trigger rules when a command or read requests is received from KNX
• Add command SetOption30 to enforce Hass discovery as light group (#1784)
• Add support for BlitzWolf BW-SHP2 (and Homecube, Gosund SP1) Energy Monitoring Smart Socket (#2223)
• Add time in minutes to rule Time#Initialized, Time#set and Time#Minute (#2669)
• Add Eastron SDM630 energy meter by Gennaro Tortone (#2735)
• Add KNX communication enhancement by Adrian Scillato (#2742)
• Add KNX energy data by Adrian Scillato (#2750)
• Add rule support for IrReceive and RfReceive (#2758)
• Add python script fw-server.py in tools folder to create a simple OTA server by Gennaro Tortone (#2759)
• Add rule variables %time% for minutes since midnight, %uptime%, %sunrise% and %sunset% giving time in minutes (#2669)
• Add rules %mem1% to %mem5% variable names storing data in flash (#2780)
• Add rules test on %varx% or %memx% (#2780)
• Add optional token %id% substituting the unique MAC address to fulltopic by Michael Graf (#2794)
• Add support for Sonoff S26 Smart Socket (#2808)
• Add command WebSend [(:,:)] (#2821)
• Add increment and decrement value to command Counter (#2838)
• Add support for Sonoff iFan02 as module 44 introducing command FanSpeed 0..3 (#2839)
• Add source information to command execution to be shown with logging option 3 (#2843)
• Add support for uploading Sonoff Bridge firmware found in tools/fw_efm8bb1 folder build by Portisch using Web Gui File Upload (#2886)
• Add command RfRaw to control Portisch firmware features
• Add support for I2C temperature sensor LM75AD (#2909)
• Add option 0 to command Timers disarming all timers (#2962)
• Add performance improvement when updating multiple individual WS2812 pixels (#3007)
• Add command SetOption28 to switch between hex or decimal Sonoff Bridge RF received data format (#3008)
• Add command SetOption29 to switch between hex or decimal IR received data format
• Add decimal values support for commands ADD, SUB, MULT and SCALE (#3083, #3089)
• Add support for bitflags SetOption50 .. SetOption81 (#3118)

5.14.0 20180515

• Update language files
• Update TasmotaSerial to 2.0.0 allowing Hardware Serial Fallback when correct connections are configured
• Change command handling
• Change user_config(_override).h defines TIME_STD and TIME_DST
• Change user_config(_override).h otaurl to http://sonoff.maddox.co.uk/tasmota/sonoff.bin (#2588, #2602)
• Fix configuration restore regression from 5.13.1
• Fix compile error when ADC is enabled and Rules are disabled (#2608)
• Fix rule power trigger when no backlog command is used (#2613)
• Fix several timer data input and output errors (#2597, #2620)
• Fix KNX config error (#2628)
• Fix sensor MHZ-19 vanishing data over time (#2659)
• Fix KNX reconnection issue (#2679)
• Fix DST and STD time for Southern Hemisphere by Adrian Scillato (#2684, #2714)
• Add Portuguese in Brazil language file
• Add SetOption26 to enforce use of indexes even when only one relay is present (#1055)
• Add support for sensor SI1145 UV Index / IR / Visible light (#2496)
• Add rule state test for On/Off in addition to 0/1 (#2613)
• Add hardware serial option to MHZ-19 sensor (#2659)
• Add Eastron SDM120 energy meter by Gennaro Tortone (#2694)
• Add user entry DST/STD using commands TimeStd and TimeDst (See wiki for parameter syntax) (#2721)

5.13.1 20180501

• Fix JSON buffers size too small for execution in some situations (#2580)
• Fix configuration restore (#2591)
• Add define MODULE for user selecting default model although it preferably should not be changed (#569, #2589)

5.13.0 20180430

• Change platformio option sonoff-ds18x20 to sonoff-allsensors enabling ds18x20 and all other sensors in one image
• Change status display of Ssid and SetOption
• Change default option SetOption15 from 0 to 1 providing better initial PWM experience
• Change webpage parameter communication
• Change max number of commands in Backlog from 15 to 30 and ignore commands overflowing
• Change TSL2561 driver to joba library and delete Adafruit library (#1644)
• Change default parameters in user_config.h to undefined for easy installation (#1851)
• Change max user configurable hold time from 10 to 25 seconds (#1851)
• Change Sonoff SC JSON format (#1939)
• Change Polish language to using Diacritics (#2005)
• Change user_config_override usage by providing user_config_override_sample.h (#2228)
• Change MQTT response topic for Energy changes from ENERGY to SENSOR (#2229, #2251)
• Change default Reset configuration time from 4 seconds to 40 seconds on Button hold (#2268)
• Change ESP8266 Analog JSON message from {"Analog0:123"} to {"ANALOG":{"A0:123"}} to accommodate rules (#2560)
• Change Counter JSON message from {"Counter1":0,"Counter3":0} to {"COUNTER":{"C1":0,"C3":0}} to accommodate rules
• Change ADS1115 JSON message from {"ADS1115":{"Analog0":123,"Analog1":123}} to {"ADS1115":{"A0":123,"A1":123}}
• Fix intermittent exception when dns lookup is used while sleep is enabled
• Fix 5.4.0 regression turning off single press after button hold during 4x hold time
• Fix possible wifi connection problem by erasing sdk configuration parameters
• Fix NTP sync to Thu Jan 01 08:00:10 1970 results in uptime 17651+ days (core2.4.1/sdk2.2.1)
• Fix MAX31850 higher temperatures (#1269)
• Fix freeing more code space when emulation is disabled (#1592)
• Fix providing web page configuration option for Friendly Name when no device (relay or light) is configured (#1850)
• Fix compile error when define HOME_ASSISTANT_DISCOVERY_ENABLE is not set (#1937)
• Fix MQTT TLS fingerprint validation (#2033)
• Fix update temperature on DS18x20 drivers (#2328)
• Fix compile error when not defined USE_TIMERS (#2400)
• Fix configuration filename truncation when it contains spaces (#2484, #2490)
• Fix Energy Today and Yesterday overflow (#2543)
• Add serial debug info
• Add Portuguese language file
• Add Czech language file
• Add Bulgarian language file
• Add Domoticz dust (custom) sensors to PMS5003 and NovaFitness SDS drivers as PM1, PM2.5 and PM10
• Add commands Publish, Rule, RuleTimer and Event. See Wiki about Rule restriction, usage and examples
• Add sonoff-classic, sonoff-allsensors and sonoff-knx
• Add some coloring to important web buttons
• Add support for sensor HC-SR04 ultrasonic (#113, #1964, #2444)
• Add define MQTT_TELE_RETAIN compile option default set to 0 (#1071)
• Add 16 timers using commands Timer and Timers (#1091)
• Add optional Timer configuration webpage to be enabled in user_config.h with define USE_TIMERS_WEB
• Add Multichannel Gas sensor using MultiChannel_Gas_Sensor library (#1245)
• Add Domoticz Battery and RSSI Quality (#1604)
• Add command HSBColor Hue,Sat,Bri (#1642, #2203)
• Add compile time support for WS2812 BRG and RBG led configurations to be defined in user_config.h (#1690)
• Add optional usage of %d or %X suffices in MQTT client to append chipid (#1871)
• Add optional usage of %d or %X suffices in MQTT topic to append chipid (#1871)
• Add optional usage of %d or %04d in ota url to be replaced with chipid (#1871)
• Add Sonoff Bridge command RfKey 5 to show current RF key values either default or learned (#1884)
• Add user configurable serial GPIOs to MagicHome and Arilux modules (#1887)
• Add Russian language file (#1909)
• Add Webserver upload preflight request support (#1927)
• Add Home Assistant clear other device (#1931)
• Add Restart time to Status 1 (#1938)
• Add optional TSL2561 driver using library Joba_Tsl2561 to be enabled in user_config.h with define USE_TSL2561_JOBA (#1951)
• Add support for sensor SHTC3 (#1967)
• Add compiler check for stable lwIP version v1.4 (#1940)
• Add support for multiple SHT3X sensors (#1949, #2110)
• Add always suffix with device number in Mqtt discovery topic (#1962)
• Add support for optional MQTT drivers to be selected in user_config.h (#1992)
• Add optional Arduino OTA support to be enabled in user_config.h (#1998)
• Add diacritics to Polish language file (#2005)
• Add Hungarian language file (#2024)
• Add support for Nova Fitness SDS011 and possibly SDS021 particle concentration sensor (#2070)
• Add single decimal precision to Nova Fitness SDS0x1 sensor values (#2093)
• Add Chinese (Traditional) in Taiwan language file (#2108)
• Add Sonoff SC domoticz support for Sound level as Counter and Air quality (#2118)
• Add a second TLS fingerprint to allow switching keys in TLS mode (#2033, #2102)
• Add display of remaining pulse time to command PulseTime (#2085)
• Add additional time offset to Wifi Retry based on device mac address (#2089)
• Add command Color6 RRGGBB for Clock hour marker color and command Rotation pixels for Clock rotation (#2092)
• Add HTML language header in local language (#2123)
• Add command PowerDelta 0..100 (percentage) to Energy monitoring devices to report on active power load change (#2157)
• Add Restart Reason to Status 1 report (#2161)
• Add command Channel 0..100 to control dimmer value for individual color channels (#2111, #2203)
• Add support for Hardware Serial bridge using commands SerialDelimiter, Baudrate and SerialSend. Supports 8N1 and text only (#2182)
• Add support for Software Serial bridge using commands SerialDelimiter, SBaudrate and SSerialSend. Supports 8N1 and text only (#2190)
• Add support for Zengge WF017 PWM Led strip controller (#2202)
• Add PWM status to command State if PWM enabled (#2203)
• Add all FriendlyNames to Status information (#2208)
• Add Channel status information (#2211)
• Add hexadecimal Data entry to command IrSend using 0x notation (#1290, #2314)
• Add Home Assistant MQTT Discovery for Buttons and change SetOption19 response (#2277)
• Add multiple color entry support for command Led like Led2 120000 001200 000012 setting led2 as Red, Led3 as Green and Led4 as Blue (#2303)
• Add hexadecimal RGB color entry on RGBCW leds (#2304)
• Add support for SGP30 gas and air quality sensor (#2307)
• Add optional Sunrise and Sunset timers with commands Latitude and Longitude to be enabled with define USE_SUNRISE in user_config.h (#2317)
• Add timer sunrise and sunset offset (#2378)
• Add user selectable defines for Sunrise/set Dawn option (#2378)
• Add optional KNX IP Protocol Support (#2402)
• Add random window to timers (#2447)
• Add Greek language file (#2491)
• Add support for Sonoff Pow R2 (#2340)
• Add GPIO_User to GPIO02 for all Sonoff T1 (#2524)

