8.0 KiB

Raw Blame History

RELEASE NOTES

Migration Information

See migration path for instructions how to migrate to a major version. Pay attention to the following version breaks due to dynamic settings updates:

Migrate to Sonoff-Tasmota 3.9.x
Migrate to Sonoff-Tasmota 4.x
Migrate to Sonoff-Tasmota 5.14
Migrate to Sonoff-Tasmota 6.x
Migrate to Tasmota 7.x

--- Major change in parameter storage layout ---

Migrate to Tasmota 8.1
Migrate to Tasmota 8.x

While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v8.1.0 Doris the Settings are re-allocated in such a way that fallback is only allowed and possible to release v7.2.0 Constance. Once at v7.2.0 you're on your own when downgrading even further.

Supported Core versions

This release will be supported from ESP8266/Arduino library Core version 2.6.3 + 372a3ec due to reported security and stability issues on previous Core version. This will also support gzipped binaries.

Although it might still compile on previous Core versions all support will be removed in the near future.

Support of TLS

To save resources when TLS is enabled mDNS needs to be disabled. In addition to TLS using fingerprints now also user supplied CA certs and AWS IoT is supported. Read full documentation

Initial configuration tools

For initial configuration this release supports Webserver based WifiManager or Serial based command interface only. Support for WPS and SmartConfig has been removed.

Provided Binary Downloads

The following binary downloads have been compiled with ESP8266/Arduino library core version 2.6.3 + 372a3ec.

tasmota.bin = The Tasmota version with most drivers. RECOMMENDED RELEASE BINARY
tasmota-BG.bin to tasmota-TW.bin = The Tasmota version in different languages.
tasmota-lite.bin = The Lite version without most drivers and sensors.
tasmota-knx.bin = The Knx version without some features but adds KNX support.
tasmota-sensors.bin = The Sensors version adds more useful sensors.
tasmota-ir = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features.
tasmota-display.bin = The Display version without Energy Monitoring but adds display support.
tasmota-minimal.bin = The Minimal version allows intermediate OTA uploads to support larger versions and does NOT change any persistent parameter. This version should NOT be used for initial installation.

List of embedded modules.

Complete list of available feature and sensors.

Changelog

Version 8.1.0.10

Change default my_user_config.h driver and sensor support removing most sensors and adding most drivers
Change Lights: simplified gamma correction and 10 bits internal computation
Change commands Prefix, Ssid, StateText, NTPServer, and FriendlyName displaying all items
Change IRremoteESP8266 library updated to v2.7.4
Change Zigbee command prefix from Zigbee* to Zb*
Change MQTT message size with additional 200 characters
Change display of some date and time messages from "Wed Feb 19 10:45:12 2020" to "2020-02-19T10:45:12"
Change switchmode 6 according to issue 7778 (#7831)
Fix Sonoff Bridge, Sc, L1, iFan03 and CSE7766 serial interface to forced speed, config and disable logging
Fix commands Display and Counter from overruling command processing (#7322)
Fix White added to light status (#7142)
Fix Improved fade linearity with gamma correction
Fix LCD line and column positioning (#7387)
Fix Display handling of hexadecimal escape characters (#7387)
Fix WakeUp <x> ignores provided value (#7473)
Fix exception 9 restart on log message in Ticker interrupt service routines NTP, Wemos and Hue emulation (#7496)
Fix PowerDelta zero power detection (#7515)
Fix RGBWWTable ignored (#7572)
Fix PWM flickering at low levels (#7415)
Fix Hass sensor discovery part 1/4 by Federico Leoni (#7582, #7548)
Fix MaxPower functionality (#7647)
Fix relation between RSSI and signal strength
Add command SetOption79 0/1 to enable reset of counters at teleperiod time by Andre Thomas (#7355)
Add command SetOption82 0/1 to limit the CT range for Alexa to 200..380
Add command SetOption84 0/1 to send AWS IoT device shadow updates (alternative to retained)
Add commands SetOption85 0/1 and DevGroupShare supporting UDP Group command using GroupTopic without MQTT by Paul Diem (#7790)
Add command SetOption86 0/1 for PWM dimmer to turn brightness LED's off 5 seconds after last change
Add command SetOption87 0/1 for PWM dimmer to turn red LED on when powered off
Add command SetOption88 0/1 for PWM dimmer to let buttons control remote devices
Add command SetOption89 0/1 for Zigbee distinct MQTT topics per device for SENSOR, allowing retained messages (#7835)
Add command ShutterButton <parameters> to control shutter(s) by to-scho (#7403)
Add commands SwitchMode 8 ToggleMulti, SwitchMode 9 FollowMulti and SwitchMode 10 FollowMultiInverted (#7522)
Add commands SwitchMode 11 PushHoldMulti and SwitchMode 12 PushHoldInverted (#7603)
Add command Buzzer -1 for infinite mode and command Buzzer -2 for following led mode (#7623)
Add SerialConfig to Status 1
Add WifiPower to Status 5
Add support for DS1624, DS1621 Temperature sensor by Leonid Myravjev
Add Zigbee attribute decoder for Xiaomi Aqara Cube
Add support for AdcParam parameters to control ADC0 Current Transformer Apparent Power formula by Jodi Dillon (#7100)
Add optional support for Prometheus using file xsns_91_prometheus.ino (#7216)
Add experimental support for NRF24L01 as BLE-bridge for Mijia Bluetooth sensors by Christian Baars (#7394)
Add support to BMP driver to enter reset state (sleep enable) when deep sleep is used in Tasmota
Add support for gzipped binaries
Add web page sliders when SetOption37 128 is active allowing control of white(s)
Add most SetOptions as defines to my_user_config.h
Add SoftwareSerial to CSE7766 driver allowing different GPIOs (#7563)
Add optional parameter to command Scheme <scheme>, <startcolor> to control initial start color
Add rule trigger on one level deeper using syntax with two # like on zigbeereceived#vibration_sensor#aqaracubeside=0 do ...
Add support for sensors DS18x20 and DHT family on Shelly 1 and Shelly 1PM using Shelly Add-On adapter (#7469)
Add support for MI-BLE sensors using HM-10 Bluetooth 4.0 module by Christian Staars (#7683)
Add BootCount Reset Time as BCResetTime to Status 1
Add ZbZNPReceivedand ZbZCLReceived being published to MQTT when SetOption66 1
Add optional Wifi AccessPoint passphrase define WIFI_AP_PASSPHRASE in my_user_config.h (#7690)
Add support for FiF LE-01MR energy meter by saper-2 (#7584)
Add new DHT driver. The old driver can still be used using define USE_DHT_OLD (#7468)
Add another new DHT driver based on ESPEasy. The old driver can still be used using define USE_DHT_OLD. The previous new driver can be used with define USE_DHT_V2 (#7717)
Add initial support for Sensors AHT10 and AHT15 by Martin Wagner (#7596)
Add support for Wemos Motor Shield V1 by Denis Sborets (#7764)
Add Zigbee enhanced commands decoding, added ZbPing
Add Zigbee features and improvements
Add support for Martin Jerry/acenx/Tessan/NTONPOWER SD0x PWM dimmer switches by Paul Diem (#7791)
Add support for Jarolift rollers by Keeloq algorithm
Add support for MaxBotix HRXL-MaxSonar ultrasonic range finders by Jon Little (#7814)
Add support for Romanian language translations by Augustin Marti

8.0 KiB Raw Blame History