mirror of https://github.com/arendst/Tasmota.git
86 lines
5.8 KiB
Markdown
86 lines
5.8 KiB
Markdown
## Sonoff-Tasmota template information
|
|
Sonoff-Tasmota uses Device or Module information to control peripherals connected to GPIOs. This information is stored in the ``sonoff_template.h`` file as a device specific template. The template contains information about what GPIO should be connected to what peripheral and what GPIO may be configured online using the ``GPIO`` command or GUI Configure Module menu. In addition a device may need specific coding to process the data from these peripherals. The module number as provided by the ``Modules`` command is used to select this coding.
|
|
|
|
Starting with version 6.4.1.16 Sonoff-Tasmota Modules can be extended by users online using a template. To provide easy processing by Sonoff-Tasmota a user template is written as JSON text and could look like this:
|
|
|
|
{"NAME":"UserModule1","GPIO":[17,148,29,149,7,255,255,255,138,255,139,255,255],"FLAG":0,"BASE":18}
|
|
|
|
The four properties with UPPERCASE property names have the following functionality:
|
|
|
|
Property name | Property value description
|
|
--------------|-------------------------------------------------------------------------------------------------------------------
|
|
NAME | Up to 14 characters for the Module name
|
|
GPIO | Up to 13 decimal numbers from 0 to 255 representing GPIO0 to GPIO5, GPIO09, GPIO10 and GPIO12 to GPIO16
|
|
FLAG | 8 bit mask flag register
|
|
BASE | Module number of a hard-coded device to be used when device specific functionality is needed
|
|
|
|
The above example, based on the Generic Module does not allow ADC0 input.
|
|
|
|
## GPIO functionality
|
|
The GPIO functionality numbers are the same is shown by command ``GPIOs``. In addition code 255 is added to select a GPIO as user configurable via the GUI Configure Module menu.
|
|
|
|
## FLAG functionality
|
|
The FLAG value is an 8-bit mask where each bit controls a features. Add FLAG values to set multiple bits.
|
|
|
|
FLAG | Mask | Feature description
|
|
-----|----------|------------------------------
|
|
1 | xxxxxxx1 | Allowing to use Analog0 (ADC0) as input if define USE_ADC_VCC in ``my_user_config.h`` is disabled
|
|
2 | xxxxxx1x | Enable GUI pull-up control message
|
|
4 | xxxxx1xx | Not used
|
|
8 | xxxx1xxx | Not used
|
|
16 | xxx1xxxx | Not used
|
|
32 | xx1xxxxx | Not used
|
|
64 | x1xxxxxx | Not used
|
|
128 | 1xxxxxxx | Not used
|
|
|
|
## BASE functionality
|
|
The following table lists hard-coded device specific functionality. Notice that not all device modules need special handling.
|
|
|
|
BASE | Module | Description
|
|
-----|----------------|----------------------------------------------
|
|
4 | Sonoff Dual | Process relay and button via hardware serial interface using GPIO01 and GPIO03. Change baudrate to 19200 bps. Process buttons as single press only
|
|
9 | Sonoff Touch | Invert ledstate 1 functionality
|
|
10 | Sonoff LED | Set light type to 2 PWM channels disregarding SetOption15. Fix device specific LED instabilities by disabling GPIO04, GPIO5 and GPIO14
|
|
12 | 4 Channel | See 4
|
|
13 | Motor C/AC | Force all relays ON at Power On and disable command ``PowerOnState``
|
|
15 | EXS Relay(s) | Enable pulse latching using even/odd numbered relay pairs
|
|
18 | Generic | Show Wemos specific pin information in GUI
|
|
19 | H801 | Change hardware UART Tx from GPIO01 to GPIO02
|
|
20 | Sonoff SC | Enable and Process data via hardware serial interface using GPIO01 and GPIO03. Change baudrate to 19200 bps
|
|
21 | Sonoff BN-SZ | Set light type to 1 PWM channel disregarding SetOption15
|
|
22 | Sonoff 4CH Pro | Button handling disregarding SetOption13 only allowing single press to enable RF learning while holding the button
|
|
24 | Sonoff Bridge | Enable and Process data via hardware serial interface using GPIO01 and GPIO03. Change baudrate to 19200 bps. Process 16 buttons in web GUI. Enable EFM8BB1 firmware upload
|
|
25 | Sonoff B1 | Set light type to RGBWC using MY92x1
|
|
26 | AiLight | Set light type to RGBW using MY92x1
|
|
27 | Sonoff T1 1CH | See 9
|
|
28 | Sonoff T1 2CH | See 9
|
|
29 | Sonoff T1 3CH | See 9
|
|
38 | Sonoff Dual R2 | Process buttons as single press only
|
|
43 | Sonoff iFan02 | Enable command ``Fanspeed``. Disable Interlock and PulseTime. Tune status information, MQTT data and GUI. Sync with microcontroller. Process Domoticz Fan state
|
|
47 | Xiaomi Philips | Process Color Temperature using PWM2 and Intensity using PWM1
|
|
53 | Tuya Dimmer | Enable and Process data via software or hardware serial interface using GPIO 148 and 149 or forced GPIO01 and GPIO03. Change baudrate to 9600 bps. Process all Buttons
|
|
55 | ARMTR Dimmer | Enable and Process data via software or hardware serial interface using GPIO 148 and 149. Change baudrate to 115200 bps.
|
|
57 | PS-16-DZ | Enable and Process data via software or hardware serial interface using GPIO 148 and 149. Change baudrate to 19200 bps.
|
|
61 | YTF IR Bridge | Disable serial interface to stop loopback
|
|
65 | Mi Desk Lamp | Process rotary and Button1 data specific to this device
|
|
|
|
## Usage
|
|
A user provided template can be stored in Sonoff-Tasmota using the ``Template`` command. It has the following options.
|
|
|
|
Command | Payload | Description
|
|
---------|----------|---------------------------------------
|
|
Template | | Show current user template
|
|
Template | 0 | Copy active module template to user template
|
|
Template | 1 .. 69 | Copy hard-coded module template to user template
|
|
|
|
The following command will store a complete template based on the Generic module
|
|
``Template {"NAME":"UserModule1","GPIO":[17,148,29,149,7,255,255,255,138,255,139,255,255],"FLAG":0,"BASE":18}``
|
|
|
|
The following command will update the name of a stored template
|
|
``Template {"NAME":"UserModule2"}``
|
|
|
|
The following command will update the flag of a stored template
|
|
``Template {"FLAG":1}``
|
|
|
|
The following command will update the base of a stored template to Generic
|
|
``Template {"BASE":0}`` |