5.12.0 20180209

• Change library PubSubClient.h define MQTT_MAX_PACKET_SIZE from 512 to 1000 for Home Assistant support
• Change relation of define MESSZ being dependent on PubSubClient.h define MQTT_MAX_PACKET_SIZE
• Change command color parameter input checks to less strict for Home Assistant support
• Change command Ina219Mode into command Sensor13
• Change commands HlwPCal, HlwUCal and HlwICal to PowerCal, VoltageCal and CurrentCal to be used for both Pow and S31 calibration
• Change commands HlwPSet, HlwUSet and HlwISet to PowerSet, VoltageSet and CurrentSet to be used for both Pow and S31 calibration
• Change uptime from hour to second resulting in a display of 123T13:45:21 where 123 is days
• Change module name Wemos D1 mini into Generic (#1220)
• Change HTML from width=100% to style=width:100% supporting HTML5 (#1358)
• Change OSWATCH_RESET_TIME (Blocked loop) from 30 to 120 seconds to allow slow networks (#1556)
• Change WIFI_MANAGER_SEC into WIFI_CONFIG_SEC (#1616)
• Change function pointers code to save code space and memory (#1683)
• Change webserver argument processing gaining 5k code space (#1705)
• Change weblog memory usage (#1730, #1793, #1819)
• Update TasmotaSerial library to 1.1.0
• Update language files Italian (#1594), Dutch (#1723) and Spanish (#1722)
• Fix Non-English JSON temperature unit attachment
• Fix Arilux RF induced exception by moving interrupt handler to iram on non ESP8266/Arduino lib v2.3.0
• Fix truncated command names and wrong response for DomoticzSwitchIdx (#1571)
• Fix %-sign issue as printf escape character in Humidity and Sonoff SC (#1579)
• Fix DS18B20 temperature JSON decimal dot (#1561)
• Fix Energy JSON message (#1621)
• Fix IRSend parameter translation (#1636)
• Fix TSL2561 device detection (#1644, #1825)
• Fix BME680 teleperiod resistance measuring (#1647)
• Fix Energy Monitoring Energy Today and Energy Total reading after restart (#1648)
• Fix IRReceive Data value (#1663)
• Fix Energy Monitoring Energy Period roll-over (#1688)
• Fix compiler warnings (#1774)
• Fix command PWM response if no PWM channel is configured (#1783)
• Add locale Decimal Separator to Web sensor page
• Add ColorTemperature to light status message
• Add command PowerOnState option 5 which inverts PulseTime and allows for delayed always on after power on
• Add OtaMagic two step Web server OTA upgrade using filename-minimal image if OTA free space is too small
• Add support for PMS5003 and PMS7003 particle concentration sensor
• Add command SetOption21 1 to allow Energy Monitoring when power is off on Sonoff Pow and Sonoff S31 (#1420)
• Add Chinese language file (#1551)
• Add French language file (#1561)
• Add Spanish language file (#1589)
• Add HTTP Allow Cross Origin removed from ESP8266/Arduino lib v2.4.0 (#1572)
• Add Home Assistant MQTT Discovery for switch and light to be enabled by command SetOption19 1 (#1534) or define HOME_ASSISTANT_DISCOVERY_ENABLE in user_config.h (#1685)
• Add command State to retrieve device state information (same data as teleperiod state and status 11 in slightly different JSON format)
• Add optional login to Webserver AP mode (#1587, #1635)
• Add command Sensor15 2 to start MHZ19(B) Zero Point Calibration (#1643)
• Add support for Sonoff S31 Smart Socket with Power Consumption Detection (#1626)
• Add command SetOption20 to allow update of Dimmer/Color/Ct without turning power on (#1719, #1741)
• Add NTP sync time slot based on chip id (#1773)
• Add cursor pointer to web button (#1836)

5.11.1 20180107

• Fix Sonoff Pow command handling (#1542)

5.11.0 20180107

• Minor webpage HTML optimizations (#1358)
• Updated German translation (#1438)
• Change Sonoff Pow Energy MQTT data message and consolidate Status 8 into Status 10
• Change ADS1115 default voltage range from +/-2V to +/-6V (#1289)
• Change text to Active for 3 minutes (#1364)
• Change Wemo SetBinaryState to distinguish from GetBinaryState (#1357)
• Change output of HTTP command to valid JSON and Array only (#1363)
• Removed all MQTT, JSON and Command language defines from locale files and set fixed to English (#1473)
• Renamed commands Color2,3,4 to Color3,4,5
• Fix BME280 calculation (#1051)
• Fix Sonoff Bridge missed learned key if learned data contains 0x55 (End of Transmission) flag (#1095, #1294)
• Fix PWM initialization in Dimmer/Color mode (#1321)
• Fix Wemo Emulation (#1357)
• Fix display of build date and time in non-english locale (#1465)
• Fix Wemo and Hue emulation by adding M-Search response delay (#1486)
• Add libraries Adafruit_BME680-1.0.5, Adafruit_Sensor-1.0.2.02, TasmotaSerial-1.0.0 and TSL2561-Arduino-Library
• Add command Color2 to set color while keeping same dimmer value
• Add device function pointers
• Add support for SenseAir S8 CO2 sensor
• Add color led signal to Carbon Dioxide (CO2) sensors using defines CO2_LOW and CO2_HIGH in user_config.h
• Add support for Domoticz Air Quality sensor to be used by MH-Z19(B) and SenseAir sensors
• Add support for PZEM004T energy sensor
• Add support for iTead SI7021 temperature and humidity sensor by consolidating DHT22 into AM2301 and using former DHT22 as SI7021 (#735)
• Add support for BME680 using adafruit libraries (#1212)
• Add support for MH-Z19(B) CO2 sensor (#561, #1248)
• Add multipress support and more user configurable GPIO to Sonoff Dual R2 (#1291)
• Add support for TSL2561 using adafruit library (#661, #1311)
• Add support for SHT3x (#1314)
• Add support for Arilux LC06 (#1414)
• Add Italian language file (#1449)
• Add 2nd Gen Alexa support to Wemo emulation discovery (#1357, #1450)
• Add define for additional number of WS2812 schemes (#1463)

