mirror of https://github.com/arendst/Tasmota.git
64 lines
4.3 KiB
Markdown
64 lines
4.3 KiB
Markdown
# TASMESH
|
|
|
|
This driver provides the ability to move TASMOTA-devices out of the WLAN by using ESP-NOW to communicate bidirectional with an internal protocol.
|
|
|
|
Thus the workload for the WLAN-router is reduced and with the reduced overhead the local 2.4-GHz-band will be freed of some traffic. Power consumption of the nodes will be reduced significantly allowing better battery powered projects with TASMOTA.
|
|
Automatic payload encryption is applied using the WiFi-password1 as the key. A maximum of 32 bytes of this password is used for the ChaCha20Poly1305 authenticated encryption as the key.
|
|
|
|
As ACK/NACK messages seem to be not reliable on both ESP-platforms, the method "send-and-pray" is used.
|
|
|
|
|
|
## Working priciple
|
|
|
|
An ESP32 is needed as gateway/broker to connect the nodes (typically an ESP8266) to the WLAN. The ESP32 will receive the MQTT-topic of every node and subscribe to it as a proxy.
|
|
If a MQTT-message in the form of 'cmnd/node_topic/...' is received, the broker will automatically send this to the referring node via ESP-NOW.
|
|
The broker will automatically send time messages to all nodes.
|
|
|
|
The nodes will send their MQTT-messages back to the broker via ESP-NOW.
|
|
|
|
## Enabling the driver
|
|
|
|
Add ``#define USE_TASMESH`` to your file ``user_config_override.h`` before compilation.
|
|
|
|
## Commands
|
|
|
|
**WARNING: The MAC address used for ESP-NOW on the broker is the *Soft AP MAC*, not the WiFi MAC.**
|
|
|
|
*NOTE: The colons in the mac addresses of the commands are optional.*
|
|
|
|
``MeshBroker`` - starts the broker on the ESP32, printing out the MAC and used WiFi-channel to the log. Must be called after WiFi is initialized!! Example 'Rule1 on system#boot do meshbroker endon'
|
|
|
|
``MeshChannel 1..13`` - changes the WiFi-channel (on the node) to n (1-13) according to the channel of the (ESP32-)broker.
|
|
|
|
``MeshNode AA:BB:CC:DD:EE:FF`` - starts a node and connects the the broker with the given MAC-address, will automatically send MQTT-topic to the broker
|
|
|
|
``MeshPeer AA:BB:CC:DD:EE:FF`` - usable to add a known node to another node to be able to send data via the mesh to the broker, that may be out of reach
|
|
|
|
``MeshInterval 2..200`` - changes the interval between mesh messages default set to 50 ms
|
|
|
|
## Rules
|
|
|
|
Rules examples:
|
|
|
|
- The broker must be started after wifi is up!!
|
|
- To start as ESP32 as broker after wifi and mqtt connection, use</br>``rule1 on system#boot do meshbroker endon``
|
|
- The node may be started as soon as possible. Once started wifi and webserver are disabled by design.
|
|
- To start the node immediately use</br>``rule1 on system#init do meshnode FA:KE:AD:DR:ES:S1 endon``
|
|
- To use mesh in combination with deep sleep, you must set a rule to re-initialize the mesh on wake-up.
|
|
The mesh status and parameters are **NOT** (yet) saved to flash and the mesh is not restarted automatically.
|
|
- **WARNING**: In case of a system-wide power outage, nodes will be unable to reconnect until after the broker is ready!
|
|
If all devices power up at the same time, a broker starting after `system#boot` will likely not be ready until *after* a node attempting to join at `system#init`.
|
|
This will cause the node to fail to mesh and *no retrying is implemented at this time*.
|
|
To account for this, instead of (or in addition to) using a rule on the nodes, assign all nodes to a common group topic (`GroupTopic2 tasnodes`) and have the broker send a command on that topic after it is ready:</br>`rule2 on mesh#broker=1 do publish cmnd/tasnodes/meshnode FA:KE:AD:DR:ES:S1`
|
|
- Add a known peer (another node in the mesh) after the node has initialized</br>``rule3 on mesh#node=1 do meshpeer FA:KE:AD:DR:ES:S1 endon``
|
|
|
|
## Limitations
|
|
|
|
The following limitations apply:
|
|
- An ESP32 is only supported as a broker
|
|
- An ESP8266 is only supported as a node
|
|
- No command persistence is implemented so use rules to start a broker or a node after start up or deep sleep
|
|
- Although node send queues are implemented there is no node receive queue so MQTT commands send to the node need to be as small as possible limited to a maximum of around 160 characters including the topic
|
|
- Although broker receive queues are implemented there is no broker send queue so MQTT commands send to the node need to be as small as possible limited to a maximum of around 160 characters including the topic
|
|
- As there is no direct connection from the node to the MQTT broker it will signal the node as LWT Offline
|