This separates extmod source files from `py.mk`. Previously, `py.mk`
assumed that every consumer of the py/ directory also wanted to include
extmod/. However, this is not the case. For example, building mpy-cross
uses py/ but doesn't need extmod/.
This commit moves all extmod-specific items from `py.mk` to `extmod.mk` and
explicitly includes `extmod.mk` in ports that use it.
Signed-off-by: David Lechner <david@pybricks.com>
Both led_init and led_state are configurable via MBOOT_BOARD_LED_INIT and
MBOOT_BOARD_LED_STATE respectively, so don't need to be MP_WEAK.
Furthermore, led_state and led0_state are private to ui.c so can be made
static.
Signed-off-by: Damien George <damien@micropython.org>
System config block contains hardware unrelated to USB. So calling
`__SYSCFG_CLK_DISABLE()` during `HAL_PCD_MspDeInit()` has an adverse effect
on other system functionality.
Removing call to `__SYSCFG_CLK_DISABLE()` to rectify this issue.
This call was there since the beginning of the USB CDC code, added in
b30c02afa0.
According to ST Errata ES0206 Rev 18, Section 2.2.1, on STM32F427x,
STM32F437x, STM32F429x and STM32F439x.
If the system tick interrupt is enabled during stop mode while certain
bits are set in the DBGMCU_CR, then the system will immediately wake
from stop mode.
Suggested workaround is to disable system tick timer interrupt when
entering stop mode.
According to ST Errate ES0394 Rev 11, Section 2.2.17, on STM32WB55Cx and
STM32WB35Cx.
If the system tick interrupt is enabled during stop 0, stop 1 or stop 2
while certain bits are set in DBGMCU_CR, then system will immediately
wake from stop mode but the system remains in low power state. The CPU
therefore fetches incorrect data from inactive Flash, which can cause a
hard fault.
Suggested workaround is to disable system tick timer interrupt when
entering stop mode.
This was added by mistake in 8f68e26f79 when
adding support for G4 MCUs, which does not using this get_bank() function.
FLASH_OPTR_DBANK is only defined on G4 and L4 MCUs, so on H7 this
FLASH_BANK_2 code was being wrongly excluded.
Signed-off-by: Damien George <damien@micropython.org>
It's no longer needed because this macro is now processed after
preprocessing the source code via cpp (in the qstr extraction stage), which
means unused MP_REGISTER_MODULE's are filtered out by the preprocessor.
Signed-off-by: Damien George <damien@micropython.org>
The following changes are made:
- Use software SPI for external SPI flash access when building mboot.
- Enable the mboot filesystem-loading feature, with FAT FS support.
- Increase the frequency of the CPU when in mboot to 96MHz, to increase the
speed of SPI flash accesses and programming.
Signed-off-by: Damien George <damien@micropython.org>
This allows a board to modify initial_r0 if needed.
Also make default board behaviour functions always available, named as
mboot_get_reset_mode_default and mboot_state_change_default.
Signed-off-by: Damien George <damien@micropython.org>
For ports with MICROPY_VFS and MICROPY_PY_IO enabled their configuration
can now be simplified to use the defaults for mp_import_stat and
mp_builtin_open.
This commit makes no functional change, except for the following minor
points:
- the built-in "open" is removed from the minimal port (it previously did
nothing)
- the duplicate built-in "input" is removed from the esp32 port
- qemu-arm now delegates to VFS import/open
Signed-off-by: Damien George <damien@micropython.org>
This reverts commit 2668337f36.
The issue with potential breaking of the BLE RX path in the radio is fixed
since WS v1.12.0.
Signed-off-by: Damien George <damien@micropython.org>
This replaces occurences of
foo_t *foo = m_new_obj(foo_t);
foo->base.type = &foo_type;
with
foo_t *foo = mp_obj_malloc(foo_t, &foo_type);
Excludes any places where base is a sub-field or when new0/memset is used.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds a board definition for NUCLEO_G0B1RE. This board has the
REPL on UART2 which is connected to the on-board ST-link USB-UART.
Signed-off-by: Asensio Lorenzo Sempere <asensio.aerospace@gmail.com>
This implements self-triggering of the Flash NVIC interrupt on Cortex-M0
devices, which allows enabling internal storage on those MCUs.
Signed-off-by: Asensio Lorenzo Sempere <asensio.aerospace@gmail.com>
These files that are reformatted only now fall under the list of files to
apply uncrustify/black formatting to.
Signed-off-by: Damien George <damien@micropython.org>
To avoid any I/O glitches in mp_hal_pin_config, make sure a valid alternate
function is set in AFR first before switching the pin mode. When switching
from AF to INPUT or OUTPUT, the AF in AFR will remain valid up until the
pin mode is switched.
David Lechner
Damien George
chrismas9
iabdalkader
Clayton Mills
Andrew Leech
Jim Mussared
Asensio Lorenzo Sempere
Chris Wilson