5.10.0 20171201

• Upgrade library ArduinoJson to 5.11.2
• Upgrade library IRRemoteEsp8266 to 2.2.1 + 2 commits but disabled some protocols (code size reduction)
• Upgrade library NeoPixelBus to 2.2.9
• Upgrade library OneWire to 2.3.3 + 6 commits and disabled CRC lookup-table (#define ONEWIRE_CRC8_TABLE 0) (code size reduction)
• Update library PubSubClient to 2.6 + 9 commits and additional delay (#790)
• Update core_esp8266_wiring_digital.c to latest (staged) level
• Patch library I2Cdevlib-Core for esp8266-core 2.4.0-rc2 compatibility
• Remove command EnergyReset 1..3 now replaced by EnergyReset1 to EnergyReset3
• Remove spaces in JSON messages (code size reduction)
• Renamed xsns_05_ds18x20.ino to xsns_05_ds18x20_legacy.ino still using library OneWire and providing dynamic sensor scan
• Fix possible iram1_0_seg compile error by shrinking ICACHE_RAM_ATTR code usage
• Fix PWM watchdog timeout if Dimmer is set to 100 or Color set to 0xFF (#1146)
• Fix Sonoff Bridge Learn Mode hang caused by unrecognised RF code (#1181)
• Fix blank console log window by using XML character encoding (#1187)
• Fix wrong response name for command HlwISet (#1214)
• Fix DHT type sensor timeout recognition by distinguish "signal already there" from "timeout" (#1233)
• Add fixed color options 1..12 to command Color
• Add + (plus) and - (minus) to commands Dimmer (+10/-10), Speed and Scheme
• Add + (plus) and - (minus) to command Color to select 1 out of 12 preset colors
• Add + (plus) and - (minus) to command Ct to control ColdWarm led ColorTemperature (+34/-34)
• Add commands EnergyReset1 0..42500, EnergyReset2 0..42500 and EnergyReset3 0..42500000
• to (Re)set Energy Today, Yesterday or Total respectively in Wh (#406, #685, #1202)
• Add optional ADS1115 driver as alternative for unsupported I2Cdevlib in esp8266-core 2.4.0-rc2
• Add support for INA219 Voltage and Current sensor to be enabled in user_config.h with define USE_INA219
• Add support for Arilux LC11 (Clearing RF home code when selecting no Arilux module)
• Add support for WS2812 RGBW ledstrips to be enabled in user_config.h with define USE_WS2812_CTYPE (#1156)
• Add SettingsSaveAll routine to command SaveData to be used before controlled power down (#1202)
• Add option PUSHBUTTON_TOGGLE (SwitchMode 7) to allow toggling on any switch change (#1221)
• Add new xdrv_05_ds18x20.ino free from library OneWire and add the following features:
• Add support for DS1822
• Add forced setting of 12-bit resolution for selected device types (#1222)
• Add read temperature retry counter (#1215)
• Fix lost sensors by performing sensor probe at restart only thereby removing dynamic sensor probe (#1215)
• Fix sensor address sorting using ascending sort on sensor type followed by sensor address
• Rewrite JSON resulting in shorter message allowing more sensors in default firmware image:
• "DS18B20-1":{"Id":"00000483C23A","Temperature":19.5},"DS18B20-2":{"Id":"0000048EC44C","Temperature":19.6}
• Add additional define in user_config.h to select either single sensor (defines disabled), new multi sensor (USE_DS18X20) or legacy multi sensor (USE_DS18X20_LEGACY)
• Add clock support for more different pixel counts (#1226)
• Add support for Sonoff Dual R2 (#1249)
• Add FriendlyName to web page tab and add program information to web page footer (#1275)

5.9.1 20171107

• Add external sensor function pointer interface to enable easy sensor addition
• Add support for ADS1115 to be enabled in user_config.h and needs libraries i2cdevlib-Core and i2cdevlib-ADS1115 (#338, #660)
• Fix Backup Configuration file download failure by defining proper file size (#1115)
• Fix Exception 26 and empty console screen after usage of command WakeupDuration (#1133)
• Fix some changed iTead web links in README.md (#1137)

5.9.0 20171030

• Rewrite code (partly) using Google C++ Style Guide (https://google.github.io/styleguide/cppguide.html)
• Rewrite code by using command lookup tables and javascript (client side) web page expansions
• Change HTML/CSS to enable nicer form field entry
• Change default PWM assignments for H801 RGB(CW) led controller to support optional Color/Dimmer control
• GPIO04 (W2) from GPIO_PWM2 to GPIO_USER to be user configurable for GPIO_PWM5 (second White - Warm if W1 is Cold)
• GPIO12 (Blue) GPIO_PWM3 no change
• GPIO13 (Green) from GPIO_PWM4 to GPIO_PWM2
• GPIO14 (W1) from GPIO_PWM1 to GPIO_USER to be user configurable for GPIO_PWM4 (first White - Cold or Warm)
• GPIO15 (Red) from GPIO_PWM5 to GPIO_PWM1
• Change default PWM assignments for MagicHome RGB(W) led controller to support optional Color/Dimmer control
• GPIO05 (Green) from GPIO_PWM4 to GPIO_PWM2
• GPIO12 (Blue) from GPIO_PWM5 to GPIO_PWM3
• GPIO13 (White) GPIO_USER to be user configurable for GPIO_PWM4 (White - Cold or Warm)
• GPIO14 (Red) from GPIO_PWM3 to GPIO_PWM1
• Change default PWM assignment for Witty Cloud to support optional Color/Dimmer control (#976)
• GPIO12 (Green) from GPIO_PWM4 to GPIO_PWM2
• GPIO13 (Blue) from GPIO_PWM5 to GPIO_PWM3
• GPIO15 (Red) from GPIO_PWM3 to GPIO_PWM1
• Change when another module is selected now all GPIO user configuration is removed
• Change command name IRRemote to IRSend (#956)
• Remove Arduino IDE version too low warning as it interferes with platformio.ini platform = espressif8266_stage
• Fix command FullTopic entry when using serial or console interface
• Fix possible UDP syslog blocking
• Fix minimum TelePeriod of 10 seconds set by web page
• Fix command GPIOx JSON response (#897)
• Fix inverted relay power on state (#909)
• Fix compile error when DOMOTICZ_UPDATE_TIMER is not defined (#930)
• Fix alignment of web page items in some browsers (#935)
• Fix setting all saved power settings to Off when SetOption0 (SaveState) = 0 (#955)
• Fix timezone range from -12/12 to -13/13 (#968)
• Fix Southern Hemisphere TIME_STD/TIME_DST (#968)
• Fix TLS MQTT SSL fingerprint test (#970, #808)
• Fix virtual relay status message used with Color/Dimmer control (#989)
• Fix command IRSend and IRHvac case sensitive parameter regression introduced with version 5.8.0 (#993)
• Fix pressure calculation for some BMP versions regression introduced with version 5.8.0i (#974)
• Fix Domoticz Dimmer set to same level not powering on (#945)
• Fix Blocked Loop when erasing large flash using command reset 2 (#1002)
• Fix relay power control when light power control is also configured as regression from 5.8.0 (#1016)
• Fix Mqtt server mDNS lookup only when MqttHost name is empty (#1026)
• Add debug information to MQTT subscribe
• Add translations to I2Cscan
• Add translation to BH1750 unit lx
• Add light scheme options (Color cycle Up, Down, Random) and moving WS2812 schemes up by 3
• Add Domoticz counter sensor to IrReceive representing Received IR Protocol and Data
• Add option 0 to MqttHost to allow empty Mqtt host name
• Add support for Arilux AL-LC01 RGB Led controller (#370)
• Add esp8266 de-blocking to PubSubClient library (#790)
• Add Domoticz sensors for Voltage and Current (#903)
• Add platformio OTA upload support (#928, #934)
• Add warning to webpage when USE_MINIMAL is selected (#929)
• Add smoother movement of hour hand in WS2812 led clock (#936)
• Add support for Magic Home RGBW and some Arilux Led controllers (#940)
• Add command SetOption15 0 (default) for command PWM control or SetOption15 1 for commands Color/Dimmer control to PWM RGB(CW) leds (#941)
• Add Domoticz counter sensor to Sonoff Bridge representing Received RF code (#943)
• Add support for Luani HVIO board (https://luani.de/projekte/esp8266-hvio/) (#953)
• Add PWM initialization after restart (#955)
• Add IR Receiver support. Disable in user_config.h (#956)
• Add support for inverted PWM (#960)
• Add Sea level pressure calculation and Provide command Altitude (#974)
• Add support for up to 8 relays (#995)
• Add commands RfSync, RfLow, RfHigh, RfHost and RfCode to allow sending custom RF codes (#1001)
• Add retain to ENERGY messages controlled by command SensorRetain (#1013)
• Add commands Color2, Color3, Color4, Width2, Width3, Width4 and SetOption16 to set Ws2812 Clock parameters (#1019)
• Add German language file (#1022)
• Add support for connecting to MQTT brokers without userid and/or password (#1023)
• Add support for esp8266 core v2.4.0-rc2 (#1024)
• Add commands PwmRange 1,255..1023 and PwmFrequency 1,100..4000 (#1025)
• Add Polish language file (#1044, #1047)
• Add support for KMC 70011 Power Monitoring Smart Plug (#1045)
• Add support for VEML6070 I2C Ultra Violet level sensor (#1053)
• Add light turn Off Fade (#925)
• Add IrSend command option Panasonic as IrSend {"Protocol":"Panasonic", "Bits":16388, "Data":<Panasonic data>}
• where 16388 is 0x4004 hexadecimal (#1014)
• Add retry counter to DHT11/21/22 sensors (#1082)

5.8.0 20170918

• Remove the need for NeoPixelBus library for Hue support
• Consolidate WS2812 into Sonoff Led for flexible future led strip library changes
• Invert WS2812 fade speed to align with Sonoff led (Speed 1 = fast, Speed 8 = slow)
• Remove upper case MQTT receive buffer
• Reduce code and string length for output of commands Modules and GPIOs
• Add Sonoff SC debug information
• Change syslog service
• Removed webserver syslog disable as now no longer needed
• Increased default MQTT message size from 368 to 405 bytes while keeping MQTT_MAX_PACKET_SIZE = 512 (because we can)
• Fix MQTT Offline or Remove MQTT retained topic code
• Fix Domoticz loop when Emulation is selected
• Add blink to WS2812 and Sonoff Led (#643)
• Add option WIFI_WAIT (5) to command WifiConfig to allow connection retry to same AP without restart or update flash (#772, #869)
• Add support for Witty Cloud (#794)
• Add GPIO14 to Sonoff Dual (#797, #839)
• Add support for Yunshan Wifi Relay (#802)
• Add GPIO16 input pulldown (#827)
• Add timeout to DHT and DS18B20 sensors (#852)
• Fix watchdog timeout caused by lack of stack space by moving to heap (#853)
• Allow LogPort and MqttPort up to 65535 and add LogPort tot Status 3 (#859)
• Allow command SwitchTopic in group mode (#861)
• Allow command SwitchMode if no switches are defined (#861)
• Add optional dimmer parameter to command Wakeup for WS2812, AiLight, Sonoff B1, Led and BN-SZ01 (#867)
• Fix basic On, Off, Toggle, Blink and BlinkOff commands when other language is selected (#874)

5.7.1 20170909

• Remove leading spaces from MQTT data
• Fix webconsole special character entry
• Allow # as prefix for color value
• Fix Alexa detection and Hue App Update Request (#698, #854)

5.7.0 20170907

• Shrink module configuration webpage
• Fix settings order during startup to allow for displaying debug messages
• Fix some string length issues
• Add more string length tests by using strncpy
• Add Ai-Thinker RGBW led (AiLight)
• Add Power check and add PulseTime to power check at startup (#526)
• Add Supla Espablo support (#755)
• Add more precision to Sonoff Pow period and power results using command WattRes 0|1 (#759)
• Add basic internationalization and localization (#763)
• Add more Sonoff Pow range checking (#772)
• Fix invalid JSON (#786, #822)
• Add duplicate check to received RF signal within 2 seconds for Sonoff Bridge (#810)

5.6.1 20170818

• Change module list order in webpage
• Fix Sonoff T1 1CH and 2CH configuration (#751)

5.6.0 20170818

• Fix Sonoff Pow intermittent exception 0
• Change Sonoff Pow sending Domoticz telemetry data only
• Add Ai-Thinker RGBW led (AiLight) (experimental)
• Add NeoPixelBus library to Sonoff Led for Hue support
• Add user configurable GPIO4 and GPIO5 to module Sonoff Bridge
• Add Sonoff B1 RGBCW led support with command Color RRGGBBCCWW (#676)
• Add command CT 152..500 to Sonoff Led and Sonoff B1 to control Color Temperature
• Add Cold-Warm slider to web page for Sonoff Led and Sonoff B1
• Add CT parameter to Hue
• Add Sonoff T1 support (#582)
• Add AnalogInput0 if configured as Analog Input to webpage (#697, #746)
• Add command SetOption14 0|1 to enable interlock mode (#719, #721)
• Fix Mitsubishi HVAC IR power control (#740)

5.5.2 20170808

• Extent max number of WS2812 pixels from 256 to 512 (#667)
• Add OTA handling if server responds with no update available (#695)
• Removed undocumented command FlashMode (#696)
• Fix compile time error message due to increased message buffer size (#703)

5.5.1 20170805

• Fix Sonoff Rf Bridge issues
• Add Sonoff RF Bridge MQTT messages on received and learned RF signal
• Add command VoltRes 0|1 to select voltage resolution to 0.1 V (#654)
• Add averaging to Analog input (#686)
• Add Energy tele data on Sonoff Pow Threshold change (#688)
• Fix inconsistent property names in Messages (#690)

5.5.0 20170730

• Reduce code space by removing the following commands as they are replaced by SetOption alternatives:
• SaveState = SetOption0
• ButtonRestrict = SetOption1
• Units = SetOption2
• MQTT = SetOption3
• MQTTResponse = SetOption4
• TempUnit = SetOption8
• Smoothing WS2812 animation poll, invert fade speed and max allowed wakeup time down to 3000 seconds
• Fix initial button press detection
• Add support for Sonoff RF Bridge 433 using command RfKey
• Fix regression from 5.0.7 by increasing message buffer size from 360 to 368 to accommodate 4 x DS18x20 sensors (#637)
• Add GroupTopic to Topic test when using ButtonTopic/SwitchTopic to send either ON/OFF or TOGGLE (#642)
• Adjust HLW calibration limits to accommodate HuaFan device and add commands HlwPSet, HlwUSet and HlwISet (#654)

5.4.0 20170725

• Fix command reset regression introduced in 5.2.0
• Increase polling from 0.1 second to 0.05 second
• Add multipress to all buttons
• Fix button 1 double press behaviour on multi relay devices
• Add support for Hua Fan Smart Socket (#479)
• Add support for Sonoff 4ch Pro (#565)
• Add command SetOption13 1 to allow immediate action on single button press
• (disables multipress, hold and unrestricted commands) (#587)

5.3.0 20170715

• Major Hue rewrite which might introduce Alexa problems. If so, initiate an issue
• Add support for Sonoff Led and BN-SZ01 Ceiling Led brightness control to Hue
• Fix Sonoff Led Power, Dimmer and Color MQTT response (#176)
• Add commands Delay and Backlog to allow multiple commands at once separated by ";" (#593)
• Use default flashmode DOUT to solve restart hangs on esp8285 chips (#453, #598)
• Change Web console column width from 99 to 300 (#599)

5.2.4 20170703

• Removed flash mode update after selecting different module solving esp8285 related problems
• Add device type flag to sonoff_template.ino
• Change Sonoff Led Wakeup and add support for Sonoff BN-SZ01 Led (#567)

5.2.3 20170630

• Change Sonoff Led color conversion code
• Fix SetOption12 handling
• Simplify auto configuration upgrade
• Add option Upgrade <version_number> to only upgrade to any higher version (Old PR #213)
• Change FallbackTopic to cmnd/<MQTTClient>/<command> <parameter> bypassing FullTopic and Prefix (#538)

5.2.2 20170625

• Add configuration SaveAddress to Status 1 and Information Page
• Change Sonoff Led Color conversion from AtoH to strtol
• Fix possible wrong uploads due to configuration overwrites (#542)
• Fix payload negative numbers (#547)

5.2.1 20170622

• Fix Restore Configuration in case of lower version
• Revert auto configuration upgrade allowing easy upgrade which was removed in version 5.2.0
• Fix config auto upgrade from versions below version 4.1.1 (#530)

5.2.0 20170619

• Add command SetOption12 1 to disable newly released configuration flash rotate to reduce flash wear
• Fix command CounterDebounce by removing test for active GPIO (#524)
• Add command SetOption33 1..250 to allow user configure POW Max_Power_Retry count (#525)

5.1.7 20170616

• Prep removal of SetOptions alternatives
• Restore webpage upgrade error messages removed in 5.1.5
• Add hold button functionality to buttons 2 to 4
• Add command SetOption32 1..100 to set Key Hold Time from 0.1 seconds to 10 seconds (#200)
• Allow slashes in Topic, GroupTopic, ButtonTopic and SwitchTopic (#507)
• Changed webpage form actions from post to get and use relative path url (#434, #522)

5.1.6 20170606

• Shrink code
• Removed online configuration of Domoticz In and Domoticz Out MQTT strings
• Removed commands DomoticzInTopic and DomoticzOutTopic
• Add define KEY_HOLD_TIME to configure button hold threshold before sending MQTT Hold message
• Add command StateText4 to configure button MQTT Hold text (= MQTT_CMND_HOLD)
• Add command SetOption11 0|1 to swap pushbutton single and double press functionality (#200)
• Add command SwitchMode 5 (PUSHBUTTONHOLD) and 6 (PUSHBUTTONHOLD_INV) (#489)

5.1.5 20170604

• Shrink code in preparation to ESP8266-Arduino 2.4.0-rc1
• Add effect parameter to HUE Device (#464)

5.1.4 20170601

• Removed pre-compiled versions from repository as they are available within the release
• Changed HUE Device type to color supporting version (#464)
• Fix compile error when BE_MINIMAL is selected (#467, #476)
• Add multiple compiled versions to release using updated Travis script and platformio.ini (#467)

5.1.3 20170520

• Add Domoticz Counter

5.1.2 20170519

• Fix Counter/Timer JSON message and update Counter/Timer on webpage
• Fix WS2812 Domoticz related regression issues

5.1.1 20170517

• Allow command FullTopic in group mode
• Prepare for more use of RTC memory
• Add independant WS2812 led string power control (#386, #390)
• Add command Counter to control up to four GPIO falling edge interrupt counters or timers (#459)
• Add command CounterType to select between pulse counting or pulse timing
• Add command CounterDebounce to select global counter debounce time in mSec

5.1.0 20170513

• Fix Offline/Removal of retained topic when FullTopic is changed
• Add FullTopic to MQTT Configuration and Information web pages
• Add license model GPLv3 (#188)

5.0.7 20170511

• Fix possible exception 28 on empty command
• Add command SetOption0 as replacement for SaveState
• Add command SetOption1 as replacement for ButtonRestrict
• Add command SetOption2 as replacement for Units
• Add command SetOption4 as replacement for MqttResponse
• Add command SetOption8 as replacement for TempUnit
• Add command SetOption10 On|Off to select between Offline or Removing previous retained topic (#417, #436)

5.0.6 20170510

• Remove hyphen in case of a single DHT sensor connected (#427)
• Add command MqttRetry to change default MQTT reconnect retry timer from minimal 10 seconds (#429)

5.0.5 20170508

• Add command FullTopic with tokens %topic% (replaced by command Topic value) and
• %prefix% (replaced by command Prefix values) for more flexible topic definitions (#244)
• See wiki > MQTT Features https://github.com/arendst/Tasmota/wiki/MQTT-Features for more information

5.0.4 20170505

• Add Sonoff Pow Energy Total up to 40 MWh
• Add command EnergyReset 1|2|3 to reset Energy counters (#406)
• Fix Domoticz Energy logging (#411)
• Add command PowerOnState 4 to keep relay always on and disabling all power control (#418)

5.0.3 20170504

• Add command SensorRetain on|off to enable retaining of mqtt message tele/sonoff/SENSOR (#74)
• Change WifiConfig timeout from 60 seconds to 180 seconds (#212)
• Change Sonoff Touch command Ledstate functionality by turning led on if power is off (#214)
• Add 4 seconds delay after power on before enabling button to workaround Wemos D1 mini RTS circuit (#380)

5.0.2 20170503

• Reset SaveData, SaveState and MqttResponse to default values due to rearranging settings
• Moved some settings to flag area
• Add command TempUnit Celsius|Fahrenheit for selecting Celsius or Fahrenheit (#347)
• Add command TempRes 0..3 for selecting Temperature Resolution (#347)
• Add command HumRes 0..3 for selecting Humidity Resolution (#347)
• Add command PressRes 0..3 for selecting Pressure Resolution (#347)
• Add command EnergyRes 0..5 for selecting Energy Resolution (#347)
• Add "TempUnit":"C|F" to sensor JSON output (#347)
• Add support for up to three DHT type sensors each using a different GPIO (#339, #404)

5.0.1 20170429

• Adjust Sonoff SC messages to prepare for display feature
• Move static data from RAM to Flash
• Fix PowerOnState for some devices not reporting "Power on" state (#284, #380, #383)

5.0.0 20170425

• Memory status message update
• Fix setting migration to better preserve settings during move (#382)
• Best practice is first doing a Backup Configuration before installing version 5.0.0
• Reset save count after setting move
• Start using new linker script without SPIFFS

4.2.0 20170424

• Prepare for SPIFFS removal by moving settings to EEPROM area
• Fix compilation error when webserver is disabled (#378)

4.1.3 20170410

• Add user configurable GPIO to module S20 Socket and Slampher
• Add support for Sonoff SC (#112)
• Set PWM frequency from 1000Hz to 910Hz as used on iTead Sonoff Led firmware (#122)
• Set Sonoff Led unconfigured floating outputs to 0 to reduce exceptions due to power supply instabilities (#122)
• Add Access Point Mac Address to Status 11 and Telemetry (#329)
• Fix DS18B20 negative temperature readings (#334)

4.1.2 20170403

• Rename Unrecognised command to Unknown command
• Remove all command lists
• Remove command SmartConfig (superseded by WifiConfig)
• Fix boot loop when selecting module Sonoff 4CH or Sonoff Touch on non ESP8285 hardware
• Add optional support for Toshiba and Mitsubishi HVAC IR control (needs updated IRremote8266 library) (#83, #257)
• Add all configured switches to Domoticz Configuration web page (#305)
• Fix compile error when selecting WS2812 DMA (#313)

4.1.1 20170329

• Fix default Telemetry for command Prefix3
• Fix webserver Module parameters for disabled select
• Fix sensor status for enabled switches
• Remove Light as alternative for Power (save code space)
• Remove migration option from pre V3 (code cleanup)
• Remove unofficial SPIFFS support (code cleanup)
• Remove command list when unknown command is entered (save code space)
• Rename Status11 json from StatusPWR to unique StatusSTS
• Rename command Gateway to IPAddres2, Subnetmask to IPAddress3 and DnsServer to IPAddress4 (save code space)
• Add Command MqttResponse to select either command or RESULT topic as response (#258)
• Add command StateText1 to StateText3 to assign MQTT_STATUS_OFF, MQTT_STATUS_ON and MQTT_CMND_TOGGLE respectively (#286)
• Remove restart after IPAddress changes (#292)
• Add support for MAX31850 in xsns_ds18x20.ino (#295)
• Fix possible uptime update misses (#302)

4.1.0 20170325

• Change static IP addresses in user_config.h from list (using commas) to string (using dots)
• Unify display result of commands Modules, Module and Gpios
• Rewrite Module selection web page to bring size down from 18651 to 4319 bytes (!) (#234, #240)
• Add basic support for (Lixada) H801 RGBWW controller (#252)
• Add command Prefix1 to Prefix3 to assign SUB_PREFIX, PUB_PREFIX and PUB_PREFIX2 respectively (#255)
• Add static ip addresses to flash (#262)
• Add commands IpAddress, Gateway, Subnetmask and DnsServer to select static ip addresses (#273)

4.0.8 20170321

• Fix entering non-numeric webpassword
• Force selection between TLS or Webserver due to memory restraint (#240)
• Allow entering empty string using "0" for selected commands (#242)
• Fix exception when posting commands to web console containing % (#250)

4.0.7 20170319

• Increased Sonoff Led PWM frequency from 432 to 1000
• Fix possible watch dog reboot after changing module type on web page
• Fix reporting of GPIO usage from web page
• Fix Sonoff Led blank during firmware upgrade
• Fix Sonoff Led flicker and possible flash corruption by using latest Arduino-esp8266 versions of pwm core files included in sonoff library (#211)
• Add PWM output control with commands PWM1 to PWM5 using user selectable GPIOs (#211)
• Fix exceptions due to low values of commands HlwPCal (10000), HlwUCal (1000) and HlwICal (2500) (#223)
• Add Switch state to sensor status (#227, #233)
• Add user configurable GPIO to module Sonoff Touch (#228)
• Add define WEB_PORT to user_config.h to change default web server port from 80 (#232)
• Fix failed Ota Firmware upgrade started from Web page (#235)

4.0.6 20170316

• Fix to better find device by Wifi hostname
• Fix compile error when some I2C devices are disabled
• Add (experimental) support for SHT1X emulating I2C (#97)
• Add ADC to ElectroDragon (#203)
• Add support for Sonoff Dev (#206)

4.0.5 20170314

• Add command Status 11 to show power status with Vcc if define USE_ADC_VCC is enabled (default)
• Add ADC input to Sonoff SV and Wemos D1 mini - Needs recompile with define USE_ADC_VCC disabled (#137)
• Add MQTT host:port to timeout message (#199)

4.0.4 20170312

• Add pulse timers for up to 4 relays (#106)
• Fix Sonoff Led power state when dimmer or color is 0 (#176)
• Add command NtpServer to configure up to three NTP servers (#177)
• Delete module User Test as module Wemos D1 mini has same/more user configurable GPIO (#178)
• Add more user configurable GPIO to module ElectroDragon (#183)

4.0.3 20170309

• Renamed Module NodeMCU to WeMos D1 mini
• Add GPIO1 as user option to some modules
• Add Buttons, Relays and Leds to user configurable options (#159)
• Add description on Module parameters web page to some well known GPIOs (#107, #171)

4.0.2 20170308

• Restore correct seriallog level after Serial logging was disabled
• Add simple dimmer slider to Sonoff Led web page
• Reduced root webpage size by 31%
• Expand Status 2 with Build date/time and core version
• Fix webserver redirection when not in WifiManager mode (#156)
• Add command ButtonRestrict On/Off to restrict access to button hold and button multi press options above 2 (#161)
• Fix DS18S20 negative temperature readings (#165)
• Fix crlf compilation error due to bad syntax (#144, #167)

4.0.1 20170305

• Fix char default sizes and set MESSZ to 360 (#143)
• Fix SerialLog setting status
• Disable syslog when emulation is active
• Add DS18B20 web page display refresh

4.0.0 20170303

• Add define to remove config migration code for versions below 3.0 (See Wiki-Upgrade-Migration path)
• Free memory by switching from String to char[]
• Raised Sonoff Led PWM frequency from 200Hz to 432Hz in search of stability (hardware watchdog timeouts) (#122)
• Increase message size and suggested minimum MQTT_MAX_PACKET_SIZE to 512 (#114, #124)
• Remove runtime warning message regarding MQTT_MAX_PACKET_SIZE too small as it is now moved to compile time (#124)
• Fix possible panics with web console and http commands while UDP syslog is active (#127)
• Add optional static IP address (#129)
• Add define ENERGY_RESOLUTION in user_config.h to allow user control over precision (#136)

3.9.22 20170228

• Update web console
• Fix Status 4 JSON message
• Add Exception info during restart if available
• Add osWatch service to detect loop hangs that might happen during (OTA) upgrades
• Add WiOn support for relay and switch only (#82, #102)
• Allow for user specified relay count up to four in sonoff_template.h (#109)
• Add support for HTU21 compatible I2C sensors SI7013, SI7020 and SI7021 (#118)
• Add NodeMCU or Wemos configuration option (#119)

3.9.21 20170224

• Add ajax to web root page and web console (#79)
• Add commands SwitchMode1..4 and enable user switches 2, 3 and 4 (#84, #88)
• Fix MQTT upgrade when webserver is active

3.9.20 20170221

• Add minimal basic authentication to Web Admin mode (#87)
• Fix Hue and add HSB support (#89)

3.9.19 20170219

• Sonoff Led: Made GPIO04, 05 and 15 available for user
• Sonoff Led: Add commands Fade, Speed, WakupDuration, Wakeup and LedTable

3.9.18 20170218

• Fix ledstate 0 to turn off led
• Fix Sonoff Led dimmer range (#16)
• Change Sonoff Led command Dimmer to act on both cold and warm color
• Add Sonoff Led command Color CCWW where CCWW are hexadecimal values fro 00 - FF
• Reduce Sonoff Led flickering by disabling interrupts during flash save and disabling
• Led during OTA upgrade and Web upload (#16)

3.9.17 20170217

• Fix possible ArduinoJSON related memory fragmentation
• Changed console logging using less memory
• Add GPIO04 as user selectable for Sonoff Dual (#75)

3.9.16 20170214

• Update latching relay handler
• Add support for IR led using IRremoteESP8266 library (#59)
• Add Hue argument passing using ArduinoJSON library (#59)

3.9.15 20170213

• Change JSON float values from string to number according to http://json.org (#56)
• Add support for exs latched relay module https://ex-store.de/ESP8266-WiFi-Relay-V31 (#58)
• Add support for inverted relays
• Changed MAX_LOG_LINES from 70 to 60 to preserve memory

3.9.14 20170211

• Add False and True as alternatives for 0/Off and 1/On (#49)
• Fix Status10 JSON format (#52)
• Fix DS18x20 using OneWire library (#53)

3.9.13 20170210

• Add FlashChipMode to Status 4
• Removed redundant DHT2 option and code
• Add Sonoff SV GPIO pin 05 configuration (#40)
• Add configuration file backup and restore via web page
• Fix latency due to light_sleep mode even if sleep was set to zero (#50)

3.9.12 20170208

• Fix compile error when webserver is disabled (#30)
• Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during OTA upload
• Fix hostname issues by not allowing user entry of string formatting and removing from user_config.h (#36)

3.9.11 20170204

• Fix command I2Cscan
• Fix not allowed spaces in Topic, ButtonTopic and SwitchTopic
• Make all TELEMETRY, STATUS and COMMAND message topics unique (#4)
• Advertise command topic to be used by iobroker (#299)
• Fix butten (non)detection if no GPIO_KEY1 is defined (#13)
• Change WeMo serialnumber from 7 decimal chars to 8 hexadecimal chars (#18)
• Update web page with Build Date/Time, Emulation and mDNS Discovery and Advertise information (#21)

3.9.10 20170130

• Add WS2812 Color Type selection (RGB or GRB) to user_config.h (#7)
• Hue api changes to support HUE App(s) (#8)

3.9.9 20170130

• Add command status 10 showing sensor data
• Fix hlw status messages if hlw is disabled

3.9.8 20170130

• Remove GPIO07 and GPIO08 from user selectable (#5)

3.9.7 20170129

• Fix possible WS2812 exceptions when using emulation
• Add command Emulation to dynamic configure Belkin WeMo and Hue Bridge for Alexa

3.9.6 20170129

• Add dynamic sleep for WS2812 animation (#1)

3.9.5 20170128

• Fix error message in case of wrong Domoticz command

3.9.4 20170127

• Fix Sonoff Dual Relay switching (#287)

3.9.3 20170127

• Add confirmation before Restart via webpage
• Expand Domoticz Configuration webpage with Key, Switch and Sensor Index and
• add commands DomoticzSwitchIdx and DomoticzSensorIdx (#86) (#174) (#219)
• Fix default DHT11 sensor driver selection
• Fix LedPower status after button press (#279)
• Add command Sleep 0 - 250 mSec for optional light sleep mode to lower energy consumption (#272)
• (Expect overall button/key/switch misses and wrong values on Sonoff Pow)
• Add Hue brightness extension (#281)
• Fix Hue brightness and change to call by reference (#283)

3.9.2 20170124

• Add confirmation before Reset Configuration via webpage (#244)
• Add WS2812 features (see Wiki commands)

3.9.1 20170124

• Change PowerOnState function to only trigger when Power On (and not just restart) (#238)
• Move HLW interrupts back to RAM and make WS2812_DMA optional as it generates Exception on Pow (#264)
• Add charset=utf-8 to webpages (#266)
• Update Hue emulation (#268)
• Fix status module number
• Add support for domoticz Dimmer on Sonoff_Led and WS2812
• Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during web upload

3.2.6a 20170120

• Fix Sonoff Pow compile error (#255)
• Move HLW interrupts back to ROM (Needed for WS2812 DMA interrupts)
• Removed all IO config from user_config.h as this will be done by commands or webpage
• Removed MessageFormat and supports JSON only except POWER/LIGHT status
• Add command LedPower to control main led (#247)
• Add more FriendlyNames for Hue (#254)
• Add DMA support for WS2812 when using pin 3 while other pins work just as well in my case...
• Add HUE emulation for Alexa (#229)
• Add basic WS2812 support (#229)
• Fix Wemo when MQTT is disabled (#245)
• Revert ButtonTopic and change SwitchTopic1 - 4 to one SwitchTopic
• Rename MqttUnits to Units
• Add Mqtt command to enable/disable MQTT

3.2.2a 20170115

• Add dynamic (Sonoff) Module, user GPIO and sensor selection (one size fits (almost) all)
• Add support for Sonoff LED
• Add Seriallog disable after 600 seconds for Sonoff Dual and 4 Channel
• Add ButtonTopic2 - 4, SwitchTopic1 - 4 and SwitchRetain

3.2.2 20170113

• Fix PowerOnState 2 functionality after re-applying power (#230)

3.2.1 20170113

• Fix some failed command decoding (#228)
• Removed passwords from status messages (#216)

3.2.0 20170111

• Add I2C BH1750 sensor (#222)
• Sensor rewrite preparing for online selection

3.1.16 20170109

• Fix Domoticz possible error condition
• Remove Wifi password from connection message (#216)
• Add Configure Other menu item to web page (#209)
• Add command FriendlyName, field Friendly Name and define FRIENDLY_NAME to be used by Alexa
• eliminating current use of MQTT_CLIENT_ID (#209)
• Add friendlyname to webpage replacing former hostname

3.1.15 20170108

• Fix Domoticz send key regression with Toggle command

3.1.14 20170107

• Add support for command TOGGLE (define MQTT_CMND_TOGGLE) when ButtonTopic is in use and not equal to Topic (#207)

3.1.13 20170107

• Fix web console command input when SUB_PREFIX contains '/' (#152)
• Add command response to web command (#200)
• Add option to disable MQTT as define USE_MQTT in user_config.h (#200)

3.1.12 20170106

• Add OTA retry to solve possible HTTP transient errors (#204)
• Fix MQTT host discovery

3.1.11 20170105

• Add mDNS to advertise webserver as .local/

3.1.10 20170105

• Fix ButtonTopic when SUB_PREFIX = PUB_PREFIX
• Add workaround for possible MQTT queueing when SUB_PREFIX = PUB_PREFIX
• Add optional MQTT host discovery using define USE_DISCOVERY in user_config.h (#115)

3.1.9 20170104

• Fix Power Blink start position (toggled)
• Change PulseTime increments: 1 .. 111 in 0.1 sec (max 11 seconds) and 112 .. 64900 in seconds (= 12 seconds until 18 hours) (#188)
• Add support for SUB_PREFIX = PUB_PREFIX (#190)

3.1.8 20170103

• Add retain flag to LWT offline and only send "tele/sonoff/LWT Offline" (#179)
• Change retained LWT Online message to only send "tele/sonoff/LWT Online"

3.1.7 20161231

• Add retained message LWT Online when sonoff makes MQTT connection (#179)

3.1.6 20161230

• Add blinking using commands BlinkTime, BlinkCount and Power Blink|3|BlinkOff|4 (#165)

3.1.5 20161228

• Fix serial space command exception (28)

3.1.4 20161227

• Fix MQTT subscribe regression exception (3) (#162)
• Fix serial empty command exception (28)

3.1.3 20161225

• Extent Domoticz configuration webpage with optional indices (#153)
• Fix multi relay legacy tele message from tele/sonoff/2/POWER to tele/sonoff/POWER2
• Add support for iTead Motor Clockwise/Anticlockwise

3.1.2 20161224

• Extent command PowerOnState with toggle at power on (option 2 is now option 3!) (#156)

3.1.1 20161223

• Add support for Sonoff Touch and Sonoff 4CH (#40)
• Update DomoticzIdx and DomoticzKeyIdx with relay/key index (DomoticzIdx1/DomoticzKeyIdx1)
• Add command PowerOnState to control relay(s) at power on (#154)

3.1.0 20161221

• Add Sonoff Pow measurement smoothing
• Fix serial command topic preamble error (#151)
• Fix 2.x to 3.x migration inconsistencies (#146)

3.0.9 20161218

• Add Sonoff Pow voltage reading when relay is on but no load present (#123)

3.0.8 20161218

• Add temperature conversion to Fahrenheit as option in user_config.h (TEMP_CONVERSION) (#145)

3.0.7 20161217

• Add user_config_override.h to be used by user to override some defaults in user_config.h (#58)
• Fix Sonoff Pow low power (down to 4W) intermittent measurements (#123)

3.0.6 20161217

• Fix MQTT_CLIENT_ID starting with % sign as in "%06X" (#142)
• Add auto power off after PulseTime### 0.1 Sec to relay 1 (#134)

3.0.5 20161215

• Add more control over LED with command LedState options (#136, #143)
• LED_OFF (0), LED_POWER (1), LED_MQTTSUB (2), LED_POWER_MQTTSUB (3), LED_MQTTPUB (4), LED_POWER_MQTTPUB (5), LED_MQTT (6), LED_POWER_MQTT (7)
• Add option WIFI_RETRY (4) to command WifiConfig to allow connection retry to other AP without restart (#73)

3.0.4 20161211

• Fix intermittent Domoticz update misses (#133)

3.0.3 20161210

• Fix compiler warnings (#132)
• Remove redundant code
• Fix Domoticz pushbutton support

3.0.2 20161209

• Add pushbutton to SwitchMode (#130)

3.0.1 20161209

• Fix initial config

3.0.0 20161208

• Migrate and clean-up flash layout
• Settings from version 2.x are saved but settings from version 3.x can not be used with version 2.x
• Change SEND_TELEMETRY_RSSI to SEND_TELEMETRY_WIFI and add AP and SSID to telemetry
• Split long JSON messages
• Fix inconsistent status messages
• Fix all status messages to return JSON if enabled
• Remove relay index in cmnd/sonoff//POWER now changed
• to cmnd/sonoff/POWER for single relay units
• and cmnd/sonoff/POWER for multi relay units like Sonoff dual
• Add retain option to Power/Light status controlled by command PowerRetain On|Off (#126)

2.1.2 20161204

• Add support for second wifi AP (#73)
• Update command WifiConfig
• Fix possible WifiManager hang

2.1.1a 20161203

• Fix scan for wifi networks if WeMo is enabled
• Fix syslog setting using web page

2.1.1 20161202

• Add support for ElectroDragon second relay and button (only toggle with optional ButtonTopic) (#110)

2.1.0 20161202

• Add optional EXPERIMENTAL TLS to MQTT (#49)
• Fix MQTT payload handling (#111)
• Optimized WeMo code

2.0.21a 20161201

• Fix WeMo PowerPlug emulation

2.0.21 20161130

• Add Belkin WeMo PowerPlug emulation enabled with USE_WEMO_EMULATION in user_config.h (Heiko Krupp) (#105, #109)

2.0.20 20161130

• Relax MQTTClient naming but only allows hexadecimal uppercase numbers (#107)
• Add I2C support with command I2CScan
• Add I2C sensor driver for HTU21 as alternate sensor using TH10/16 connectors (Heiko Krupp) (#105)
• Add I2C sensor driver for BMP085/BMP180/BMP280/BME280 as alternate sensor using TH10/16 connectors

2.0.19a 20161127

• Add support for ButtonTopic and ButtonRetain to wall switch function
• Add pullup to SWITCH_PIN and command SwitchMode to syntax

2.0.18 20161126

• Add SUB_PREFIX multi level support allowing 'cmnd' or 'cmnd/level2/level3'
• Add wall switch function to GPIO14 and command SwitchMode (Alex Scott) (#103)

2.0.17 20161123

• Calibrate HLWPCAL from 12345 to 12530
• Add alternative sensor driver DHT2 using Adafruit DHT library
• Add define MESSAGE_FORMAT to user_config.h
• Throttle console messages
• Shorten JSON messages
• Fix possible Panic
• Fix User mode webserver security

2.0.16 20161118

• Add alternative sensor driver DS18x20 using OneWire library (#95)
• Change sensor MQTT message from tele/sonoff/TEMPERATURE to tele/sonoff/DHT/TEMPERATURE or
• tele/sonoff/DS18B20/TEMPERATURE or tele/sonoff/DS18x20/1/TEMPERATURE
• Add sensors to root webpage and auto refresh every 4 seconds (#92)
• Add optional JSON messageformat to all telemetry data
• Enforce minimum TelePeriod to be 10 seconds
• Fix Energy Yesterday reset after restart
• Add Energy Today restore after controlled restart

2.0.15 20161116

• Change TODAY_POWER and PERIOD_POWER to TODAY_ENERGY and PERIOD_ENERGY
• Fix serial regression
• Fix syslog hangs when loghost is unavailable

2.0.14 20161115

• Add HLW threshold delay
• Fix HLW intermittent current deviation
• Fix button functionality during wificonfig
• Add CRC check to DS18B20 sensor (#88)

2.0.13 20161113

• Add additional upload error code descriptions
• Add PlatformIO support (#80)

2.0.12 20161113

• Fix Serial and Web response regression when no MQTT connection available
• Fix Sonoff Dual power telemetric data for second relay
• Removed MQTT password from Information web page
• Hide MQTT password from Configure MQTT web page

2.0.11 20161111

• Rewrite button and web toggle code
• Fix NTP sync
• Add HLW calibration commands HLWPCAL, HLWUCAL and HLWICAL (need define USE_POWERCALIBRATION)
• Fix power threshold tests

2.0.10 20161109

• Add additional Domoticz define (#63)
• Add defines MQTT_STATUS_ON and MQTT_STATUS_OFF in user_config.h to select status On/Off string
• Fix status response differences (#65)
• Fix divide by zero exception (#70)
• Fix syslog loop exception

2.0.9 20161108

• clarify MODULE in user_config.h
• Fix hlw false values

2.0.8 20161108

• Add initial status after power on
• Separate driver files
• Fix hlw code and calibrate Pow
• Move user config defines to user_config.h (#61)

2.0.7 20161030

• Make Ticker mandatory
• Add Domoticz support (Increase MQTT_MAX_PACKET_SIZE to 400) (#54)
• Add command MessageFormat 0|1 to select either legacy or JSON output

2.0.6 20161024

• Add Sonoff Pow power factor
• Initial support for up to four relays using iTEAD PSB (4Channel)
• • Currently only supports one button (All buttons behave the same)
• • Use command MODEL 4 to select four relay option

• (After first power on it will support 2 relays like Sonoff Dual)
  

• Fix ledstate
• Add command Status 9 to display Sonoff Pow thresholds
• Add commands PowerLow, PowerHigh, VoltageLow, VoltageHigh, CurrentLow and CurrentHigh for use
• with Sonoff Pow thresholds

2.0.5 20161018

• Add updates to user_config.h - moved SEND_TELEMETRY_DS18B20 and SEND_TELEMETRY_DHT to module area.
• As Sonoff TH10/16 does not have the logic installed for GPIO04 You'll have to select ONE of both
• Add Sonoff Pow support (experimental until Pow tested)
• Add command Status 8 to display Sonoff Pow energy values
• Add command MqttUnits On|Off to add units to values
• Change web main page header character size
• Change On/Off to ON/OFF status messages to satisfy openHAB
• Change TEMP to TEMPERATURE and HUM to HUMIDITY

2.0.4 20161009

• Add MQTT_BUTTON_RETAIN, SAVE_DATA and SAVE_STATE defines to user_config.h (#35)
• Update ButtonRetain to remove retained message(s) from broker when turned off
• Add Retain for second relay on Sonoff Dual
• Provide power status messages with device topic index if requested

2.0.3 20161008

• Update wifi initialization
• Add command BUTTONRETAIN for optional MQTT retain on button press (#35)
• Add command SAVESTATE to disable power state save. May be used with MQTT retain

2.0.2 20161006

• Fix wifi issue 2186

2.0.1 20161002

• Fix button press

2.0.0 20161002

• Update Sonoff TH10/16 sensor pins (My TH10 only has GPIO14 connected)
• Add full support for Sonoff dual

1.0.35 20160929

• Add more lines to console
• Add timeout and disable MQTT on web upload
• Add command SAVEDATA to control parameter save (for flash wear aficionados) (#30)

1.0.34 20160926

• Fix button press six and seven
• Add more information to webserver

1.0.33 20160915

• Better WPS error message
• Separate webserver code from support.ino into webserver.ino
• Fix webserver User by removing unwanted restart option

1.0.32 20160913

• Add Wifi Protected Setup (WPS) as third option for initial config
• Add command WIFICONFIG replacing deprecated command SMARTCONFIG
• Add option WIFICONFIG 3 to start WPSconfig
• Add option WIFICONFIG 0 to start saved Wifi config tool (WPSconfig, Smartconfig or Wifimanager)
• Change button behaviour - See Wiki

1.0.31 20160907

• Fix DS18B20 misread if teleperiod = 2
• Tuned sensor code
• Updated preferred ElectroDragon connection to Relay 1 and Button 1
• Moved SONOFF and ELECTRO_DRAGON port config to user_config.h

1.0.30 20160902

• Fix command TELEPERIOD 0
• Add ESP- tag to UDP log message for easy rsyslogd filtering
• Add ElectroDragon (Relay 2 only) functionality. Select with #define MODULE ELECTRO_DRAGON
• Add ? as null message alternative
• Add DHT temperature and humidity telemetry support. Enable with #define SEND_TELEMETRY_DHT
• Add DS18B20 temperature telemetry support. Enable with #define SEND_TELEMETRY_DS18B20
• Restrict HOSTNAME, MQTTCLIENT, TOPIC and BUTTONTOPIC in topic mode only

1.0.29 20160831

• Allow UPGRADE, OTAURL, RESTART, RESET, MQTTHOST, MQTTPORT, MQTTUSER, MQTTPASSWORD and WEBSERVER also in group mode

1.0.28 20160831

• Add webserver state to status 5
• Add optional PUB_PREFIX2 (tele) for telemetry usage
• Add command TELEPERIOD
• Fix syntax message
• Change memory status display

1.0.27 20160831

• Add sketch flash size
• Add console to webserver
• Add command weblog
• Change WifiManager web pages to minimal
• Change display default hostname and MQTT client id in webserver
• Change HTTP command interface to http://sonoff-1234/cm?cmnd=light 2
• Change HEARTBEAT to UPTIME

1.0.26 20160829

• Add define USE_WEBSERVER to disable web server code in source
• Add file upload as alternative for ota upload to webserver
• Add information to webserver
• Add command hostname
• Add command logport
• Change HTTP command interface to http://sonoff-1234/cmd?cmnd=light 2
• Change button behaviour with regards to Smartconfig and OTA upload. See README.md
• Enforce default hostname to either "%s-%04d" or user defined without any %
• Enforce default mqtt client id to either "DVES_%06X" or user defined without any %

1.0.25 20160822

• Remove config system halts to keep ota available

1.0.24 20160821

• Add test for MQTT_SUBTOPIC
• Change log range to LOG_LEVEL_ALL
• Change MQTT introduction messages
• Moved MQTT_MAX_PACKET_SIZE warning message to introduction messages

1.0.23 20160821

• Add option USE_SPIFFS to move config from flash to spiffs
• Add webserver with options 0 (off), 1 (user) and 2 (admin)
• Add HTTP command interface (http://sonoff-1234/c?cmnd=light 2)
• Add wifimanager countdown counter
• Add command line webpage
• Add relay control to wifimanager
• Add restart option 99 to force restart
• Fix wifi hostname
• Fix NETBIOS hostname problem by reducing default hostname length
• Fix possible exception if WIFI_HOSTNAME is changed
• Fix upgrade messages
• Reduce memory use by redesigning config routines
• Split syntax message
• Rename define SERIAL_IO to USE_SERIAL

1.0.22 20160814

• Add all MQTT parameters for configuration
• Add wifimanager to configure Wifi and MQTT via web server
• Change NTP time handling
• Fix Smartconfig parameter buffer overflow
• Fix PlatformIO warnings

1.0.21 20160808

• Remove semaphore as subscription flooding (more than 15 subscriptions per second) is managed by SDK (LmacRxBlk:1)
• Add optional RTC interrupt (define USE_TICKER) to keep RTC synced during subscription flooding
• Remove heartbeatflag

1.0.20 20160805

• Add semaphore to handle out of memory when too many subscriptions requested
• Use Daylight Saving (DST) parameters from user_config.h when timezone = 99
• Add status 7 option displaying RTC information
• Add ledstate to status 0

1.0.19 20160803

• Fix possible MQTT_CLIENT_ID induced Exception(28)

1.0.18 20160803

• Moved Cfg_Default
• Fix negative data handling
• Remove MQTT information from status 1 and add labels to status 1
• Add mac address to status 5
• Add MQTT ClientId, UserId and Password to status 6

1.0.17 20160731

• Better variable range checking
• Change ambiguous connection messages
• Add timestamp to serial message

1.0.16 20160729

• Moved wifi, rtc, syslog and config to support.ino
• Fixed button action when buttontopic is used. Introduced with 1.0.15
• Better buffer overflow checks (strlcpy)

1.0.15 20160728

• Removed pubsubclient config changes from sonoff.ino as it doesn't work
• reapply MQTT_MAX_PACKET_SIZE 256 and MQTT_KEEPALIVE 120 to PubSubClient.h
• Add status 0 option displaying all status messages
• Change MQTT_MAX_PACKET_SIZE from 1024 to 256
• Add buffer overflow checks (snprintf and strncpy)
• Implemented common string sizes

1.0.14 20160722

• Separate user config from sonoff.ino to user_config.h (pucebaboon)
• Change defaults from sidnas2 to domus1
• Add MQTT status message as status 6 (pucebaboon)
• Add status type to message (pucebaboon)
• Add pubsubclient config changes to sonoff.ino (pucebaboon)

1.0.13 20160702

• Add Ledstate 1 option to show power state on led

1.0.12 20160529

• Allow disable of button topic using "0"

1.0.11 20160524

• Provide button response if MQTT connection lost

1.0.10 20160520

• Add optional button topic to assist external MQTT clients
• Change version notation
• Reset default values

1.0.9 20160503

• Add more blinks
• Add reset 2 option erasing flash
• Add status 5 option displaying network info
• Add syslog check for Wifi connection
• Resize MqttPublish log array
• Change Wifi smartconfig active from 100 to 60 seconds
• Update Wifi initialization

1.0.8 20160430

• Remove use of Wifi config data from SDK
• Add status 3 (syslog info) and status 4 (flash info)
• Add restart option to button (5 quick presses)

1.0.7 20160420

• Add UDP syslog support
• Change HOST command to MQTTHOST command
• Add commands SYSLOG, SERIALLOG and LOGHOST
• Change hostname to lower case to distinguish between open-sdk version
• Add support for ESP-12F used in my modified wkaku power socket switch
• Fix timezone command
• Add RTC month names for future use
• Modify button code
• Remove initialization errors by better use of MQTT loop

1.0.6 20160406

• Removed Wifi AP mode (#1)
• Add test for Arduino IDE version >= 1.6.8
• Fix RTC time sync code

1.0.5 20160310

• Initial public release
• Show debug info by selecting option from IDE Tools Debug port: Serial